diff --git a/resources/definitions/fabtotum.def.json b/resources/definitions/fabtotum.def.json
index 87ce11a35c..1f5d9dab0b 100644
--- a/resources/definitions/fabtotum.def.json
+++ b/resources/definitions/fabtotum.def.json
@@ -21,10 +21,10 @@
   "overrides": {
     "machine_name": { "default_value": "FABtotum Personal Fabricator" },
     "machine_start_gcode": {
-      "default_value": ";Layer height: {layer_height}\n;Walls: {wall_thickness}\n;Fill: {infill_sparse_density}\n;Top\\Bottom Thickness: {top_bottom_thickness}\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nG4 S1 ;1 millisecond pause to buffer the bep bep \nM728 ;FAB bep bep (start the print, go check the oozing and skirt lines adesion) \nG4 S1 ;1 second pause to reach the printer (run fast)\nG92 E0 ;zero the extruded length \nG1 F200 E35  ;slowly extrude 35mm of filament to clean the nozzle and build up extrusion pressure \nG92 E0 ;zero the extruded length again \nG1 F{speed_travel} ;Set travel speed \n;print"
+      "default_value": ";Layer height: {layer_height}\n;Walls: {wall_thickness}\n;Fill: {infill_sparse_density}\n;Top\\Bottom Thickness: {top_bottom_thickness}\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nG4 S1 ;1 millisecond pause to buffer the bep bep \nM300 S2 ;FAB bep bep (start the print, go check the oozing and skirt lines adesion) \nG4 S1 ;1 second pause to reach the printer (run fast)\nG92 E0 ;zero the extruded length \nG1 F200 E35  ;slowly extrude 35mm of filament to clean the nozzle and build up extrusion pressure \nG92 E0 ;zero the extruded length again \n;print"
     },
     "machine_end_gcode": {
-      "default_value": "M104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-3 X+5 Y+5 F5000 ;move Z up a bit and retract filament even more\n;end of the print\nM84 ;steppers off\nG90 ;absolute positioning\nM728 ;FAB bep bep (end print)"
+      "default_value": "M104 S0 ;extruder heater off\nM140 S0 ;heated bed heater off (if you have it)\nG91 ;relative positioning\nG1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-3 X+5 Y+5 F5000 ;move Z up a bit and retract filament even more\n;end of the print\nM84 ;steppers off\nG90 ;absolute positioning\nM300 S2 ;FAB bep bep (end print)"
     },
     "gantry_height": { "default_value": 55 },
     "machine_width": { "default_value": 214 },
diff --git a/resources/quality/fabtotum/fabtotum_abs_fast.inst.cfg b/resources/quality/fabtotum/fabtotum_abs_fast.inst.cfg
index 245997a27e..fe68b4a76e 100644
--- a/resources/quality/fabtotum/fabtotum_abs_fast.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_abs_fast.inst.cfg
@@ -12,9 +12,10 @@ weight = -1
 
 [values]
 adhesion_type = raft
+speed_print = 80
 layer_height = 0.2
 layer_height_0 = 0.2
-cool_fan_enabled = True
+cool_fan_enabled = False
 cool_fan_full_at_height = 0.4
 cool_fan_speed = 50
 cool_fan_speed_max = 50
diff --git a/resources/quality/fabtotum/fabtotum_abs_high.inst.cfg b/resources/quality/fabtotum/fabtotum_abs_high.inst.cfg
index 26300eec7d..dd1f58a59a 100644
--- a/resources/quality/fabtotum/fabtotum_abs_high.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_abs_high.inst.cfg
@@ -12,9 +12,10 @@ weight = 1
 
 [values]
 adhesion_type = raft
+speed_print = 45
 layer_height = 0.1
 layer_height_0 = 0.1
-cool_fan_enabled = True
+cool_fan_enabled = False
 cool_fan_full_at_height = 0.2
 cool_fan_speed = 50
 cool_fan_speed_max = 50
diff --git a/resources/quality/fabtotum/fabtotum_abs_normal.inst.cfg b/resources/quality/fabtotum/fabtotum_abs_normal.inst.cfg
index 53d20c8cbc..31c588c498 100644
--- a/resources/quality/fabtotum/fabtotum_abs_normal.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_abs_normal.inst.cfg
@@ -12,9 +12,10 @@ weight = 0
 
