Optimise 0.4mm profiles for CPEP, PC and TPU

These optimisations should only remove settings that are exactly equal to the parent profile. Support interface settings are an exception, since they were defining non-existing settings in the original profiles. The stand-by temperature is also an exception, since the stand-by temperature of the material profile is set in stone because of firmware.

Contributes to issue CURA-3650.

resources/quality/ultimaker3/um3_aa0.4_CPEP_Draft_Print.inst.cfg

@@ -11,50 +11,19 @@ weight = -2
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
-adhesion_type = brim
-brim_width = 7
-cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
-cool_fan_speed = 1
 cool_fan_speed_max = 80
-cool_min_layer_time = 5
 cool_min_speed = 5
 infill_line_width = =round(line_width * 0.35 / 0.35, 2)
 infill_overlap = 0
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.2
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
-machine_nozzle_cool_down_speed = 0.9
-machine_nozzle_heat_up_speed = 1.4
-material_bed_temperature = 107
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 material_print_temperature_layer_0 = =material_print_temperature
 material_standby_temperature = 100
@@ -62,34 +31,20 @@ multiple_mesh_overlap = 0
 prime_tower_enable = True
 prime_tower_size = 17
 prime_tower_wipe_enabled = True
-retraction_amount = 7
 retraction_combing = off
-retraction_count_max = 25
 retraction_extrusion_window = 1
 retraction_hop = 0.2
 retraction_hop_enabled = False
 retraction_hop_only_when_collides = True
 skin_overlap = 20
-speed_infill = =speed_print
 speed_layer_0 = 20
-speed_prime_tower = =speed_topbottom
 speed_print = 50
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = =math.ceil(speed_print * 65 / 50)
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 50 / 50)
 speed_wall_0 = =math.ceil(speed_wall * 40 / 50)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
 support_z_distance = =layer_height
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
 wall_0_inset = 0
-wall_line_width_x = =round(line_width * 0.3 / 0.35, 2)
 wall_thickness = 1

resources/quality/ultimaker3/um3_aa0.4_CPEP_Fast_Print.inst.cfg

@@ -11,50 +11,19 @@ weight = -1
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
-adhesion_type = brim
-brim_width = 7
-cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
-cool_fan_speed = 1
 cool_fan_speed_max = 80
-cool_min_layer_time = 5
 cool_min_speed = 6
 infill_line_width = =round(line_width * 0.35 / 0.35, 2)
 infill_overlap = 0
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.15
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
-machine_nozzle_cool_down_speed = 0.9
-machine_nozzle_heat_up_speed = 1.4
-material_bed_temperature = 107
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 material_print_temperature_layer_0 = =material_print_temperature
 material_standby_temperature = 100
@@ -62,34 +31,19 @@ multiple_mesh_overlap = 0
 prime_tower_enable = True
 prime_tower_size = 17
 prime_tower_wipe_enabled = True
-retraction_amount = 7
 retraction_combing = off
-retraction_count_max = 25
 retraction_extrusion_window = 1
 retraction_hop = 0.2
 retraction_hop_enabled = False
 retraction_hop_only_when_collides = True
 skin_overlap = 20
-speed_infill = =speed_print
 speed_layer_0 = 20
-speed_prime_tower = =speed_topbottom
 speed_print = 45
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = =math.ceil(speed_print * 55 / 45)
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 45 / 45)
 speed_wall_0 = =math.ceil(speed_wall * 35 / 45)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
 support_z_distance = =layer_height
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
 wall_0_inset = 0
-wall_line_width_x = =round(line_width * 0.3 / 0.35, 2)
-wall_thickness = 1.3

