Sort all UM2+ profiles

This will make it easier to modify these profiles in the future.

resources/quality/ultimaker2_plus/pla_0.25_normal.inst.cfg

@@ -11,11 +11,12 @@ quality_type = high
 setting_version = 2
 
 [values]
-layer_height = 0.06
-wall_thickness = 0.88
-top_bottom_thickness = 0.72
-infill_sparse_density = 22
-speed_print = 30
-speed_layer_0 = =round(speed_print * 30 / 30)
 cool_min_layer_time = 5
 cool_min_speed = 10
+infill_sparse_density = 22
+layer_height = 0.06
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+top_bottom_thickness = 0.72
+wall_thickness = 0.88
+

resources/quality/ultimaker2_plus/pla_0.4_fast.inst.cfg

@@ -11,14 +11,15 @@ quality_type = fast
 setting_version = 2
 
 [values]
-layer_height = 0.15
-wall_thickness = 0.7
-top_bottom_thickness = 0.75
-infill_sparse_density = 18
-speed_print = 60
-speed_layer_0 = =round(speed_print * 30 / 60)
-speed_wall = 50
-speed_topbottom = 30
-speed_travel = 150
 cool_min_layer_time = 5
 cool_min_speed = 10
+infill_sparse_density = 18
+layer_height = 0.15
+speed_layer_0 = =round(speed_print * 30 / 60)
+speed_print = 60
+speed_topbottom = 30
+speed_travel = 150
+speed_wall = 50
+top_bottom_thickness = 0.75
+wall_thickness = 0.7
+

resources/quality/ultimaker2_plus/pla_0.4_high.inst.cfg

@@ -11,12 +11,13 @@ quality_type = high
 setting_version = 2
 
 [values]
-layer_height = 0.06
-wall_thickness = 1.05
-top_bottom_thickness = 0.72
-infill_sparse_density = 22
-speed_print = 50
-speed_layer_0 = =round(speed_print * 30 / 50)
-speed_topbottom = 20
 cool_min_layer_time = 5
 cool_min_speed = 10
+infill_sparse_density = 22
+layer_height = 0.06
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 50
+speed_topbottom = 20
+top_bottom_thickness = 0.72
+wall_thickness = 1.05
+

resources/quality/ultimaker2_plus/pla_0.4_normal.inst.cfg

@@ -11,12 +11,13 @@ quality_type = normal
 setting_version = 2
 
 [values]
-layer_height = 0.1
-wall_thickness = 1.05
-top_bottom_thickness = 0.8
-infill_sparse_density = 20
-speed_print = 50
-speed_layer_0 = =round(speed_print * 30 / 50)
-speed_topbottom = 20
 cool_min_layer_time = 5
 cool_min_speed = 10
+infill_sparse_density = 20
+layer_height = 0.1
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 50
+speed_topbottom = 20
+top_bottom_thickness = 0.8
+wall_thickness = 1.05
+

resources/quality/ultimaker2_plus/pla_0.6_normal.inst.cfg

@@ -11,14 +11,15 @@ quality_type = normal
 setting_version = 2
 
 [values]
-layer_height = 0.15
-wall_thickness = 1.59
-top_bottom_thickness = 1.2
-infill_sparse_density = 20
-speed_print = 55
-speed_layer_0 = =round(speed_print * 30 / 55)
-speed_wall = 40
-speed_wall_0 = 25
-speed_topbottom = 20
 cool_min_layer_time = 5
 cool_min_speed = 10
+infill_sparse_density = 20
+layer_height = 0.15
+speed_layer_0 = =round(speed_print * 30 / 55)
+speed_print = 55
+speed_topbottom = 20
+speed_wall = 40
+speed_wall_0 = 25
+top_bottom_thickness = 1.2
+wall_thickness = 1.59
+

resources/quality/ultimaker2_plus/pla_0.8_normal.inst.cfg

@@ -11,12 +11,13 @@ quality_type = fast
 setting_version = 2
 
 [values]
-layer_height = 0.2
-wall_thickness = 2.1
-top_bottom_thickness = 1.2
-infill_sparse_density = 20
-speed_print = 40
-speed_layer_0 = =round(speed_print * 30 / 40)
-speed_wall_0 = 25
 cool_min_layer_time = 5
 cool_min_speed = 10
+infill_sparse_density = 20
+layer_height = 0.2
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+speed_wall_0 = 25
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
+

resources/quality/ultimaker2_plus/um2p_abs_0.25_normal.inst.cfg

@@ -11,15 +11,14 @@ quality_type = high
 setting_version = 2
 
 [values]
-layer_height = 0.06
-wall_thickness = 0.88
-top_bottom_thickness = 0.72
-infill_sparse_density = 22
-speed_print = 30
-speed_layer_0 = =round(speed_print * 30 / 30)
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.2
-cool_min_speed = 10
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 15
-
+cool_min_speed = 10
+infill_sparse_density = 22
+layer_height = 0.06
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+top_bottom_thickness = 0.72
+wall_thickness = 0.88
 

resources/quality/ultimaker2_plus/um2p_abs_0.4_fast.inst.cfg

@@ -11,17 +11,17 @@ quality_type = fast
 setting_version = 2
 
 [values]
-layer_height = 0.15
+cool_fan_speed_min = =cool_fan_speed * 0.2
-wall_thickness = 0.7
+cool_min_layer_time = 3
-top_bottom_thickness = 0.75
+cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
 infill_sparse_density = 18
-speed_print = 55
+layer_height = 0.15
 speed_layer_0 = =round(speed_print * 30 / 55)
-speed_wall = 40
+speed_print = 55
 speed_topbottom = 30
 speed_travel = 150
-cool_min_layer_time = 3
+speed_wall = 40
-cool_fan_speed_min = =cool_fan_speed * 0.2
+top_bottom_thickness = 0.75
-cool_min_speed = 10
+wall_thickness = 0.7
-cool_min_layer_time_fan_speed_max = 15
 

resources/quality/ultimaker2_plus/um2p_abs_0.4_high.inst.cfg

@@ -11,15 +11,15 @@ quality_type = high
 setting_version = 2
 
 [values]
-layer_height = 0.06
-wall_thickness = 1.05
-top_bottom_thickness = 0.72
-infill_sparse_density = 22
-speed_print = 45
-speed_layer_0 = =round(speed_print * 30 / 45)
-speed_wall = 30
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.2
-cool_min_speed = 10
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 22
+layer_height = 0.06
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall = 30
+top_bottom_thickness = 0.72
+wall_thickness = 1.05
 

