removed accidental temp files

resources/definitions/Zyyx plus start gcode.txt

@@ -1 +0,0 @@
-; ZYYX+ start gcode\n; Author Theodor Hansson 2024\nM73 P0; enable build progress\nM104 S{material_print_temperature_layer_0} T0; set nozzle temperature\nM126 S0; Turn off fan\nG21; set units to mm\nG90; set positioning to absolute\nG130 X80 Y80 Z127 A127 B127 ; Set Stepper Vref to default value\n\n; Home xy-axis\nG162 X Y F2500; home XY axes maximum\nG92 X0 Y0\nG1 X-5 Y-5 F2500\nG162 X Y F200; home XY axes maximum slowly\nG92 X132.5 Y120\n\n; Home z-axis\nG161 Z F1100; home Z axis minimum\nG92 Z0\nG1 Z2 F1100\nG161 Z F100; home Z axis minimum slowly\nG92 Z0\nM132 Z; Recall home offsets for Z\n\n; Calibrate point 1 (we're already at point 1)\nM131 A; store surface calibration point 1\nG1 Z2 F1100; back up from buildplate\n\n; Calibrate point 2\nG1 X-44.5 Y120 F9000; move to 2nd probing point\nG161 Z F100\nM131 B; store surface calibration point 1\nG1 Z2 F1100; back up from buildplate\n\n; Calibrate point 3\nG1 X132.5 Y-110 F9000; move to 2nd probing point\nG161 Z F100\nM131 AB; store surface calibration point 3\nG1 Z2 F1100; back up from buildplate\nM132 AB; Activate auto-leveling\nG1 Z1 F1000\n\n; Lay prime strip\nM133 T0 P300; stabilize extruder temperature (abort after 5 mins)\nM126 S{cool_fan_speed_0}; Activate fan\nG4 P1000; Wait a little bit longer\nG1 X100 Y-110 Z0.2 F1000\nG1 X40 E9 F1000\nG1 X0 E12.5 F1000\nG92 E0 ; Set E to 0\n\n; End of start gcode

resources/definitions/Zyyx pro start gcode legacy.txt

@@ -1,60 +0,0 @@
-;start of ZYYX Pro startcode
-M73 P0; enable build progress
-G21; set units to mm
-G90; set positioning to absolute
-G130 X80 Y80 A127 B127 ; Set Stepper Vref to default value
-G162 X Y F3000; home XY axes maximum
-G161 Z F450
-G161 Z F450; home Z axis minimum
-G92 X0 Y0 Z0 E0
-G1 X0 Y0 Z20 F3000
-G1 X-120 Y-110 Z10 F3000
-G130 X0 Y0 Z3 A0 B0 ; Set Stepper Vref to low value
-M420 P10; set back fan speed 10 off 11-20 10-100%
-M140 S10 T0; set 100% heater power
-M140 S99 T0; set chamber heater negative hysteresis 19 degrees
-M140 S102 T0; set chamber heater positive hysteresis 2 degrees
-M140 S{material_bed_temperature_layer_0} T0; set chamber temperature
-M104 S100 T0; set extruder temp 100 while heating
-M134 T0; wait for heated chamber temperature
-M420 P13; set fan speed 10 off 11-20 10-100%
-G130 X80 Y80 Z64 A127 B127 ; Set Stepper Vref to default value
-; Perform probing of build plate
-G162 X Y F3000; home XY axes maximum
-G161 Z F450
-G161 Z F450; home Z axis minimum
-G92 X0 Y0 Z0 E0
-G1 X0 Y0 Z5 F200
-G161 Z F200; home Z axis minimum again
-G92 X0 Y0 Z0 E0
-M131 A; store surface calibration point 1
-G1 X0 Y0 Z5 F200
-G1 X-182 Y0 Z5 F3000; move to 2nd probing point
-G161 Z F200
-M131 B; store surface calibration point 2
-G92 X-182 Y0 Z0 E0
-G1 X-182 Y0 Z5 F200
-G1 X0 Y0 Z5 F3000; move to home point
-G161 Z F200; home Z axis minimum again
-G92 X0 Y0 Z0 E0; set reference again
-G1 X0 Y0 Z5 F200; clear Z
-G1 X0 Y-228 Z5 F3000; move to 3rd calibration point
-G161 Z F200
-M131 AB; store surface calibration point 3
-M132 AB; activate auto leveling
-G92 X0 Y-228 Z0 E0
-G1 X0 Y-228 Z5 F200
-G162 X Y F3000
-G161 Z F200
-G92 X135 Y115 Z0 E0
-M132 Z; Recall stored home offset for Z axis
-G1 X135 Y115 Z5 F450; clear nozzle from hole
-G1 X0 Y115 Z5 F3000; clear nozzle from hole
-; end of ZYYX pro build plate calibration
-M127; turn off fan
-M104 S{material_print_temperature_layer_0} T0
-M133 T0 ; stabilize extruder temperature
-;SET_ZXPARAM
-;SET_SUPPORT_BUMPMAP
-G92 E0 ; Set E to 0
-; end of ZYYX Pro start code