resources/quality/ultimaker3/um3_aa0.4_CPEP_High_Quality.inst.cfg

@@ -11,50 +11,21 @@ weight = 1
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
-adhesion_type = brim
-brim_width = 7
-cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
-cool_fan_speed = 1
 cool_fan_speed_max = 50
-cool_min_layer_time = 5
 cool_min_speed = 5
 infill_line_width = =round(line_width * 0.35 / 0.35, 2)
 infill_overlap = 0
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.06
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 107
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 2
 material_print_temperature_layer_0 = =material_print_temperature
 material_standby_temperature = 100
@@ -62,34 +33,19 @@ multiple_mesh_overlap = 0
 prime_tower_enable = True
 prime_tower_size = 17
 prime_tower_wipe_enabled = True
-retraction_amount = 7
 retraction_combing = off
-retraction_count_max = 25
 retraction_extrusion_window = 1
 retraction_hop = 0.2
 retraction_hop_enabled = False
 retraction_hop_only_when_collides = True
 skin_overlap = 20
-speed_infill = =speed_print
 speed_layer_0 = 20
-speed_prime_tower = =speed_topbottom
 speed_print = 40
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = =math.ceil(speed_print * 30 / 35)
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 35 / 40)
 speed_wall_0 = =math.ceil(speed_wall * 30 / 35)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
 support_z_distance = =layer_height
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
 wall_0_inset = 0
-wall_line_width_x = =round(line_width * 0.3 / 0.35, 2)
-wall_thickness = 1.3

resources/quality/ultimaker3/um3_aa0.4_CPEP_Normal_Quality.inst.cfg

@@ -11,50 +11,20 @@ weight = 0
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
-adhesion_type = brim
-brim_width = 7
-cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
-cool_fan_speed = 1
 cool_fan_speed_max = 50
-cool_min_layer_time = 5
 cool_min_speed = 7
 infill_line_width = =round(line_width * 0.35 / 0.35, 2)
 infill_overlap = 0
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
-layer_height = 0.1
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 107
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 material_print_temperature_layer_0 = =material_print_temperature
 material_standby_temperature = 100
@@ -62,34 +32,19 @@ multiple_mesh_overlap = 0
 prime_tower_enable = True
 prime_tower_size = 17
 prime_tower_wipe_enabled = True
-retraction_amount = 7
 retraction_combing = off
-retraction_count_max = 25
 retraction_extrusion_window = 1
 retraction_hop = 0.2
 retraction_hop_enabled = False
 retraction_hop_only_when_collides = True
 skin_overlap = 20
-speed_infill = =speed_print
 speed_layer_0 = 20
-speed_prime_tower = =speed_topbottom
 speed_print = 40
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = =math.ceil(speed_print * 30 / 35)
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 35 / 40)
 speed_wall_0 = =math.ceil(speed_wall * 30 / 35)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
 support_z_distance = =layer_height
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
 wall_0_inset = 0
-wall_line_width_x = =round(line_width * 0.3 / 0.35, 2)
-wall_thickness = 1.3

resources/quality/ultimaker3/um3_aa0.4_PC_Draft_Print.inst.cfg

@@ -11,64 +11,34 @@ weight = -2
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
 adhesion_type = raft
 brim_width = 20
 cool_fan_full_at_height = =layer_height_0 + layer_height
-cool_fan_speed = 0
 cool_fan_speed_max = 90
-cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 5
 cool_min_speed = 6
 infill_line_width = =round(line_width * 0.4 / 0.35, 2)
 infill_overlap = 0
 infill_overlap_mm = 0.05
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0.1
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.2
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 107
-material_flow = 100
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 material_standby_temperature = 100
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40
-ooze_shield_dist = 2
 prime_tower_enable = True
 prime_tower_size = 16
 prime_tower_wipe_enabled = True
 raft_airgap = 0.25
-raft_margin = 15
-retraction_amount = 8
 retraction_count_max = 80
 retraction_extrusion_window = 1
 retraction_hop = 2
@@ -76,38 +46,21 @@ retraction_hop_enabled = True
 retraction_hop_only_when_collides = True
 retraction_min_travel = 0.8
 retraction_prime_speed = 15
-retraction_speed = 35
 skin_overlap = 30
-speed_infill = =speed_print
 speed_layer_0 = 25
-speed_prime_tower = =speed_topbottom
 speed_print = 50
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = 25
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 40 / 50)
 speed_wall_0 = =math.ceil(speed_wall * 25 / 40)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_infill_rate = 15
+support_interface_line_distance = 0.4
-support_pattern = zigzag
+support_interface_pattern = lines
-support_roof_density = 100
-support_roof_enable = False
-support_roof_line_distance = 0.4
-support_roof_pattern = lines
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
-support_z_distance = =layer_height * 2
 switch_extruder_prime_speed = 15
 switch_extruder_retraction_amount = 20
 switch_extruder_retraction_speeds = 35
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
-xy_offset = -0.15
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.4 / 0.35, 2)
 wall_thickness = 1.2
+xy_offset = -0.15

