Merge pull request #14525 from Ultimaker/PP-71_53_avoid-small-layer-temperature-to-be-lower-then-minimum_value

PP-71 avoid small layer temperature to be lower than minimum value

resources/definitions/fdmprinter.def.json

@@ -4419,7 +4419,7 @@
                     "type": "float",
                     "value": "material_print_temperature",
                     "enabled": "cool_min_layer_time > 0",
-                    "minimum_value": "material_final_print_temperature",
+                    "minimum_value": "max(material_final_print_temperature, material_initial_print_temperature)",
                     "maximum_value": "material_print_temperature",
                     "settable_per_mesh": false,
                     "settable_per_extruder": true

resources/definitions/ultimaker.def.json

@@ -41,7 +41,7 @@
         "cool_min_layer_time": { "value": 6 },
         "cool_min_layer_time_fan_speed_max": { "value": "cool_min_layer_time + 5" },
         "cool_min_speed": { "value": "round(speed_wall_0 * 3 / 4) if cool_lift_head else round(speed_wall_0 / 5)" },
-        "cool_min_temperature": { "value": "material_print_temperature - 15" },
+        "cool_min_temperature": { "value": "max([material_final_print_temperature, material_initial_print_temperature, material_print_temperature - 15])" },
         "gradual_support_infill_step_height": { "value": "4 * layer_height" },
         "gradual_support_infill_steps": { "value": "2 if support_interface_enable else 0" },
         "infill_material_flow": { "value": "(1.95-infill_sparse_density / 100 if infill_sparse_density > 95 else 1) * material_flow" },

resources/definitions/ultimaker2_plus_connect.def.json

@@ -101,11 +101,6 @@
         "machine_width": { "default_value": 223 },
         "material_bed_temperature": { "maximum_value": 110 },
         "material_bed_temperature_layer_0": { "maximum_value": 110 },
-        "material_initial_print_temperature":
-        {
-            "maximum_value": 260,
-            "value": "material_print_temperature"
-        },
         "material_print_temperature": { "maximum_value": 260 },
         "material_print_temperature_layer_0": { "maximum_value": 260 },
         "meshfix_maximum_deviation": { "value": "(layer_height / 3) if magic_spiralize else (layer_height / 4)" },

resources/quality/ultimaker3/um3_aa0.25_PLA_Normal_Quality.inst.cfg

@@ -17,7 +17,6 @@ infill_overlap = =0 if infill_sparse_density > 80 else 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'grid'
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_heat_up_speed = 1.4
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = 190
 retraction_hop = 0.2
 skin_overlap = 5

resources/quality/ultimaker3/um3_aa0.25_PP_Normal_Quality.inst.cfg

@@ -14,12 +14,11 @@ weight = 0
 
 [values]
 brim_width = 10
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 5
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 15
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker3/um3_aa0.25_TPLA_Normal_Quality.inst.cfg

@@ -17,7 +17,6 @@ infill_overlap = =0 if infill_sparse_density > 80 else 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'grid'
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_heat_up_speed = 1.4
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = =default_material_print_temperature - 15
 skin_overlap = 5
 speed_print = 30

resources/quality/ultimaker3/um3_aa0.4_ABS_Draft_Print.inst.cfg

@@ -14,7 +14,6 @@ weight = -2
 [values]
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = False
 skin_overlap = 20

resources/quality/ultimaker3/um3_aa0.4_ABS_Fast_Print.inst.cfg

@@ -14,7 +14,6 @@ weight = -1
 [values]
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 prime_tower_enable = False
 speed_print = 60

resources/quality/ultimaker3/um3_aa0.4_ABS_High_Quality.inst.cfg

@@ -14,7 +14,6 @@ weight = 1
 [values]
 machine_nozzle_cool_down_speed = 0.8
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature - 5
 prime_tower_enable = False
 speed_print = 50

resources/quality/ultimaker3/um3_aa0.4_ABS_Normal_Quality.inst.cfg

@@ -14,7 +14,6 @@ weight = 0
 [values]
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 prime_tower_enable = False
 speed_print = 55
 speed_topbottom = =math.ceil(speed_print * 30 / 55)

resources/quality/ultimaker3/um3_aa0.4_CPEP_Draft_Print.inst.cfg

@@ -17,7 +17,6 @@ infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 infill_wipe_dist = 0
 layer_height = 0.2
 machine_min_cool_heat_time_window = 15
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker3/um3_aa0.4_CPEP_Fast_Print.inst.cfg