resources/quality/ultimaker2_plus/um2p_abs_0.4_normal.inst.cfg

@@ -11,14 +11,15 @@ quality_type = normal
 setting_version = 2
 
 [values]
-layer_height = 0.1
-wall_thickness = 1.05
-top_bottom_thickness = 0.8
-infill_sparse_density = 20
-speed_print = 45
-speed_layer_0 = =round(speed_print * 30 / 45)
-speed_wall = 30
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.2
-cool_min_speed = 10
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+layer_height = 0.1
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall = 30
+top_bottom_thickness = 0.8
+wall_thickness = 1.05
+

resources/quality/ultimaker2_plus/um2p_abs_0.6_normal.inst.cfg

@@ -11,16 +11,15 @@ quality_type = normal
 setting_version = 2
 
 [values]
-layer_height = 0.15
-wall_thickness = 1.59
-top_bottom_thickness = 1.2
-infill_sparse_density = 20
-speed_print = 40
-speed_layer_0 = =round(speed_print * 30 / 40)
-speed_infill = 55
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.5
-cool_min_speed = 20
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 20
-
+cool_min_speed = 20
+infill_sparse_density = 20
+layer_height = 0.15
+speed_infill = 55
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 1.59
 

resources/quality/ultimaker2_plus/um2p_abs_0.8_normal.inst.cfg

@@ -11,14 +11,14 @@ quality_type = fast
 setting_version = 2
 
 [values]
-layer_height = 0.2
-wall_thickness = 2.1
-top_bottom_thickness = 1.2
-infill_sparse_density = 20
-speed_print = 40
-speed_layer_0 = =round(speed_print * 30 / 40)
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.5
-cool_min_speed = 15
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 25
+cool_min_speed = 15
+infill_sparse_density = 20
+layer_height = 0.2
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
 

resources/quality/ultimaker2_plus/um2p_cpe_0.25_normal.inst.cfg

@@ -11,14 +11,14 @@ quality_type = high
 setting_version = 2
 
 [values]
-layer_height = 0.06
-wall_thickness = 0.88
-top_bottom_thickness = 0.72
-infill_sparse_density = 22
-speed_print = 30
-speed_layer_0 = =round(speed_print * 30 / 30)
-cool_min_layer_time = 2
 cool_fan_speed_min = =cool_fan_speed * 0.2
-cool_min_speed = 15
+cool_min_layer_time = 2
 cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 15
+infill_sparse_density = 22
+layer_height = 0.06
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+top_bottom_thickness = 0.72
+wall_thickness = 0.88
 

resources/quality/ultimaker2_plus/um2p_cpe_0.4_fast.inst.cfg

@@ -11,17 +11,16 @@ quality_type = fast
 setting_version = 2
 
 [values]
-layer_height = 0.15
-wall_thickness = 0.7
-top_bottom_thickness = 0.75
-infill_sparse_density = 18
-speed_print = 45
-speed_layer_0 = =round(speed_print * 30 / 45)
-speed_wall = 40
-speed_travel = 150
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.8
-cool_min_speed = 10
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 15
-
+cool_min_speed = 10
+infill_sparse_density = 18
+layer_height = 0.15
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_travel = 150
+speed_wall = 40
+top_bottom_thickness = 0.75
+wall_thickness = 0.7
 

resources/quality/ultimaker2_plus/um2p_cpe_0.4_high.inst.cfg

@@ -11,14 +11,15 @@ quality_type = high
 setting_version = 2
 
 [values]
-layer_height = 0.06
-wall_thickness = 1.05
-top_bottom_thickness = 0.72
-infill_sparse_density = 22
-speed_print = 45
-speed_layer_0 = =round(speed_print * 30 / 45)
-speed_wall = 30
-cool_min_layer_time = 2
 cool_fan_speed_min = =cool_fan_speed * 0.8
-cool_min_speed = 15
+cool_min_layer_time = 2
 cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 15
+infill_sparse_density = 22
+layer_height = 0.06
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall = 30
+top_bottom_thickness = 0.72
+wall_thickness = 1.05
+

resources/quality/ultimaker2_plus/um2p_cpe_0.4_normal.inst.cfg

@@ -11,15 +11,15 @@ quality_type = normal
 setting_version = 2
 
 [values]
-layer_height = 0.1
-wall_thickness = 1.05
-top_bottom_thickness = 0.8
-infill_sparse_density = 20
-speed_print = 45
-speed_layer_0 = =round(speed_print * 30 / 45)
-speed_wall = 30
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.8
-cool_min_speed = 10
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 15
+cool_min_speed = 10
+infill_sparse_density = 20
+layer_height = 0.1
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall = 30
+top_bottom_thickness = 0.8
+wall_thickness = 1.05
 

resources/quality/ultimaker2_plus/um2p_cpe_0.6_normal.inst.cfg

@@ -11,13 +11,14 @@ quality_type = normal
 setting_version = 2
 
 [values]
-layer_height = 0.15
-wall_thickness = 1.59
-top_bottom_thickness = 1.2
-infill_sparse_density = 20
-speed_print = 40
-speed_layer_0 = =round(speed_print * 30 / 40)
-cool_min_layer_time = 5
 cool_fan_speed_min = =cool_fan_speed * 0.8
-cool_min_speed = 8
+cool_min_layer_time = 5
 cool_min_layer_time_fan_speed_max = 20
+cool_min_speed = 8
+infill_sparse_density = 20
+layer_height = 0.15
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 1.59
+

resources/quality/ultimaker2_plus/um2p_cpe_0.8_normal.inst.cfg

@@ -11,13 +11,14 @@ quality_type = fast
 setting_version = 2
 
 [values]
-layer_height = 0.2
-wall_thickness = 2.1
-top_bottom_thickness = 1.2
-infill_sparse_density = 20
-speed_print = 40
-speed_layer_0 = =round(speed_print * 30 / 40)
-cool_min_layer_time = 3
 cool_fan_speed_min = =cool_fan_speed * 0.8
-cool_min_speed = 8
+cool_min_layer_time = 3
 cool_min_layer_time_fan_speed_max = 25
+cool_min_speed = 8
+infill_sparse_density = 20
+layer_height = 0.2
+speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
+