 [values]
 adhesion_type = raft
+speed_print = 60
 layer_height = 0.15
 layer_height_0 = 0.15
-cool_fan_enabled = True
+cool_fan_enabled = False
 cool_fan_full_at_height = 0.3
 cool_fan_speed = 50
 cool_fan_speed_max = 50
diff --git a/resources/quality/fabtotum/fabtotum_nylon_fast.inst.cfg b/resources/quality/fabtotum/fabtotum_nylon_fast.inst.cfg
index 22bbcbeaeb..86eb5326e0 100644
--- a/resources/quality/fabtotum/fabtotum_nylon_fast.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_nylon_fast.inst.cfg
@@ -44,7 +44,7 @@ skirt_gap = 1.5
 skirt_line_count = 5
 speed_infill = =speed_print
 speed_layer_0 = 25
-speed_print = 50
+speed_print = 30
 speed_topbottom = 40
 speed_travel = 200
 speed_wall_0 = 40
diff --git a/resources/quality/fabtotum/fabtotum_nylon_high.inst.cfg b/resources/quality/fabtotum/fabtotum_nylon_high.inst.cfg
index a625bd715f..8585323537 100644
--- a/resources/quality/fabtotum/fabtotum_nylon_high.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_nylon_high.inst.cfg
@@ -44,7 +44,7 @@ skirt_gap = 1.5
 skirt_line_count = 5
 speed_infill = =speed_print
 speed_layer_0 = 25
-speed_print = 50
+speed_print = 30
 speed_topbottom = 40
 speed_travel = 200
 speed_wall_0 = 40
diff --git a/resources/quality/fabtotum/fabtotum_nylon_normal.inst.cfg b/resources/quality/fabtotum/fabtotum_nylon_normal.inst.cfg
index b05d30c5c6..99ab0e10cb 100644
--- a/resources/quality/fabtotum/fabtotum_nylon_normal.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_nylon_normal.inst.cfg
@@ -44,7 +44,7 @@ skirt_gap = 1.5
 skirt_line_count = 5
 speed_infill = =speed_print
 speed_layer_0 = 25
-speed_print = 50
+speed_print = 30
 speed_topbottom = 40
 speed_travel = 200
 speed_wall_0 = 40
diff --git a/resources/quality/fabtotum/fabtotum_pla_fast.inst.cfg b/resources/quality/fabtotum/fabtotum_pla_fast.inst.cfg
index 1f1c93961b..5b4cb737ff 100644
--- a/resources/quality/fabtotum/fabtotum_pla_fast.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_pla_fast.inst.cfg
@@ -12,6 +12,7 @@ weight = -1
 
 [values]
 adhesion_type = skirt
+speed_print = 80
 layer_height = 0.2
 layer_height_0 = 0.2
 cool_fan_enabled = True
diff --git a/resources/quality/fabtotum/fabtotum_pla_high.inst.cfg b/resources/quality/fabtotum/fabtotum_pla_high.inst.cfg
index 9cd067703c..e427372010 100644
--- a/resources/quality/fabtotum/fabtotum_pla_high.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_pla_high.inst.cfg
@@ -12,6 +12,7 @@ weight = 1
 
 [values]
 adhesion_type = skirt
+speed_print = 45
 layer_height = 0.1
 layer_height_0 = 0.1
 cool_fan_enabled = True
diff --git a/resources/quality/fabtotum/fabtotum_pla_normal.inst.cfg b/resources/quality/fabtotum/fabtotum_pla_normal.inst.cfg
index 5b5125c4e5..ee22d8fa9a 100644
--- a/resources/quality/fabtotum/fabtotum_pla_normal.inst.cfg
+++ b/resources/quality/fabtotum/fabtotum_pla_normal.inst.cfg
@@ -12,6 +12,7 @@ weight = 0
 
 [values]
 adhesion_type = skirt
+speed_print = 60
 layer_height = 0.15
 layer_height_0 = 0.15
 cool_fan_enabled = True
diff --git a/resources/quality/fabtotum/fabtotum_tpu_fast.inst.cfg b/resources/quality/fabtotum/fabtotum_tpu_fast.inst.cfg
new file mode 100644
index 0000000000..d8ee095d61
--- /dev/null
+++ b/resources/quality/fabtotum/fabtotum_tpu_fast.inst.cfg
@@ -0,0 +1,25 @@
+[general]
+version = 2
+definition = fabtotum
+name = Fast Quality
+
+[metadata]
+type = quality
+setting_version = 4
+material = fabtotum_tpu
+quality_type = fast
+weight = -1
+
+[values]
+adhesion_type = skirt
+speed_print = 80
+layer_height = 0.2
+layer_height_0 = 0.2
+cool_fan_enabled = True
+cool_fan_full_at_height = 0.4
+cool_fan_speed = 100
+cool_fan_speed_max = 100
+cool_fan_speed_min = 100
+cool_min_layer_time = 5
+cool_min_speed = 20
+
diff --git a/resources/quality/fabtotum/fabtotum_tpu_high.inst.cfg b/resources/quality/fabtotum/fabtotum_tpu_high.inst.cfg
new file mode 100644
index 0000000000..315a56015d
--- /dev/null
+++ b/resources/quality/fabtotum/fabtotum_tpu_high.inst.cfg
@@ -0,0 +1,24 @@
+[general]
+version = 2
+definition = fabtotum
+name = High Quality
+
+[metadata]
+type = quality
+setting_version = 4
+material = fabtotum_tpu
+quality_type = high
+weight = 1
+
+[values]
+adhesion_type = skirt
+layer_height = 0.1
+layer_height_0 = 0.1
+cool_fan_enabled = True
+cool_fan_full_at_height = 0.2
+cool_fan_speed = 100
+cool_fan_speed_max = 100
+cool_fan_speed_min = 100
+cool_min_layer_time = 5
+cool_min_speed = 20
+
diff --git a/resources/quality/fabtotum/fabtotum_tpu_normal.inst.cfg b/resources/quality/fabtotum/fabtotum_tpu_normal.inst.cfg
new file mode 100644
index 0000000000..3ce1592e70
--- /dev/null
+++ b/resources/quality/fabtotum/fabtotum_tpu_normal.inst.cfg
@@ -0,0 +1,25 @@
+[general]
+version = 2
+definition = fabtotum
+name = Normal Quality
+
+[metadata]
+type = quality
+setting_version = 4
+material = fabtotum_TPU
+quality_type = normal
+weight = 0
+
+[values]
+adhesion_type = skirt
+speed_print = 80
+layer_height = 0.15
+layer_height_0 = 0.15
+cool_fan_enabled = True
+cool_fan_full_at_height = 0.3
+cool_fan_speed = 100
+cool_fan_speed_max = 100
+cool_fan_speed_min = 100
+cool_min_layer_time = 5
+cool_min_speed = 20
+