@@ -17,7 +17,6 @@ infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 infill_wipe_dist = 0
 layer_height = 0.15
 machine_min_cool_heat_time_window = 15
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker3/um3_aa0.4_CPEP_High_Quality.inst.cfg

@@ -19,7 +19,6 @@ layer_height = 0.06
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker3/um3_aa0.4_CPEP_Normal_Quality.inst.cfg

@@ -18,7 +18,6 @@ infill_wipe_dist = 0
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker3/um3_aa0.4_CPE_Draft_Print.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = -2
 
 [values]
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 skin_overlap = 20
 speed_print = 60

resources/quality/ultimaker3/um3_aa0.4_CPE_Fast_Print.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = -1
 
 [values]
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 speed_print = 60
 speed_topbottom = =math.ceil(speed_print * 30 / 60)

resources/quality/ultimaker3/um3_aa0.4_CPE_High_Quality.inst.cfg

@@ -14,7 +14,6 @@ weight = 1
 [values]
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature - 5
 speed_print = 50
 speed_topbottom = =math.ceil(speed_print * 30 / 50)

resources/quality/ultimaker3/um3_aa0.4_CPE_Normal_Quality.inst.cfg

@@ -14,7 +14,6 @@ weight = 0
 [values]
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 speed_print = 55
 speed_topbottom = =math.ceil(speed_print * 30 / 55)
 speed_wall = =math.ceil(speed_print * 30 / 55)

resources/quality/ultimaker3/um3_aa0.4_Nylon_Draft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 adhesion_type = brim
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 ooze_shield_angle = 40
 raft_airgap = 0.25

resources/quality/ultimaker3/um3_aa0.4_Nylon_Fast_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -1
 
 [values]
 adhesion_type = brim
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 ooze_shield_angle = 40
 raft_airgap = 0.25

resources/quality/ultimaker3/um3_aa0.4_Nylon_High_Quality.inst.cfg

@@ -13,7 +13,6 @@ weight = 1
 
 [values]
 adhesion_type = brim
-material_initial_print_temperature = =material_print_temperature - 5
 ooze_shield_angle = 40
 raft_airgap = 0.25
 skin_overlap = 50

resources/quality/ultimaker3/um3_aa0.4_Nylon_Normal_Quality.inst.cfg

@@ -13,7 +13,6 @@ weight = 0
 
 [values]
 adhesion_type = brim
-material_initial_print_temperature = =material_print_temperature - 5
 ooze_shield_angle = 40
 raft_airgap = 0.25
 skin_overlap = 50

resources/quality/ultimaker3/um3_aa0.4_PC_Draft_Print.inst.cfg

@@ -22,7 +22,6 @@ layer_height = 0.2
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40

resources/quality/ultimaker3/um3_aa0.4_PC_Fast_Print.inst.cfg

@@ -21,7 +21,6 @@ layer_height = 0.15
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40

resources/quality/ultimaker3/um3_aa0.4_PC_High_Quality.inst.cfg

@@ -22,7 +22,6 @@ layer_height = 0.06
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature - 10
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40

resources/quality/ultimaker3/um3_aa0.4_PC_Normal_Quality.inst.cfg

@@ -20,7 +20,6 @@ infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40
 prime_tower_enable = True

resources/quality/ultimaker3/um3_aa0.4_PETG_Draft_Print.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = -2
 
 [values]
-material_initial_print_temperature = =material_print_temperature
 material_print_temperature = =default_material_print_temperature + 5
 retraction_combing = all
 skin_overlap = 20

resources/quality/ultimaker3/um3_aa0.4_PETG_Fast_Print.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = -1
 
 [values]
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature
 retraction_combing = all
 speed_infill = =math.ceil(speed_print * 50 / 60)

resources/quality/ultimaker3/um3_aa0.4_PETG_Normal_Quality.inst.cfg

@@ -14,7 +14,6 @@ weight = 0
 [values]
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 5
 retraction_combing = all
 speed_infill = =math.ceil(speed_print * 45 / 55)

resources/quality/ultimaker3/um3_aa0.4_PP_Draft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 brim_width = 20
-cool_min_temperature = =material_print_temperature - 10
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
@@ -22,7 +21,7 @@ machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 5
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 5
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker3/um3_aa0.4_PP_Fast_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -1
 
 [values]
 brim_width = 20
-cool_min_temperature = =material_print_temperature - 10
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
@@ -21,8 +20,8 @@ layer_height = 0.15
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_final_print_temperature = =material_print_temperature - 12
+material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 2
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 13
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker3/um3_aa0.4_PP_Normal_Quality.inst.cfg