resources/quality/ultimaker2_plus/um2p_cpep_0.4_draft.inst.cfg

@@ -11,33 +11,33 @@ quality_type = draft
 setting_version = 2
 
 [values]
-speed_wall_x = 25
-support_z_distance = 0.26
-raft_interface_line_spacing = 1
-cool_min_speed = 8
-cool_fan_speed = 50
-wall_thickness = 1.14
-raft_margin = 15
-speed_layer_0 = 15
-raft_airgap = 0.37
-infill_overlap = 5
-layer_height = 0.2
-raft_interface_line_width = 0.8
-top_bottom_thickness = 1.5
-cool_fan_speed_min = =cool_fan_speed * 25 / 50
-raft_surface_line_width = 0.38
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-speed_wall_0 = 20
 adhesion_type = raft
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
 infill_sparse_density = 30
 layer_0_z_overlap = 0.22
-cool_min_layer_time = 3
+layer_height = 0.2
-speed_print = 25
 line_width = 0.38
-support_angle = 45
+raft_airgap = 0.37
 raft_base_line_spacing = 1.6
 raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.38
+speed_layer_0 = 15
+speed_print = 25
+speed_topbottom = 20
+speed_wall_0 = 20
+speed_wall_x = 25
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.5
+wall_thickness = 1.14
 

resources/quality/ultimaker2_plus/um2p_cpep_0.4_normal.inst.cfg

@@ -11,33 +11,33 @@ quality_type = normal
 setting_version = 2
 
 [values]
-speed_wall_x = 30
-support_z_distance = 0.26
-raft_interface_line_spacing = 1
-cool_min_speed = 8
-cool_fan_speed = 50
-wall_thickness = 1.14
-raft_margin = 15
-speed_layer_0 = 15
-raft_airgap = 0.37
-infill_overlap = 5
-layer_height = 0.15
-raft_interface_line_width = 0.8
-top_bottom_thickness = 1.5
-cool_fan_speed_min = =cool_fan_speed * 25 / 50
-raft_surface_line_width = 0.38
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-speed_wall_0 = 20
 adhesion_type = raft
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
 infill_sparse_density = 30
 layer_0_z_overlap = 0.22
-cool_min_layer_time = 3
+layer_height = 0.15
-speed_print = 35
 line_width = 0.38
-support_angle = 45
+raft_airgap = 0.37
 raft_base_line_spacing = 1.6
 raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.38
+speed_layer_0 = 15
+speed_print = 35
+speed_topbottom = 20
+speed_wall_0 = 20
+speed_wall_x = 30
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.5
+wall_thickness = 1.14
 

resources/quality/ultimaker2_plus/um2p_cpep_0.6_draft.inst.cfg

@@ -11,37 +11,37 @@ quality_type = draft
 setting_version = 2
 
 [values]
-support_xy_distance = 0.6
-speed_travel = 150
-support_z_distance = 0.22
-speed_wall_x = 25
-cool_min_speed = 8
-cool_fan_speed = 45
-raft_surface_thickness = 0.2
-raft_surface_line_width = 0.57
-raft_interface_line_spacing = 1.4
-raft_margin = 15
-raft_airgap = 0.37
-infill_overlap = 5
-layer_height = 0.3
-raft_base_line_spacing = 2.4
-raft_interface_line_width = 1.2
-speed_wall_0 = 20
-cool_fan_speed_min = =cool_fan_speed * 25 / 45
-wall_thickness = 1.14
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-infill_sparse_density = 35
-top_bottom_thickness = 0.75
 adhesion_type = raft
-line_width = 0.57
+cool_fan_speed = 45
-layer_0_z_overlap = 0.22
+cool_fan_speed_min = =cool_fan_speed * 25 / 45
-raft_base_line_width = 1.2
-speed_print = 25
-speed_layer_0 = =round(speed_print * 30 / 50)
-support_line_distance = 2.85
-support_angle = 45
 cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 35
+layer_0_z_overlap = 0.22
+layer_height = 0.3
+line_width = 0.57
+raft_airgap = 0.37
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.57
+raft_surface_thickness = 0.2
+speed_layer_0 = =round(speed_print * 30 / 50)
+speed_print = 25
+speed_topbottom = 20
+speed_travel = 150
+speed_wall_0 = 20
+speed_wall_x = 25
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_line_distance = 2.85
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.22
+top_bottom_thickness = 0.75
+wall_thickness = 1.14
 

resources/quality/ultimaker2_plus/um2p_cpep_0.6_normal.inst.cfg

@@ -11,37 +11,37 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_xy_distance = 0.6
-speed_travel = 150
-support_z_distance = 0.22
-speed_wall_x = 35
-cool_min_speed = 8
-cool_fan_speed = 45
-raft_surface_thickness = 0.2
-raft_surface_line_width = 0.57
-raft_interface_line_spacing = 1.4
-raft_margin = 15
-speed_layer_0 = 30
-raft_airgap = 0.37
-infill_overlap = 5
-layer_height = 0.22
-raft_base_line_spacing = 2.4
-raft_interface_line_width = 1.2
-speed_wall_0 = 30
-cool_fan_speed_min = =cool_fan_speed * 25 / 45
-wall_thickness = 1.14
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-infill_sparse_density = 35
-top_bottom_thickness = 0.75
 adhesion_type = raft
-line_width = 0.57
+cool_fan_speed = 45
-layer_0_z_overlap = 0.22
+cool_fan_speed_min = =cool_fan_speed * 25 / 45
-raft_base_line_width = 1.2
-speed_print = 35
-support_line_distance = 2.85
-support_angle = 45
 cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
+infill_sparse_density = 35
+layer_0_z_overlap = 0.22
+layer_height = 0.22
+line_width = 0.57
+raft_airgap = 0.37
+raft_base_line_spacing = 2.4
+raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.57
+raft_surface_thickness = 0.2
+speed_layer_0 = 30
+speed_print = 35
+speed_topbottom = 20
+speed_travel = 150
+speed_wall_0 = 30
+speed_wall_x = 35
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_line_distance = 2.85
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.22
+top_bottom_thickness = 0.75
+wall_thickness = 1.14
 