resources/quality/ultimaker3/um3_aa0.4_PC_Fast_Print.inst.cfg

@@ -11,63 +11,33 @@ weight = -1
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
 adhesion_type = raft
 brim_width = 20
 cool_fan_full_at_height = =layer_height_0 + layer_height
-cool_fan_speed = 0
 cool_fan_speed_max = 85
-cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 5
 cool_min_speed = 7
 infill_line_width = =round(line_width * 0.4 / 0.35, 2)
 infill_overlap_mm = 0.05
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0.1
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.15
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 107
-material_flow = 100
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 material_standby_temperature = 100
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40
-ooze_shield_dist = 2
 prime_tower_enable = True
 prime_tower_size = 16
 prime_tower_wipe_enabled = True
 raft_airgap = 0.25
-raft_margin = 15
-retraction_amount = 8
 retraction_count_max = 80
 retraction_extrusion_window = 1
 retraction_hop = 2
@@ -75,38 +45,21 @@ retraction_hop_enabled = True
 retraction_hop_only_when_collides = True
 retraction_min_travel = 0.8
 retraction_prime_speed = 15
-retraction_speed = 35
 skin_overlap = 30
-speed_infill = =speed_print
 speed_layer_0 = 25
-speed_prime_tower = =speed_topbottom
 speed_print = 50
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = 25
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 40 / 50)
 speed_wall_0 = =math.ceil(speed_wall * 25 / 40)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_infill_rate = 15
+support_interface_line_distance = 0.4
-support_pattern = zigzag
+support_interface_pattern = lines
-support_roof_density = 100
-support_roof_enable = False
-support_roof_line_distance = 0.4
-support_roof_pattern = lines
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
-support_z_distance = =layer_height * 2
 switch_extruder_prime_speed = 15
 switch_extruder_retraction_amount = 20
 switch_extruder_retraction_speeds = 35
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
-xy_offset = -0.15
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.4 / 0.35, 2)
 wall_thickness = 1.2
+xy_offset = -0.15

