diff --git a/resources/definitions/fdmprinter.def.json b/resources/definitions/fdmprinter.def.json index 4b634c3b76..dd2755e7b8 100755 --- a/resources/definitions/fdmprinter.def.json +++ b/resources/definitions/fdmprinter.def.json @@ -746,7 +746,7 @@ "support_interface_line_width": { "label": "Support Interface Line Width", - "description": "Width of a single support interface line.", + "description": "Width of a single line of support roof or floor.", "unit": "mm", "default_value": 0.4, "minimum_value": "0.001", @@ -762,8 +762,8 @@ { "support_bottom_line_width": { - "label": "Support Bottom Line Width", - "description": "Width of a single support bottom line.", + "label": "Support Floor Line Width", + "description": "Width of a single support floor line.", "unit": "mm", "default_value": 0.4, "minimum_value": "0.001", @@ -1958,7 +1958,7 @@ "speed_support_interface": { "label": "Support Interface Speed", - "description": "The speed at which the roofs and bottoms of support are printed. Printing them at lower speeds can improve overhang quality.", + "description": "The speed at which the roofs and floors of support are printed. Printing them at lower speeds can improve overhang quality.", "unit": "mm/s", "type": "float", "default_value": 40, @@ -1974,8 +1974,8 @@ { "speed_support_bottom": { - "label": "Support Bottom Speed", - "description": "The speed at which the bottoms of support are printed. Printing them at lower speeds can improve adhesion of support on top of your model.", + "label": "Support Floor Speed", + "description": "The speed at which the floor of support is printed. Printing it at lower speed can improve adhesion of support on top of your model.", "unit": "mm/s", "type": "float", "default_value": 40, @@ -2279,7 +2279,7 @@ "acceleration_support_interface": { "label": "Support Interface Acceleration", - "description": "The acceleration with which the roofs and bottoms of support are printed. Printing them at lower acceleration can improve overhang quality.", + "description": "The acceleration with which the roofs and floors of support are printed. Printing them at lower acceleration can improve overhang quality.", "unit": "mm/s²", "type": "float", "default_value": 3000, @@ -2295,8 +2295,8 @@ { "acceleration_support_bottom": { - "label": "Support Bottom Acceleration", - "description": "The acceleration with which the bottoms of support are printed. Printing them at lower acceleration can improve adhesion of support on top of your model.", + "label": "Support Floor Acceleration", + "description": "The acceleration with which the floors of support are printed. Printing them at lower acceleration can improve adhesion of support on top of your model.", "unit": "mm/s²", "type": "float", "default_value": 3000, @@ -2553,7 +2553,7 @@ "jerk_support_interface": { "label": "Support Interface Jerk", - "description": "The maximum instantaneous velocity change with which the roofs and bottoms of support are printed.", + "description": "The maximum instantaneous velocity change with which the roofs and floors of support are printed.", "unit": "mm/s", "type": "float", "default_value": 20, @@ -2569,8 +2569,8 @@ { "jerk_support_bottom": { - "label": "Support Bottom Jerk", - "description": "The maximum instantaneous velocity change with which the bottoms of support are printed.", + "label": "Support Floor Jerk", + "description": "The maximum instantaneous velocity change with which the floors of support are printed.", "unit": "mm/s", "type": "float", "default_value": 20, @@ -3044,8 +3044,8 @@ { "support_bottom_extruder_nr": { - "label": "Support Bottom Extruder", - "description": "The extruder train to use for printing the bottoms of the support. This is used in multi-extrusion.", + "label": "Support Floor Extruder", + "description": "The extruder train to use for printing the floors of the support. This is used in multi-extrusion.", "type": "extruder", "default_value": "0", "value": "support_interface_extruder_nr", @@ -3299,8 +3299,8 @@ { "support_bottom_enable": { - "label": "Enable Support Bottom", - "description": "Generate dense floors below the support where it rests on the model. This will create a skin between the model and support.", + "label": "Enable Support Floor", + "description": "Generate a dense slab of material below the support where it rests on the model. This will create a skin between the model and support.", "type": "bool", "default_value": false, "value": "support_interface_enable", @@ -3353,8 +3353,8 @@ }, "support_bottom_height": { - "label": "Support Bottom Thickness", - "description": "The thickness of the support bottoms. This controls the number of dense layers are printed on top of places of a model on which support rests.", + "label": "Support Floor Thickness", + "description": "The thickness of the support floors. This controls the number of dense layers that are printed on top of places of a model on which support rests.", "unit": "mm", "type": "float", "default_value": 1, @@ -3397,8 +3397,8 @@ { "support_bottom_density": { - "label": "Support Bottom Density", - "description": "The density of the bottoms of the support structure. A higher value results in better adhesion of the support on top of the model.", + "label": "Support Floor Density", + "description": "The density of the floors of the support structure. A higher value results in better adhesion of the support on top of the model.", "unit": "%", "type": "float", "default_value": 100, @@ -3412,8 +3412,8 @@ { "support_bottom_line_distance": { - "label": "Support Bottom Line Distance", - "description": "Distance between the printed support bottom lines. This setting is calculated by the Support Bottom Density, but can be adjusted separately.", + "label": "Support Floor Line Distance", + "description": "Distance between the printed support floor lines. This setting is calculated by the Support Floor Density, but can be adjusted separately.", "unit": "mm", "type": "float", "default_value": 0.4, @@ -3484,8 +3484,8 @@ { "support_bottom_pattern": { - "label": "Support Bottom Pattern", - "description": "The pattern with which the bottoms of the support are printed.", + "label": "Support Floor Pattern", + "description": "The pattern with which the floors of the support are printed.", "type": "enum", "options": {