resources/definitions/Zyyx pro start gcode.txt

@@ -1,52 +0,0 @@
-;start of ZYYX Pro startcode
-M73 P0; enable build progress
-M420 P10; set back fan speed 10 off 11-20 10-100%
-M140 S10 T0; set 100% heater power
-M140 S99 T0; set chamber heater negative hysteresis 19 degrees
-M140 S102 T0; set chamber heater positive hysteresis 2 degrees
-M140 S60 T0; set chamber temperature
-M104 S{material_print_temperature_layer_0} T0; set nozzle temperature
-G21; set units to mm
-G90; set positioning to absolute
-G130 X80 Y90 A127 B127 ; Set Stepper Vref to default value
-; Start build plate homing
-G162 X Y F3000; home XY axes maximum
-G161 Z F1200; home Z axis minimum
-G92 X0 Y0 Z0 E0
-G1 X0 Y0 Z2 F2000
-G1 X-5 Y-5 Z2 F5000
-G162 X Y F300; home XY axes maximum
-G161 Z F200; home Z axis minimum
-G92 X0 Y0 Z0
-M131 A; store surface calibration point 1
-; Homing point 1 complete
-G1 X0 Y0 Z5 F3000; 
-G1 X-182 Y0 Z5 F10000; move to 2nd probing point
-G161 Z F200
-M131 B; store surface calibration point 2
-G92 X-182 Y0 Z0 E0
-G1 X-182 Y0 Z5 F10000
-; Homing point 2 complete
-G1 X0 Y-228 Z5 F8000; move to 3rd calibration point
-G161 Z F200
-M131 AB; store surface calibration point 3
-M132 AB; activate auto leveling
-; Homing point 2 complete
-G1 Z5 F3000
-G1 X-5 Y-5 F5000
-G162 X Y F300
-G1 Z5 F3000
-G161 Z F200
-G92 X135 Y115 Z0 E0
-M132 Z; Recall stored home offset for Z axis
-G1 Z10 F3000; clear nozzle from hole
-G1 X0 Y0 Z10 F8000; move to middle of plate
-; end of ZYYX pro build plate calibration
-M133 T0 ; stabilize extruder temperature
-M126; turn on fan to help heat chamber
-M134 T0; wait for heated chamber temperature
-M127; turn off fan when hot
-;SET_ZXPARAM
-;SET_SUPPORT_BUMPMAP
-G92 E0 ; Set E to 0
-; end of ZYYX Pro start code

resources/definitions/zyyx_testing.txt

@@ -1,51 +0,0 @@
-;RIGHT EXTRUDER
-; Replicator 1 dual start.gcode
-M73 P0 ; Enable build progress
-G21; set units to mm
-G90 ; absolute positioning
-G162 Z F3000 ; Home Z maximum
-G28 X Y ; Home X Y maximum
-G92 X0 Y0
-M140 S[bed0_temperature] T0 ; Heat buildplate
-M134 T0 ; Stabilize bed temperature
-M104 S180 T0 ; Heat right extruder
-M104 S70 T1 ; Heat lightly left extruder
-M133 T0 ; Stabilize right extruder temperature
-M133 T1 ; Stabilize left extruder temperature
-M104 S0 T1 ; cool down left extruder
-G0 X-45 Y-15; estrema destra in fondo punto di calibrazione ZERO prende offset primario di asse Z
-G161 Z F800
-G92 Z-5 ; Set Z to 5
-G4 P20000 ; 20 seconds wait, before beginning, to stabilize ambient temps
-G1 Z0
-G161 Z F50 ; Home Z maximum slowly
-M132 Z ; Recall home offsets for Z
-G1 Z10
-G28 X Y ; Home X Y maximum
-M132 X Y A B ; Recall home offsets for everything but Z
-G1 X-80 Y65 Z10 F2000 ; Prima posizione di calibrazione
-G161 Z F100
-M131 A ; prima posizione memorizzata
-G1 X100 Y-10 Z10 F2000 ; Seconda posizione di calibrazione
-G161 Z F100
-M131 B ; seconda posizione memorizzata
-G1 X-70 Y-10 Z10 F2000 ; Terza posizione di calibrazione
-G161 Z F100
-M131 AB ; Terza posizione memorizzata
-M132 AB ; avvio del livellamento automatico
-M135 T0 ; Load right extruder offsets
-G1 X-120 Y-75 Z30 F9000 ; Move to wait position off table
-G130 X20 Y20 Z20 A20 B20 ; Lower stepper Vrefs while heating
-M126 S[fan_speed_pwm] ; Set fan speed
-M104 S[extruder0_temperature] T0 ; Heat right extruder
-M133 T0 ; Stabilize right extruder temperature
-G130 X127 Y127 Z40 A127 B127 ; Default stepper Vrefs
-G92 A0 B0 ; Zero extruders
-G1 X100 Y-75 F9000 ; Move to front right corner of bed
-G1 Z0.4 F6000 ; Move down to purge
-G1 X-90 Y-75 E24 F2000 ; Extrude a line of filament across the front edge of the bed
-G1 X-100 Y-75 F180 ; Wait for ooze
-G1 X-110 Y-75 F5000 ; Fast wipe
-G1 Z0.2 F100 ; Lift
-M73 P1 ;@body (notify GPX body has started)
-; end of start.gcode