resources/quality/ultimaker2_plus/um2p_cpep_0.8_draft.inst.cfg

@@ -11,32 +11,32 @@ quality_type = draft
 setting_version = 2
 
 [values]
-support_z_distance = 0.26
-speed_wall_x = 25
-cool_fan_speed = 50
-raft_surface_thickness = 0.2
-raft_surface_line_width = 0.7
-raft_interface_line_spacing = 1.8
-raft_airgap = 0.37
-infill_overlap = 5
-layer_height = 0.3
-raft_interface_line_width = 1.6
-top_bottom_thickness = 1.2
-cool_fan_speed_min = =cool_fan_speed * 25 / 50
-brim_line_count = 10
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 10
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+infill_overlap = 5
 infill_sparse_density = 40
 layer_0_z_overlap = 0.22
+layer_height = 0.3
+raft_airgap = 0.37
 raft_base_line_width = 1.6
-speed_print = 25
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
 speed_layer_0 = =round(speed_print * 30 / 25)
+speed_print = 25
+speed_topbottom = 20
 speed_wall_0 = 20
+speed_wall_x = 25
 support_angle = 45
-cool_min_layer_time = 3
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.2
 wall_thickness = 2.1
 

resources/quality/ultimaker2_plus/um2p_cpep_0.8_normal.inst.cfg

@@ -11,32 +11,32 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_z_distance = 0.26
-speed_wall_x = 30
-cool_fan_speed = 50
-raft_surface_thickness = 0.2
-raft_surface_line_width = 0.7
-raft_interface_line_spacing = 1.8
-raft_airgap = 0.37
-infill_overlap = 5
-layer_height = 0.2
-raft_interface_line_width = 1.6
-top_bottom_thickness = 1.2
-cool_fan_speed_min = =cool_fan_speed * 25 / 50
-brim_line_count = 10
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 10
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+infill_overlap = 5
 infill_sparse_density = 40
 layer_0_z_overlap = 0.22
+layer_height = 0.2
+raft_airgap = 0.37
 raft_base_line_width = 1.6
-speed_print = 30
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
 speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+speed_topbottom = 20
 speed_wall_0 = 20
+speed_wall_x = 30
 support_angle = 45
-cool_min_layer_time = 3
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.2
 wall_thickness = 2.1
 

resources/quality/ultimaker2_plus/um2p_nylon_0.25_high.inst.cfg

@@ -11,34 +11,34 @@ quality_type = high
 setting_version = 2
 
 [values]
-support_xy_distance = 0.6
-speed_travel = 150
-cool_fan_speed = 60
-support_z_distance = 0.45
-speed_wall_x = 40
-cool_min_speed = 15
-raft_surface_line_width = 0.2
-raft_interface_line_width = 0.5
-brim_line_count = 8
-raft_margin = 15
-speed_layer_0 = 30
-raft_airgap = 0.15
-infill_overlap = 5
-layer_height = 0.06
-raft_interface_line_spacing = 0.7
-speed_support = 40
-top_bottom_thickness = 1.2
-cool_fan_speed_min = =cool_fan_speed * 35 / 60
-wall_thickness = 1
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 35
-support_enable = True
-retraction_hop_enabled = 0.2
-speed_wall_0 = 20
 adhesion_type = raft
+brim_line_count = 8
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 25
 layer_0_z_overlap = 0.1
+layer_height = 0.06
+raft_airgap = 0.15
 raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = 30
 speed_print = 40
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 20
+speed_wall_x = 40
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.45
+top_bottom_thickness = 1.2
+wall_thickness = 1
 

resources/quality/ultimaker2_plus/um2p_nylon_0.25_normal.inst.cfg

@@ -11,34 +11,34 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_xy_distance = 0.6
-speed_travel = 150
-cool_fan_speed = 60
-support_z_distance = 0.45
-speed_wall_x = 40
-cool_min_speed = 15
-raft_surface_line_width = 0.2
-raft_interface_line_width = 0.5
-brim_line_count = 8
-raft_margin = 15
-speed_layer_0 = 30
-raft_airgap = 0.15
-infill_overlap = 5
-layer_height = 0.1
-raft_interface_line_spacing = 0.7
-speed_support = 40
-top_bottom_thickness = 1.2
-cool_fan_speed_min = =cool_fan_speed * 35 / 60
-wall_thickness = 1
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 35
-support_enable = True
-retraction_hop_enabled = 0.2
-speed_wall_0 = 20
 adhesion_type = raft
+brim_line_count = 8
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 25
 layer_0_z_overlap = 0.1
+layer_height = 0.1
+raft_airgap = 0.15
 raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = 30
 speed_print = 40
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 20
+speed_wall_x = 40
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.45
+top_bottom_thickness = 1.2
+wall_thickness = 1
 

resources/quality/ultimaker2_plus/um2p_nylon_0.4_fast.inst.cfg

@@ -11,33 +11,33 @@ quality_type = fast
 setting_version = 2
 
 [values]
-support_xy_distance = 0.6
-speed_travel = 150
-support_z_distance = 0.45
-raft_interface_line_spacing = 1
-cool_min_speed = 15
-raft_surface_thickness = 0.15
-raft_surface_line_width = 0.5
-speed_layer_0 = 30
-raft_airgap = 0.57
-infill_overlap = 5
-layer_height = 0.2
-raft_interface_line_width = 0.8
-top_bottom_thickness = 0.75
-cool_fan_speed_min = =cool_fan_speed * 0.35
-wall_thickness = 1.06
-support_pattern = lines
-support_infill_rate = 25
-speed_topbottom = 20
-support_enable = True
-speed_wall = 40
-raft_margin = 15
 adhesion_type = raft
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_layer_time = 3
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 30
 layer_0_z_overlap = 0.22
+layer_height = 0.2
+raft_airgap = 0.57
 raft_base_line_spacing = 1.6
-speed_print = 45
-support_angle = 45
-cool_min_layer_time = 3
 raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.5
+raft_surface_thickness = 0.15
+speed_layer_0 = 30
+speed_print = 45
+speed_topbottom = 20
+speed_travel = 150
+speed_wall = 40
+support_angle = 45
+support_enable = True
+support_infill_rate = 25
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.45
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
 

resources/quality/ultimaker2_plus/um2p_nylon_0.4_normal.inst.cfg

@@ -11,32 +11,32 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_xy_distance = 0.6
-speed_travel = 150
-support_z_distance = 0.45
-raft_interface_line_spacing = 1
-cool_min_speed = 15
-raft_surface_thickness = 0.15
-raft_surface_line_width = 0.5
-speed_layer_0 = 30
-raft_airgap = 0.57
-infill_overlap = 5
-layer_height = 0.15
-raft_interface_line_width = 0.8
-top_bottom_thickness = 0.75
-cool_fan_speed_min = =cool_fan_speed * 0.35
-wall_thickness = 1.06
-support_pattern = lines
-support_infill_rate = 25
-support_enable = True
-speed_wall = 40
-raft_margin = 15
 adhesion_type = raft
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_layer_time = 3
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 30
 layer_0_z_overlap = 0.22
+layer_height = 0.15
+raft_airgap = 0.57
 raft_base_line_spacing = 1.6
-speed_print = 45
-support_angle = 45
-cool_min_layer_time = 3
 raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+raft_surface_line_width = 0.5
+raft_surface_thickness = 0.15
+speed_layer_0 = 30
+speed_print = 45
+speed_travel = 150
+speed_wall = 40
+support_angle = 45
+support_enable = True
+support_infill_rate = 25
+support_pattern = lines
+support_xy_distance = 0.6
+support_z_distance = 0.45
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
 