resources/quality/ultimaker3/um3_aa0.4_PC_High_Quality.inst.cfg

@@ -11,64 +11,34 @@ weight = 1
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
 adhesion_type = raft
 brim_width = 20
 cool_fan_full_at_height = =layer_height_0 + layer_height
-cool_fan_speed = 0
 cool_fan_speed_max = 50
-cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 5
 cool_min_speed = 8
 infill_line_width = =round(line_width * 0.4 / 0.35, 2)
 infill_overlap = 0
 infill_overlap_mm = 0.05
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0.1
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.06
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 107
-material_flow = 100
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature - 10
 material_standby_temperature = 100
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40
-ooze_shield_dist = 2
 prime_tower_enable = True
 prime_tower_size = 16
 prime_tower_wipe_enabled = True
 raft_airgap = 0.25
-raft_margin = 15
-retraction_amount = 8
 retraction_count_max = 80
 retraction_extrusion_window = 1
 retraction_hop = 2
@@ -76,39 +46,21 @@ retraction_hop_enabled = True
 retraction_hop_only_when_collides = True
 retraction_min_travel = 0.8
 retraction_prime_speed = 15
-retraction_speed = 35
 skin_overlap = 30
-speed_infill = =speed_print
 speed_layer_0 = 25
-speed_prime_tower = =speed_topbottom
 speed_print = 50
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = 25
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 40 / 50)
 speed_wall_0 = =math.ceil(speed_wall * 25 / 40)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_infill_rate = 15
+support_interface_line_distance = 0.4
-support_pattern = zigzag
+support_interface_pattern = lines
-support_roof_density = 100
-support_roof_enable = False
-support_roof_line_distance = 0.4
-support_roof_pattern = lines
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
-support_z_distance = =layer_height * 2
 switch_extruder_prime_speed = 15
 switch_extruder_retraction_amount = 20
 switch_extruder_retraction_speeds = 35
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
-xy_offset = -0.15
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.4 / 0.35, 2)
 wall_thickness = 1.2
-
+xy_offset = -0.15

resources/quality/ultimaker3/um3_aa0.4_PC_Normal_Quality.inst.cfg

@@ -11,64 +11,32 @@ weight = 0
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
 adhesion_type = raft
 brim_width = 20
 cool_fan_full_at_height = =layer_height_0 + layer_height
-cool_fan_speed = 0
 cool_fan_speed_max = 50
-cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 5
 cool_min_speed = 5
 infill_line_width = =round(line_width * 0.4 / 0.35, 2)
 infill_overlap = 0
 infill_overlap_mm = 0.05
 infill_pattern = triangles
-infill_sparse_density = 20
 infill_wipe_dist = 0.1
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
-layer_height = 0.1
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
-line_width = =machine_nozzle_size * 0.875
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 107
-material_flow = 100
-material_initial_print_temperature = =material_print_temperature - 5
 material_final_print_temperature = =material_print_temperature - 10
-material_print_temperature = =default_material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 5
 material_standby_temperature = 100
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40
-ooze_shield_dist = 2
 prime_tower_enable = True
 prime_tower_size = 16
 prime_tower_wipe_enabled = True
 raft_airgap = 0.25
-raft_margin = 15
-retraction_amount = 8
 retraction_count_max = 80
 retraction_extrusion_window = 1
 retraction_hop = 2
@@ -76,38 +44,21 @@ retraction_hop_enabled = True
 retraction_hop_only_when_collides = True
 retraction_min_travel = 0.8
 retraction_prime_speed = 15
-retraction_speed = 35
 skin_overlap = 30
-speed_infill = =speed_print
 speed_layer_0 = 25
-speed_prime_tower = =speed_topbottom
 speed_print = 50
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = 25
 speed_travel = 250
 speed_wall = =math.ceil(speed_print * 40 / 50)
 speed_wall_0 = =math.ceil(speed_wall * 25 / 40)
-speed_wall_x = =speed_wall
-support_angle = 60
 support_bottom_distance = =support_z_distance
-support_infill_rate = 15
+support_interface_line_distance = 0.4
-support_pattern = zigzag
+support_interface_pattern = lines
-support_roof_density = 100
-support_roof_enable = False
-support_roof_line_distance = 0.4
-support_roof_pattern = lines
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
-support_z_distance = =layer_height * 2
 switch_extruder_prime_speed = 15
 switch_extruder_retraction_amount = 20
 switch_extruder_retraction_speeds = 35
-top_bottom_thickness = 1.2
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
-xy_offset = -0.15
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.4 / 0.35, 2)
 wall_thickness = 1.2
+xy_offset = -0.15