@@ -13,7 +13,6 @@ weight = 0
 
 [values]
 brim_width = 20
-cool_min_temperature = =material_print_temperature - 10
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
@@ -21,7 +20,7 @@ machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 5
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 15
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker3/um3_aa0.4_TPU_Draft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =5 * layer_height
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
@@ -25,7 +24,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0
 prime_tower_wipe_enabled = True

resources/quality/ultimaker3/um3_aa0.4_TPU_Fast_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -1
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =5 * layer_height
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
@@ -25,7 +24,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0
 prime_tower_wipe_enabled = True

resources/quality/ultimaker3/um3_aa0.4_TPU_Normal_Quality.inst.cfg

@@ -13,7 +13,6 @@ weight = 0
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =5 * layer_height
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
@@ -24,7 +23,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 multiple_mesh_overlap = 0
 prime_tower_wipe_enabled = True
 retraction_count_max = 15

resources/quality/ultimaker3/um3_aa0.8_PLA_Draft_Print.inst.cfg

@@ -16,7 +16,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker3/um3_aa0.8_PLA_Superdraft_Print.inst.cfg

@@ -17,7 +17,6 @@ infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 layer_height = 0.4
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = =default_material_print_temperature + 15
 prime_tower_enable = True
 speed_infill = =math.ceil(speed_print * 35 / 45)

resources/quality/ultimaker3/um3_aa0.8_PLA_Verydraft_Print.inst.cfg

@@ -17,7 +17,6 @@ infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 layer_height = 0.3
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker3/um3_aa0.8_PP_Draft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 brim_width = 25
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 material_print_temperature = =default_material_print_temperature - 2
 multiple_mesh_overlap = 0.2

resources/quality/ultimaker3/um3_aa0.8_PP_Superdraft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -4
 
 [values]
 brim_width = 25
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0.2

resources/quality/ultimaker3/um3_aa0.8_PP_Verydraft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -3
 
 [values]
 brim_width = 25
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 layer_height = 0.3
 multiple_mesh_overlap = 0.2

resources/quality/ultimaker3/um3_aa0.8_TPLA_Draft_Print.inst.cfg

@@ -16,7 +16,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cubic'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = =default_material_print_temperature + 0
 prime_tower_enable = False
 speed_print = 45

resources/quality/ultimaker3/um3_aa0.8_TPLA_Superdraft_Print.inst.cfg

@@ -16,7 +16,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cubic'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = =default_material_print_temperature + 5
 prime_tower_enable = False
 speed_infill = =math.ceil(speed_print * 30 / 30)

resources/quality/ultimaker3/um3_aa0.8_TPLA_Verydraft_Print.inst.cfg

@@ -16,7 +16,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cubic'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =max(-273.15, material_print_temperature - 10)
 material_print_temperature = =default_material_print_temperature + 5
 prime_tower_enable = False
 speed_infill = =math.ceil(speed_print * 30 / 35)

resources/quality/ultimaker3/um3_aa0.8_TPU_Draft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =4 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
 infill_sparse_density = 15
@@ -21,7 +20,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 105
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 2
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True

resources/quality/ultimaker3/um3_aa0.8_TPU_Superdraft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -4
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =4 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
 infill_sparse_density = 15
@@ -22,7 +21,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 105
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True

resources/quality/ultimaker3/um3_aa0.8_TPU_Verydraft_Print.inst.cfg

@@ -13,7 +13,6 @@ weight = -3
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =4 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
 infill_sparse_density = 15
@@ -22,7 +21,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 105
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True
 prime_tower_flow = 100

resources/quality/ultimaker_s3/um_s3_aa0.25_pla_0.1mm.inst.cfg

@@ -17,7 +17,6 @@ infill_overlap = =0 if infill_sparse_density > 80 else 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'grid'
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_heat_up_speed = 1.4
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = 190
 retraction_hop = 0.2
 skin_overlap = 5

resources/quality/ultimaker_s3/um_s3_aa0.25_pp_0.1mm.inst.cfg

@@ -14,12 +14,11 @@ weight = 0
 
 [values]
 brim_width = 10
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 5
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 15
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker_s3/um_s3_aa0.25_tough-pla_0.1mm.inst.cfg