resources/quality/ultimaker2_plus/um2p_nylon_0.6_fast.inst.cfg

@@ -11,37 +11,37 @@ quality_type = fast
 setting_version = 2
 
 [values]
-support_xy_distance = 0.7
-speed_travel = 150
-speed_wall_x = 40
-cool_min_speed = 15
-support_top_distance = 0.55
-raft_surface_line_width = 0.6
-raft_surface_thickness = 0.15
-brim_line_count = 8
-speed_layer_0 = 30
-raft_interface_line_spacing = 1.4
-infill_overlap = 5
-layer_height = 0.3
-raft_interface_line_width = 1.2
-speed_support = 40
-speed_wall_0 = 15
-cool_fan_speed_min = =cool_fan_speed * 0.35
-wall_thickness = 1.2
-support_pattern = lines
-support_infill_rate = 25
-speed_topbottom = 35
-support_enable = True
-retraction_hop_enabled = 0.2
-support_bottom_distance = 0.55
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 35
 layer_0_z_overlap = 0.22
-top_bottom_thickness = 1.2
+layer_height = 0.3
-speed_print = 55
 raft_airgap = 0.44
-support_angle = 45
 raft_base_line_spacing = 2.4
 raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+retraction_hop_enabled = 0.2
+speed_layer_0 = 30
+speed_print = 55
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 15
+speed_wall_x = 40
+support_angle = 45
+support_bottom_distance = 0.55
+support_enable = True
+support_infill_rate = 25
+support_pattern = lines
+support_top_distance = 0.55
+support_xy_distance = 0.7
+top_bottom_thickness = 1.2
+wall_thickness = 1.2
 

resources/quality/ultimaker2_plus/um2p_nylon_0.6_normal.inst.cfg

@@ -11,36 +11,36 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_xy_distance = 0.7
-speed_travel = 150
-support_z_distance = 0.55
-speed_wall_x = 40
-cool_min_speed = 15
-raft_surface_line_width = 0.6
-raft_surface_thickness = 0.15
-brim_line_count = 8
-speed_layer_0 = 30
-raft_interface_line_spacing = 1.4
-infill_overlap = 5
-layer_height = 0.15
-raft_interface_line_width = 1.2
-speed_support = 40
-speed_wall_0 = 15
-cool_fan_speed_min = =cool_fan_speed * 0.35
-wall_thickness = 1.2
-support_pattern = lines
-support_infill_rate = 25
-speed_topbottom = 35
-support_enable = True
-retraction_hop_enabled = 0.2
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 35
 layer_0_z_overlap = 0.22
-top_bottom_thickness = 1.2
+layer_height = 0.15
-speed_print = 55
 raft_airgap = 0.44
-support_angle = 45
 raft_base_line_spacing = 2.4
 raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+retraction_hop_enabled = 0.2
+speed_layer_0 = 30
+speed_print = 55
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 15
+speed_wall_x = 40
+support_angle = 45
+support_enable = True
+support_infill_rate = 25
+support_pattern = lines
+support_xy_distance = 0.7
+support_z_distance = 0.55
+top_bottom_thickness = 1.2
+wall_thickness = 1.2
 

resources/quality/ultimaker2_plus/um2p_nylon_0.8_draft.inst.cfg

@@ -11,37 +11,37 @@ quality_type = draft
 setting_version = 2
 
 [values]
-support_xy_distance = 0.75
-speed_travel = 150
-support_z_distance = 0.5
-speed_wall_x = 40
-cool_min_speed = 15
-brim_line_count = 8
-support_top_distance = 0.5
-raft_surface_thickness = 0.2
-wall_thickness = 2.4
-raft_margin = 15
-speed_layer_0 = 30
-raft_airgap = 0.44
-infill_overlap = 5
-layer_height = 0.3
-raft_interface_line_width = 1.6
-speed_support = 40
-speed_wall_0 = 15
-cool_fan_speed_min = =cool_fan_speed * 0.35
-raft_surface_line_width = 0.7
-support_pattern = lines
-support_infill_rate = 25
-speed_topbottom = 35
-support_enable = True
-retraction_hop_enabled = 0.2
-support_bottom_distance = 0.65
-top_bottom_thickness = 1.2
 adhesion_type = raft
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 40
 layer_0_z_overlap = 0.25
+layer_height = 0.3
+raft_airgap = 0.44
 raft_base_line_width = 1.6
-speed_print = 55
-support_angle = 45
 raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = 30
+speed_print = 55
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 15
+speed_wall_x = 40
+support_angle = 45
+support_bottom_distance = 0.65
+support_enable = True
+support_infill_rate = 25
+support_pattern = lines
+support_top_distance = 0.5
+support_xy_distance = 0.75
+support_z_distance = 0.5
+top_bottom_thickness = 1.2
+wall_thickness = 2.4
 

resources/quality/ultimaker2_plus/um2p_nylon_0.8_normal.inst.cfg

@@ -11,37 +11,37 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_xy_distance = 0.75
-speed_travel = 150
-support_z_distance = 0.5
-speed_wall_x = 40
-cool_min_speed = 15
-brim_line_count = 8
-support_top_distance = 0.5
-raft_surface_thickness = 0.2
-wall_thickness = 2.4
-raft_margin = 15
-raft_airgap = 0.44
-infill_overlap = 5
-layer_height = 0.2
-raft_interface_line_width = 1.6
-speed_support = 40
-speed_wall_0 = 15
-cool_fan_speed_min = =cool_fan_speed * 0.35
-raft_surface_line_width = 0.7
-support_pattern = lines
-support_infill_rate = 25
-speed_topbottom = 35
-support_enable = True
-retraction_hop_enabled = 0.2
-support_bottom_distance = 0.65
-top_bottom_thickness = 1.2
 adhesion_type = raft
+brim_line_count = 8
+cool_fan_speed_min = =cool_fan_speed * 0.35
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 40
 layer_0_z_overlap = 0.25
+layer_height = 0.2
+raft_airgap = 0.44
 raft_base_line_width = 1.6
-speed_print = 55
-speed_layer_0 = =round(speed_print * 30 / 55)
-support_angle = 45
 raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
+retraction_hop_enabled = 0.2
+speed_layer_0 = =round(speed_print * 30 / 55)
+speed_print = 55
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 15
+speed_wall_x = 40
+support_angle = 45
+support_bottom_distance = 0.65
+support_enable = True
+support_infill_rate = 25
+support_pattern = lines
+support_top_distance = 0.5
+support_xy_distance = 0.75
+support_z_distance = 0.5
+top_bottom_thickness = 1.2
+wall_thickness = 2.4
 