resources/quality/ultimaker3/um3_aa0.4_TPU_Draft_Print.inst.cfg

@@ -11,23 +11,9 @@ weight = -2
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
-adhesion_type = brim
 brim_width = 8.75
-cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
-cool_fan_speed = 20
 cool_fan_speed_max = 100
-cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 6
 cool_min_speed = 4
 gradual_infill_step_height = =5 * layer_height
@@ -38,24 +24,12 @@ infill_pattern = tetrahedral
 infill_sparse_density = 96
 infill_wipe_dist = 0.1
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.2
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
 line_width = =machine_nozzle_size * 0.95
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 0
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
 material_initial_print_temperature = =material_print_temperature - 5
@@ -66,7 +40,6 @@ multiple_mesh_overlap = 0
 prime_tower_enable = True
 prime_tower_size = 16
 prime_tower_wipe_enabled = True
-retraction_amount = 6.5
 retraction_count_max = 12
 retraction_extra_prime_amount = 0.8
 retraction_extrusion_window = 1
@@ -75,32 +48,19 @@ retraction_hop_enabled = True
 retraction_hop_only_when_collides = True
 retraction_min_travel = 0.8
 retraction_prime_speed = 15
-retraction_speed = 35
-skin_overlap = 15
 speed_equalize_flow_enabled = True
-speed_infill = =speed_print
 speed_layer_0 = 18
-speed_prime_tower = =speed_topbottom
 speed_print = 25
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = =math.ceil(speed_print * 25 / 25)
 speed_travel = 300
 speed_wall = =math.ceil(speed_print * 25 / 25)
 speed_wall_0 = =math.ceil(speed_wall * 25 / 25)
-speed_wall_x = =speed_wall
 support_angle = 50
-support_bottom_distance = =support_z_distance / 2
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
-support_z_distance = =layer_height * 2
 switch_extruder_prime_speed = 15
 switch_extruder_retraction_amount = 20
 switch_extruder_retraction_speeds = 35
 top_bottom_thickness = 0.7
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
 wall_0_inset = 0
 wall_line_width_x = =line_width
 wall_thickness = 0.76

resources/quality/ultimaker3/um3_aa0.4_TPU_Fast_Print.inst.cfg

@@ -11,23 +11,9 @@ weight = -1
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
-adhesion_type = brim
 brim_width = 8.75
-cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
-cool_fan_speed = 20
 cool_fan_speed_max = 100
-cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 6
 cool_min_speed = 4
 gradual_infill_step_height = =5 * layer_height
@@ -38,24 +24,12 @@ infill_pattern = tetrahedral
 infill_sparse_density = 96
 infill_wipe_dist = 0.1
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
 layer_height = 0.15
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
 line_width = =machine_nozzle_size * 0.95
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 0
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
 material_initial_print_temperature = =material_print_temperature - 5
@@ -75,32 +49,19 @@ retraction_hop_enabled = True
 retraction_hop_only_when_collides = True
 retraction_min_travel = 0.8
 retraction_prime_speed = 15
-retraction_speed = 35
-skin_overlap = 15
 speed_equalize_flow_enabled = True
-speed_infill = =speed_print
 speed_layer_0 = 18
-speed_prime_tower = =speed_topbottom
 speed_print = 25
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = =math.ceil(speed_print * 25 / 25)
 speed_travel = 300
 speed_wall = =math.ceil(speed_print * 25 / 25)
 speed_wall_0 = =math.ceil(speed_wall * 25 / 25)
-speed_wall_x = =speed_wall
 support_angle = 50
-support_bottom_distance = =support_z_distance / 2
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
-support_z_distance = =layer_height * 2
 switch_extruder_prime_speed = 15
 switch_extruder_retraction_amount = 20
 switch_extruder_retraction_speeds = 35
 top_bottom_thickness = 0.7
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
 wall_0_inset = 0
 wall_line_width_x = =line_width
 wall_thickness = 0.76