@@ -17,7 +17,6 @@ infill_overlap = =0 if infill_sparse_density > 80 else 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'grid'
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_heat_up_speed = 1.4
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 15
 skin_overlap = 5
 speed_print = 30

resources/quality/ultimaker_s3/um_s3_aa0.4_abs_0.06mm.inst.cfg

@@ -15,7 +15,6 @@ weight = 1
 machine_nozzle_cool_down_speed = 0.8
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 20
-material_initial_print_temperature = =material_print_temperature - 15
 material_print_temperature = =default_material_print_temperature + 5
 prime_tower_enable = False
 raft_airgap = 0.15

resources/quality/ultimaker_s3/um_s3_aa0.4_abs_0.15mm.inst.cfg

@@ -15,7 +15,6 @@ weight = -1
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 20
-material_initial_print_temperature = =material_print_temperature - 15
 material_print_temperature = =default_material_print_temperature + 15
 prime_tower_enable = False
 raft_airgap = 0.15

resources/quality/ultimaker_s3/um_s3_aa0.4_abs_0.1mm.inst.cfg

@@ -15,7 +15,6 @@ weight = 0
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 20
-material_initial_print_temperature = =material_print_temperature - 15
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = False
 raft_airgap = 0.15

resources/quality/ultimaker_s3/um_s3_aa0.4_abs_0.2mm.inst.cfg

@@ -15,7 +15,6 @@ weight = -2
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 20
-material_initial_print_temperature = =material_print_temperature - 15
 material_print_temperature = =default_material_print_temperature + 20
 prime_tower_enable = False
 raft_airgap = 0.15

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe-plus_0.06mm.inst.cfg

@@ -17,7 +17,6 @@ infill_wipe_dist = 0
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe-plus_0.15mm.inst.cfg

@@ -15,7 +15,6 @@ weight = -1
 infill_overlap = 0
 infill_wipe_dist = 0
 machine_min_cool_heat_time_window = 15
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe-plus_0.1mm.inst.cfg

@@ -17,7 +17,6 @@ infill_wipe_dist = 0
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe-plus_0.2mm.inst.cfg

@@ -15,7 +15,6 @@ weight = -2
 infill_overlap = 0
 infill_wipe_dist = 0
 machine_min_cool_heat_time_window = 15
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe_0.06mm.inst.cfg

@@ -15,7 +15,6 @@ weight = 1
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature - 5
 retraction_prime_speed = =retraction_speed
 speed_infill = =math.ceil(speed_print * 40 / 50)

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe_0.15mm.inst.cfg

@@ -13,7 +13,6 @@ weight = -1
 
 [values]
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 retraction_prime_speed = =retraction_speed
 speed_infill = =math.ceil(speed_print * 50 / 60)

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe_0.1mm.inst.cfg

@@ -15,7 +15,6 @@ weight = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 retraction_prime_speed = =retraction_speed
 speed_infill = =math.ceil(speed_print * 45 / 55)
 speed_print = 55

resources/quality/ultimaker_s3/um_s3_aa0.4_cpe_0.2mm.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 retraction_prime_speed = =retraction_speed
 skin_overlap = 20

resources/quality/ultimaker_s3/um_s3_aa0.4_nylon_0.06mm.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = 1
 
 [values]
-material_initial_print_temperature = =material_print_temperature - 5
 ooze_shield_angle = 40
 raft_airgap = 0.4
 retraction_prime_speed = =retraction_speed

resources/quality/ultimaker_s3/um_s3_aa0.4_nylon_0.15mm.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = -1
 
 [values]
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 5
 ooze_shield_angle = 40
 raft_airgap = 0.4

resources/quality/ultimaker_s3/um_s3_aa0.4_nylon_0.1mm.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = 0
 
 [values]
-material_initial_print_temperature = =material_print_temperature - 5
 ooze_shield_angle = 40
 raft_airgap = 0.4
 retraction_prime_speed = =retraction_speed

resources/quality/ultimaker_s3/um_s3_aa0.4_nylon_0.2mm.inst.cfg

@@ -12,7 +12,6 @@ variant = AA 0.4
 weight = -2
 
 [values]
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 ooze_shield_angle = 40
 raft_airgap = 0.4

resources/quality/ultimaker_s3/um_s3_aa0.4_pc_0.06mm.inst.cfg

@@ -20,7 +20,6 @@ infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature - 10
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40

resources/quality/ultimaker_s3/um_s3_aa0.4_pc_0.15mm.inst.cfg

@@ -19,7 +19,6 @@ infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40

resources/quality/ultimaker_s3/um_s3_aa0.4_pc_0.1mm.inst.cfg

@@ -19,7 +19,6 @@ infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.4_pc_0.2mm.inst.cfg