resources/quality/ultimaker2_plus/um2p_pc_0.25_high.inst.cfg

@@ -11,27 +11,28 @@ quality_type = high
 setting_version = 2
 
 [values]
-support_z_distance = 0.19
-raft_interface_line_spacing = 0.7
-cool_min_speed = 15
-cool_fan_speed = 50
-raft_surface_line_width = 0.2
-wall_thickness = 0.88
-raft_airgap = 0.25
-infill_overlap = 5
-layer_height = 0.06
-raft_interface_line_width = 0.5
-cool_fan_speed_min = 0
-brim_line_count = 32
-support_pattern = lines
-support_infill_rate = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 32
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 2
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 25
 layer_0_z_overlap = 0.2
-cool_min_layer_time = 2
+layer_height = 0.06
-speed_print = 30
+raft_airgap = 0.25
-speed_layer_0 = =round(speed_print * 30 / 30)
 raft_base_line_spacing = 1
 raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 0.88
+

resources/quality/ultimaker2_plus/um2p_pc_0.25_normal.inst.cfg

@@ -11,27 +11,28 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_z_distance = 0.19
-raft_interface_line_spacing = 0.7
-cool_min_speed = 15
-cool_fan_speed = 50
-raft_surface_line_width = 0.2
-wall_thickness = 0.88
-raft_airgap = 0.25
-infill_overlap = 5
-layer_height = 0.1
-raft_interface_line_width = 0.5
-cool_fan_speed_min = 0
-brim_line_count = 32
-support_pattern = lines
-support_infill_rate = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 32
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 2
+cool_min_speed = 15
+infill_overlap = 5
 infill_sparse_density = 25
 layer_0_z_overlap = 0.2
-cool_min_layer_time = 2
+layer_height = 0.1
-speed_print = 30
+raft_airgap = 0.25
-speed_layer_0 = =round(speed_print * 30 / 30)
 raft_base_line_spacing = 1
-raft_base_line_width = 0.5
+raft_base_line_width = 0.5
+raft_interface_line_spacing = 0.7
+raft_interface_line_width = 0.5
+raft_margin = 15
+raft_surface_line_width = 0.2
+speed_layer_0 = =round(speed_print * 30 / 30)
+speed_print = 30
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 0.88
+

resources/quality/ultimaker2_plus/um2p_pc_0.4_fast.inst.cfg

@@ -11,28 +11,29 @@ quality_type = fast
 setting_version = 2
 
 [values]
-speed_wall_x = 30
-support_z_distance = 0.19
-raft_airgap = 0.35
-cool_min_speed = 8
-cool_fan_speed = 50
-raft_interface_line_spacing = 1
-infill_overlap = 5
-layer_height = 0.2
-raft_interface_line_width = 0.8
-speed_wall_0 = 20
-cool_fan_speed_min = 0
-wall_thickness = 1.2
-support_pattern = lines
-support_infill_rate = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
 infill_sparse_density = 30
 layer_0_z_overlap = 0.3
-cool_min_layer_time = 3
+layer_height = 0.2
-speed_print = 45
+raft_airgap = 0.35
-speed_layer_0 = =round(speed_print * 30 / 45)
-support_angle = 45
 raft_base_line_spacing = 1.6
-raft_base_line_width = 0.8
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall_0 = 20
+speed_wall_x = 30
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 1.2
+

resources/quality/ultimaker2_plus/um2p_pc_0.4_normal.inst.cfg

@@ -11,28 +11,29 @@ quality_type = normal
 setting_version = 2
 
 [values]
-speed_wall_x = 30
-support_z_distance = 0.19
-raft_airgap = 0.35
-cool_min_speed = 8
-cool_fan_speed = 50
-raft_interface_line_spacing = 1
-infill_overlap = 5
-layer_height = 0.1
-raft_interface_line_width = 0.8
-speed_wall_0 = 20
-cool_fan_speed_min = 0
-wall_thickness = 1.2
-support_pattern = lines
-support_infill_rate = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
 infill_sparse_density = 30
 layer_0_z_overlap = 0.3
-cool_min_layer_time = 3
+layer_height = 0.1
-speed_print = 45
+raft_airgap = 0.35
-speed_layer_0 = =round(speed_print * 30 / 45)
-support_angle = 45
 raft_base_line_spacing = 1.6
-raft_base_line_width = 0.8
+raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.8
+raft_margin = 15
+speed_layer_0 = =round(speed_print * 30 / 45)
+speed_print = 45
+speed_wall_0 = 20
+speed_wall_x = 30
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.19
+wall_thickness = 1.2
+

resources/quality/ultimaker2_plus/um2p_pc_0.6_fast.inst.cfg

@@ -11,35 +11,35 @@ quality_type = fast
 setting_version = 2
 
 [values]
-speed_travel = 150
-support_z_distance = 0.21
-speed_wall_x = 40
-cool_min_speed = 8
-cool_fan_speed = 50
-raft_surface_thickness = 0.15
-raft_surface_line_width = 0.6
-raft_interface_line_spacing = 1.4
-speed_layer_0 = 30
-raft_airgap = 0.52
-infill_overlap = 5
-layer_height = 0.3
-raft_interface_line_width = 1.2
-raft_margin = 15
-cool_fan_speed_min = 0
-wall_thickness = 1.06
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-top_bottom_thickness = 0.75
 adhesion_type = raft
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
 infill_sparse_density = 35
 layer_0_z_overlap = 0.22
+layer_height = 0.3
+raft_airgap = 0.52
 raft_base_line_spacing = 2.4
-speed_print = 45
-support_line_distance = 3.5333
-speed_wall_0 = 30
-support_angle = 45
-cool_min_layer_time = 3
 raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+speed_layer_0 = 30
+speed_print = 45
+speed_topbottom = 20
+speed_travel = 150
+speed_wall_0 = 30
+speed_wall_x = 40
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_line_distance = 3.5333
+support_pattern = lines
+support_z_distance = 0.21
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
 