resources/quality/ultimaker3/um3_aa0.4_TPU_Normal_Quality.inst.cfg

@@ -11,23 +11,9 @@ weight = 0
 
 [values]
 acceleration_enabled = True
-acceleration_infill = =acceleration_print
-acceleration_layer_0 = =acceleration_topbottom
-acceleration_prime_tower = =math.ceil(acceleration_print * 2000 / 4000)
 acceleration_print = 4000
-acceleration_support = =math.ceil(acceleration_print * 2000 / 4000)
-acceleration_support_infill = =acceleration_support
-acceleration_support_interface = =acceleration_topbottom
-acceleration_topbottom = =math.ceil(acceleration_print * 500 / 4000)
-acceleration_wall = =math.ceil(acceleration_print * 1000 / 4000)
-acceleration_wall_0 = =math.ceil(acceleration_wall * 500 / 1000)
-acceleration_wall_x = =acceleration_wall
-adhesion_type = brim
 brim_width = 8.75
-cool_fan_full_at_height = =layer_height_0 + 4 * layer_height
-cool_fan_speed = 20
 cool_fan_speed_max = 100
-cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 6
 cool_min_speed = 4
 gradual_infill_step_height = =5 * layer_height
@@ -38,35 +24,20 @@ infill_pattern = tetrahedral
 infill_sparse_density = 96
 infill_wipe_dist = 0.1
 jerk_enabled = True
-jerk_infill = =jerk_print
-jerk_layer_0 = =jerk_topbottom
-jerk_prime_tower = =math.ceil(jerk_print * 15 / 25)
 jerk_print = 25
-jerk_support = =math.ceil(jerk_print * 15 / 25)
-jerk_support_infill = =jerk_support
-jerk_support_interface = =jerk_topbottom
-jerk_topbottom = =math.ceil(jerk_print * 5 / 25)
-jerk_wall = =math.ceil(jerk_print * 10 / 25)
-jerk_wall_0 = =math.ceil(jerk_wall * 5 / 10)
-jerk_wall_x = =jerk_wall
-layer_height = 0.1
-layer_height_0 = =round(machine_nozzle_size / 1.5, 2)
 line_width = =machine_nozzle_size * 0.95
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_bed_temperature = 0
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
 material_initial_print_temperature = =material_print_temperature - 10
-material_print_temperature = =default_material_print_temperature
 material_print_temperature_layer_0 = =default_material_print_temperature
 material_standby_temperature = 100
 multiple_mesh_overlap = 0
 prime_tower_enable = True
 prime_tower_size = 16
 prime_tower_wipe_enabled = True
-retraction_amount = 6.5
 retraction_count_max = 12
 retraction_extra_prime_amount = 0.8
 retraction_extrusion_window = 1
@@ -75,32 +46,19 @@ retraction_hop_enabled = True
 retraction_hop_only_when_collides = True
 retraction_min_travel = 0.8
 retraction_prime_speed = 15
-retraction_speed = 35
-skin_overlap = 15
 speed_equalize_flow_enabled = True
-speed_infill = =speed_print
 speed_layer_0 = 18
-speed_prime_tower = =speed_topbottom
 speed_print = 25
-speed_support = =speed_wall_0
-speed_support_interface = =speed_topbottom
 speed_topbottom = =math.ceil(speed_print * 25 / 25)
 speed_travel = 300
 speed_wall = =math.ceil(speed_print * 25 / 25)
 speed_wall_0 = =math.ceil(speed_wall * 25 / 25)
-speed_wall_x = =speed_wall
 support_angle = 50
-support_bottom_distance = =support_z_distance / 2
-support_top_distance = =support_z_distance
-support_xy_distance = =wall_line_width_0 * 2.5
-support_xy_distance_overhang = =wall_line_width_0
-support_z_distance = =layer_height * 2
 switch_extruder_prime_speed = 15
 switch_extruder_retraction_amount = 20
 switch_extruder_retraction_speeds = 35
 top_bottom_thickness = 0.7
 travel_avoid_distance = 3
-travel_compensate_overlapping_walls_enabled = True
 wall_0_inset = 0
 wall_line_width_x = =line_width
 wall_thickness = 0.76