@@ -20,7 +20,6 @@ infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature + 10
 multiple_mesh_overlap = 0
 ooze_shield_angle = 40

resources/quality/ultimaker_s3/um_s3_aa0.4_petg_0.06mm.inst.cfg

@@ -15,7 +15,6 @@ weight = 1
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 10
 speed_infill = =math.ceil(speed_print * 40 / 50)
 speed_print = 50

resources/quality/ultimaker_s3/um_s3_aa0.4_petg_0.15mm.inst.cfg

@@ -13,7 +13,6 @@ weight = -1
 
 [values]
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
-material_initial_print_temperature = =material_print_temperature - 5
 material_print_temperature = =default_material_print_temperature
 speed_infill = =math.ceil(speed_print * 50 / 60)
 speed_print = 60

resources/quality/ultimaker_s3/um_s3_aa0.4_petg_0.1mm.inst.cfg

@@ -15,7 +15,6 @@ weight = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 5
 speed_infill = =math.ceil(speed_print * 45 / 55)
 speed_print = 55

resources/quality/ultimaker_s3/um_s3_aa0.4_petg_0.2mm.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
-material_initial_print_temperature = =material_print_temperature
 material_print_temperature = =default_material_print_temperature + 5
 skin_overlap = 20
 speed_infill = =math.ceil(speed_print * 50 / 60)

resources/quality/ultimaker_s3/um_s3_aa0.4_pp_0.15mm.inst.cfg

@@ -13,15 +13,14 @@ weight = -1
 
 [values]
 brim_width = 20
-cool_min_temperature = =material_print_temperature - 10
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
-material_final_print_temperature = =material_print_temperature - 12
+material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 2
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 13
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker_s3/um_s3_aa0.4_pp_0.1mm.inst.cfg

@@ -13,7 +13,6 @@ weight = 0
 
 [values]
 brim_width = 20
-cool_min_temperature = =material_print_temperature - 10
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
@@ -21,7 +20,7 @@ machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 5
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 15
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker_s3/um_s3_aa0.4_pp_0.2mm.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 brim_width = 20
-cool_min_temperature = =material_print_temperature - 10
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
@@ -21,7 +20,7 @@ machine_min_cool_heat_time_window = 15
 machine_nozzle_cool_down_speed = 0.85
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 5
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 5
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker_s3/um_s3_aa0.4_tpu_0.15mm.inst.cfg

@@ -13,7 +13,6 @@ weight = -1
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =5 * layer_height
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
@@ -24,7 +23,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0
 prime_tower_wipe_enabled = True

resources/quality/ultimaker_s3/um_s3_aa0.4_tpu_0.1mm.inst.cfg

@@ -13,7 +13,6 @@ weight = 0
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =5 * layer_height
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
@@ -24,7 +23,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 multiple_mesh_overlap = 0
 prime_tower_wipe_enabled = True
 retraction_count_max = 15

resources/quality/ultimaker_s3/um_s3_aa0.4_tpu_0.2mm.inst.cfg

@@ -13,7 +13,6 @@ weight = -2
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 gradual_infill_step_height = =5 * layer_height
 infill_overlap = 0
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
@@ -24,7 +23,7 @@ machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 106
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0
 prime_tower_wipe_enabled = True

resources/quality/ultimaker_s3/um_s3_aa0.8_pla_0.2mm.inst.cfg

@@ -15,7 +15,6 @@ weight = -2
 gradual_infill_step_height = =3 * layer_height
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker_s3/um_s3_aa0.8_pla_0.3mm.inst.cfg

@@ -15,7 +15,6 @@ weight = -3
 gradual_infill_step_height = =3 * layer_height
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker_s3/um_s3_aa0.8_pla_0.4mm.inst.cfg

@@ -15,7 +15,6 @@ weight = -4
 gradual_infill_step_height = =3 * layer_height
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 15
 prime_tower_enable = True
 speed_infill = =math.ceil(speed_print * 35 / 45)

resources/quality/ultimaker_s3/um_s3_aa0.8_pp_0.2mm.inst.cfg

@@ -13,8 +13,9 @@ weight = -2
 
 [values]
 brim_width = 25
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
+material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 2
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.8_pp_0.3mm.inst.cfg

@@ -13,8 +13,9 @@ weight = -3
 
 [values]
 brim_width = 25
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
+material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 10
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True
 prime_tower_flow = 100

resources/quality/ultimaker_s3/um_s3_aa0.8_pp_0.4mm.inst.cfg

@@ -13,8 +13,9 @@ weight = -4
 
 [values]
 brim_width = 25
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
+material_final_print_temperature = =material_print_temperature - 10
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.8_tough-pla_0.2mm.inst.cfg