resources/quality/ultimaker2_plus/um2p_pc_0.6_normal.inst.cfg

@@ -11,35 +11,35 @@ quality_type = normal
 setting_version = 2
 
 [values]
-speed_travel = 150
-support_z_distance = 0.21
-speed_wall_x = 40
-cool_min_speed = 8
-cool_fan_speed = 50
-raft_surface_thickness = 0.15
-raft_surface_line_width = 0.6
-raft_interface_line_spacing = 1.4
-speed_layer_0 = 30
-raft_airgap = 0.52
-infill_overlap = 5
-layer_height = 0.15
-raft_interface_line_width = 1.2
-raft_margin = 15
-cool_fan_speed_min = 0
-wall_thickness = 1.06
-support_pattern = lines
-support_infill_rate = 20
-speed_topbottom = 20
-support_enable = True
-top_bottom_thickness = 0.75
 adhesion_type = raft
+cool_fan_speed = 50
+cool_fan_speed_min = 0
+cool_min_layer_time = 3
+cool_min_speed = 8
+infill_overlap = 5
 infill_sparse_density = 35
 layer_0_z_overlap = 0.22
+layer_height = 0.15
+raft_airgap = 0.52
 raft_base_line_spacing = 2.4
-speed_print = 45
-support_line_distance = 3.5333
-speed_wall_0 = 30
-support_angle = 45
-cool_min_layer_time = 3
 raft_base_line_width = 1.2
+raft_interface_line_spacing = 1.4
+raft_interface_line_width = 1.2
+raft_margin = 15
+raft_surface_line_width = 0.6
+raft_surface_thickness = 0.15
+speed_layer_0 = 30
+speed_print = 45
+speed_topbottom = 20
+speed_travel = 150
+speed_wall_0 = 30
+speed_wall_x = 40
+support_angle = 45
+support_enable = True
+support_infill_rate = 20
+support_line_distance = 3.5333
+support_pattern = lines
+support_z_distance = 0.21
+top_bottom_thickness = 0.75
+wall_thickness = 1.06
 

resources/quality/ultimaker2_plus/um2p_pc_0.8_draft.inst.cfg

@@ -11,29 +11,29 @@ quality_type = draft
 setting_version = 2
 
 [values]
-support_z_distance = 0.26
-raft_airgap = 0.47
-cool_fan_speed = 50
-raft_surface_line_width = 0.7
-raft_surface_thickness = 0.2
-brim_line_count = 10
-raft_interface_line_spacing = 1.8
-infill_overlap = 5
-layer_height = 0.5
-raft_interface_line_width = 1.6
-top_bottom_thickness = 2.0
-cool_fan_speed_min = =cool_fan_speed * 25 / 50
-wall_thickness = 2.1
-support_pattern = lines
-support_infill_rate = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 10
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+infill_overlap = 5
 infill_sparse_density = 40
 layer_0_z_overlap = 0.22
+layer_height = 0.5
+raft_airgap = 0.47
 raft_base_line_width = 1.6
-speed_print = 40
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
 speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
 support_angle = 45
-cool_min_layer_time = 3
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 2.0
+wall_thickness = 2.1
 

resources/quality/ultimaker2_plus/um2p_pc_0.8_normal.inst.cfg

@@ -11,29 +11,29 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_z_distance = 0.26
-raft_airgap = 0.47
-cool_fan_speed = 50
-raft_surface_line_width = 0.7
-raft_surface_thickness = 0.2
-brim_line_count = 10
-raft_interface_line_spacing = 1.8
-infill_overlap = 5
-layer_height = 0.2
-raft_interface_line_width = 1.6
-top_bottom_thickness = 1.2
-cool_fan_speed_min = =cool_fan_speed * 25 / 50
-wall_thickness = 2.1
-support_pattern = lines
-support_infill_rate = 20
-support_enable = True
-raft_margin = 15
 adhesion_type = raft
+brim_line_count = 10
+cool_fan_speed = 50
+cool_fan_speed_min = =cool_fan_speed * 25 / 50
+cool_min_layer_time = 3
+infill_overlap = 5
 infill_sparse_density = 40
 layer_0_z_overlap = 0.22
+layer_height = 0.2
+raft_airgap = 0.47
 raft_base_line_width = 1.6
-speed_print = 40
+raft_interface_line_spacing = 1.8
+raft_interface_line_width = 1.6
+raft_margin = 15
+raft_surface_line_width = 0.7
+raft_surface_thickness = 0.2
 speed_layer_0 = =round(speed_print * 30 / 40)
+speed_print = 40
 support_angle = 45
-cool_min_layer_time = 3
+support_enable = True
+support_infill_rate = 20
+support_pattern = lines
+support_z_distance = 0.26
+top_bottom_thickness = 1.2
+wall_thickness = 2.1
 

resources/quality/ultimaker2_plus/um2p_pp_0.25_normal.inst.cfg

@@ -12,3 +12,4 @@ setting_version = 2
 supported = False
 
 [values]
+

resources/quality/ultimaker2_plus/um2p_pp_0.4_fast.inst.cfg

@@ -70,4 +70,5 @@ switch_extruder_retraction_speeds = 35
 travel_avoid_distance = 3
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.38 / 0.38, 2)
-wall_thickness = 0.76
+wall_thickness = 0.76
+

resources/quality/ultimaker2_plus/um2p_pp_0.4_normal.inst.cfg

@@ -69,4 +69,5 @@ switch_extruder_retraction_speeds = 35
 travel_avoid_distance = 3
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.38 / 0.38, 2)
-wall_thickness = 0.76
+wall_thickness = 0.76
+

resources/quality/ultimaker2_plus/um2p_pp_0.6_draft.inst.cfg

@@ -72,4 +72,5 @@ top_bottom_thickness = 1.1
 travel_avoid_distance = 3
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.57 / 0.57, 2)
-wall_thickness = 1.14
+wall_thickness = 1.14
+

resources/quality/ultimaker2_plus/um2p_pp_0.6_fast.inst.cfg

@@ -72,4 +72,5 @@ top_bottom_thickness = 1.1
 travel_avoid_distance = 3
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.57 / 0.57, 2)
-wall_thickness = 1.14
+wall_thickness = 1.14
+

resources/quality/ultimaker2_plus/um2p_pp_0.8_draft.inst.cfg

@@ -72,4 +72,5 @@ top_bottom_thickness = 1.5
 travel_avoid_distance = 3
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.76 / 0.76, 2)
-wall_thickness = 1.52
+wall_thickness = 1.52
+

resources/quality/ultimaker2_plus/um2p_pp_0.8_verydraft.inst.cfg

@@ -72,4 +72,5 @@ top_bottom_thickness = 1.5
 travel_avoid_distance = 3
 wall_0_inset = 0
 wall_line_width_x = =round(line_width * 0.76 / 0.76, 2)
-wall_thickness = 1.52
+wall_thickness = 1.52
+

resources/quality/ultimaker2_plus/um2p_tpu_0.25_high.inst.cfg

@@ -11,33 +11,33 @@ quality_type = high
 setting_version = 2
 
 [values]
-support_xy_distance = 0.6
+adhesion_type = brim
-cool_min_speed = 15
+brim_line_count = 8
-support_infill_rate = 25
+cool_fan_speed = 60
-speed_wall_0 = 15
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
-layer_0_z_overlap = 0.1
 cool_min_layer_time = 7
+cool_min_speed = 15
+infill_sparse_density = 10
+layer_0_z_overlap = 0.1
+layer_height = 0.06
+raft_airgap = 0.2
+raft_base_line_spacing = 1
+raft_interface_line_spacing = 1
+raft_interface_line_width = 0.2
+raft_surface_line_width = 0.2
+retraction_hop_enabled = 0.2
 speed_layer_0 = 30
 speed_print = 40
-wall_thickness = 0.88
-support_enable = True
-speed_topbottom = 35
-raft_surface_line_width = 0.2
-raft_base_line_spacing = 1
-top_bottom_thickness = 1.2
-layer_height = 0.06
-support_angle = 45
-infill_sparse_density = 10
-cool_fan_speed = 60
-speed_travel = 150
 speed_support = 40
-support_z_distance = =layer_height * 2
+speed_topbottom = 35
-cool_fan_speed_min = =cool_fan_speed * 35 / 60
+speed_travel = 150
-brim_line_count = 8
+speed_wall_0 = 15
-retraction_hop_enabled = 0.2
 speed_wall_x = 38
-raft_airgap = 0.2
+support_angle = 45
-raft_interface_line_spacing = 1
+support_enable = True
-adhesion_type = brim
+support_infill_rate = 25
-raft_interface_line_width = 0.2
+support_xy_distance = 0.6
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 0.88
 

resources/quality/ultimaker2_plus/um2p_tpu_0.4_normal.inst.cfg

@@ -11,29 +11,30 @@ quality_type = normal
 setting_version = 2
 
 [values]
-support_xy_distance = 0.65
-speed_travel = 150
-support_z_distance = =layer_height * 2
-speed_wall_x = 35
-cool_min_speed = 15
-cool_fan_speed = 60
-retraction_hop_enabled = 0.2
-brim_line_count = 8
-speed_layer_0 = 30
-raft_interface_line_spacing = 1
-raft_base_line_spacing = 2
-speed_support = 40
-raft_margin = 12
-cool_fan_speed_min = =cool_fan_speed * 35 / 60
-wall_thickness = 1.05
-support_infill_rate = 25
-speed_topbottom = 35
-support_enable = True
-speed_wall_0 = 20
 adhesion_type = brim
-infill_sparse_density = 10
+brim_line_count = 8
-top_bottom_thickness = 1.2
+cool_fan_speed = 60
-speed_print = 40
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
-support_angle = 45
 cool_min_layer_time = 10
+cool_min_speed = 15
+infill_sparse_density = 10
+raft_base_line_spacing = 2
 raft_base_line_width = 0.8
+raft_interface_line_spacing = 1
+raft_margin = 12
+retraction_hop_enabled = 0.2
+speed_layer_0 = 30
+speed_print = 40
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 20
+speed_wall_x = 35
+support_angle = 45
+support_enable = True
+support_infill_rate = 25
+support_xy_distance = 0.65
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1.05
+

resources/quality/ultimaker2_plus/um2p_tpu_0.6_fast.inst.cfg

@@ -11,35 +11,35 @@ quality_type = fast
 setting_version = 2
 
 [values]
-support_xy_distance = 0.7
-raft_base_line_width = 0.6
-cool_min_speed = 15
-line_width = 0.57
-support_infill_rate = 25
-speed_wall_0 = 15
-wall_thickness = 1.14
-raft_base_line_spacing = 1.2
-speed_layer_0 = 30
-raft_margin = 15
-speed_travel = 150
-raft_surface_line_width = 0.5
-layer_height = 0.12
-raft_interface_line_width = 0.57
-speed_print = 45
-top_bottom_thickness = 1.2
-speed_topbottom = 35
-layer_0_z_overlap = 0.12
-support_angle = 45
-infill_sparse_density = 10
-cool_fan_speed = 60
-speed_support = 40
-support_z_distance = =layer_height * 2
-cool_fan_speed_min = =cool_fan_speed * 35 / 60
-brim_line_count = 8
-retraction_hop_enabled = 0.2
-speed_wall_x = 40
-support_enable = True
-raft_interface_line_spacing = 1.2
 adhesion_type = brim
+brim_line_count = 8
+cool_fan_speed = 60
+cool_fan_speed_min = =cool_fan_speed * 35 / 60
+cool_min_speed = 15
+infill_sparse_density = 10
+layer_0_z_overlap = 0.12
+layer_height = 0.12
+line_width = 0.57
 raft_airgap = 0.24
+raft_base_line_spacing = 1.2
+raft_base_line_width = 0.6
+raft_interface_line_spacing = 1.2
+raft_interface_line_width = 0.57
+raft_margin = 15
+raft_surface_line_width = 0.5
+retraction_hop_enabled = 0.2
+speed_layer_0 = 30
+speed_print = 45
+speed_support = 40
+speed_topbottom = 35
+speed_travel = 150
+speed_wall_0 = 15
+speed_wall_x = 40
+support_angle = 45
+support_enable = True
+support_infill_rate = 25
+support_xy_distance = 0.7
+support_z_distance = =layer_height * 2
+top_bottom_thickness = 1.2
+wall_thickness = 1.14