@@ -16,7 +16,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cubic'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 0
 prime_tower_enable = False
 speed_print = 45

resources/quality/ultimaker_s3/um_s3_aa0.8_tough-pla_0.3mm.inst.cfg

@@ -16,7 +16,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cubic'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 5
 prime_tower_enable = False
 speed_infill = =math.ceil(speed_print * 30 / 35)

resources/quality/ultimaker_s3/um_s3_aa0.8_tough-pla_0.4mm.inst.cfg

@@ -16,7 +16,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cubic'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 5
 prime_tower_enable = False
 speed_infill = =math.ceil(speed_print * 30 / 30)

resources/quality/ultimaker_s3/um_s3_aa0.8_tpu_0.2mm.inst.cfg

@@ -13,13 +13,12 @@ weight = -2
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
 machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 105
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 2
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_aa0.8_tpu_0.3mm.inst.cfg

@@ -13,14 +13,13 @@ weight = -3
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
 infill_sparse_density = 15
 machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 105
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True
 prime_tower_flow = 100

resources/quality/ultimaker_s3/um_s3_aa0.8_tpu_0.4mm.inst.cfg

@@ -13,14 +13,13 @@ weight = -4
 
 [values]
 brim_width = 8.75
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'cross_3d'
 infill_sparse_density = 15
 machine_nozzle_cool_down_speed = 0.5
 machine_nozzle_heat_up_speed = 2.5
 material_final_print_temperature = =material_print_temperature - 10
 material_flow = 105
-material_initial_print_temperature = =material_print_temperature
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 2
 multiple_mesh_overlap = 0.2
 prime_tower_enable = True

resources/quality/ultimaker_s3/um_s3_cc0.4_pla_0.15mm.inst.cfg

@@ -17,7 +17,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker_s3/um_s3_cc0.4_pla_0.2mm.inst.cfg

@@ -17,7 +17,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker_s3/um_s3_cc0.6_pla_0.15mm.inst.cfg

@@ -17,7 +17,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker_s3/um_s3_cc0.6_pla_0.2mm.inst.cfg

@@ -17,7 +17,6 @@ gradual_infill_step_height = =3 * layer_height
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'triangles'
 machine_nozzle_cool_down_speed = 0.75
 machine_nozzle_heat_up_speed = 1.6
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature + 10
 prime_tower_enable = True
 speed_print = 45

resources/quality/ultimaker_s5/um_s5_aa0.25_pla_0.1mm.inst.cfg

@@ -17,7 +17,6 @@ infill_overlap = =0 if infill_sparse_density > 80 else 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'grid'
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_heat_up_speed = 1.4
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = 190
 retraction_hop = 0.2
 skin_overlap = 5

resources/quality/ultimaker_s5/um_s5_aa0.25_pp_0.1mm.inst.cfg

@@ -14,12 +14,11 @@ weight = 0
 
 [values]
 brim_width = 10
-cool_min_temperature = =material_print_temperature - 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'tetrahedral'
 infill_wipe_dist = 0.1
 machine_min_cool_heat_time_window = 15
 material_final_print_temperature = =material_print_temperature - 10
-material_initial_print_temperature = =material_print_temperature - 5
+material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 15
 multiple_mesh_overlap = 0
 prime_tower_enable = False

resources/quality/ultimaker_s5/um_s5_aa0.25_tough-pla_0.1mm.inst.cfg

@@ -17,7 +17,6 @@ infill_overlap = =0 if infill_sparse_density > 80 else 10
 infill_pattern = ='zigzag' if infill_sparse_density > 80 else 'grid'
 machine_nozzle_cool_down_speed = 0.9
 machine_nozzle_heat_up_speed = 1.4
-material_initial_print_temperature = =material_print_temperature - 10
 material_print_temperature = =default_material_print_temperature - 15
 skin_overlap = 5
 speed_print = 30

resources/quality/ultimaker_s5/um_s5_aa0.4_abs_0.06mm.inst.cfg

@@ -15,7 +15,6 @@ weight = 1
 machine_nozzle_cool_down_speed = 0.8
 machine_nozzle_heat_up_speed = 1.5
 material_final_print_temperature = =material_print_temperature - 20
-material_initial_print_temperature = =material_print_temperature - 15
 material_print_temperature = =default_material_print_temperature + 5
 prime_tower_enable = False
 raft_airgap = 0.15