Update README.md

README.md

@@ -4,20 +4,19 @@
 FW for ESP8266 used with 3D printer
 
 ##Description      
-Thanks to @disneysw for bringing this module idea and basic code    
+Thanks to @disneysw for bringing this module idea
 Thanks to @lkarlslund for suggestion about independant reset using GPIO2   
 
-Have a bridge configurable by web and optionally by printer   
-Have a front end to know what is the wifi status or know what is the print status  - this part can be optional and removed by compilation directive if no need    
-...     
-TBD     
+Have a bridge configurable by web (implemented) and optionally by printer (not yet implemented)  
+Have a front end to know what is the wifi status (implemented) or know what is the print status (not yet implemented) - this part can be optional and removed by compilation directive if no need    
+    
 
 ##Hardware connection       
 --Use GPIO2 to ground to reset all settings in hard way - 2-6 sec after boot / not before!! Set GPIO2 to ground before boot change boot mode and go to special boot that do not reach FW - I did not found information on this. Currently boot take 10 sec - giving 8 seconds to connect GPIO2 to GND and do an hard recovery for settings   
 --Use GPIO0 to ground to be in update mode   
 --Use a switch to reset/disable module    
 --TODO: Full wiring with drawing     
-TBD         
+       
 
 ##Development   
 Currently using [Arduino IDE 1.6.4](http://arduino.cc/en/Main/Software)  with the esp8266 module from board manager added from [github.com/esp8266/Arduino](https://github.com/esp8266/Arduino)
@@ -27,21 +26,20 @@ Additionnaly:
 
 ##Flash the Module    
 *Tools:      
---Use IDE to upload directly    
---Use esp flasher: https://github.com/nodemcu/nodemcu-flasher  for 0x00000 and 0X00004 binaries   
+--Use IDE to upload directly  (latest version of board manager module generate one binary)    
 
 *Connection
---Connect GPIO0 to ground to be in update mode 
+--Connect GPIO0 to ground to be in update mode
 
-##Wifi connection      
+##Web configuration      
 *Wifi Mode : Access point / Client station  
 *IP Generation: DHCP/Static IP      
 *IP/MASK/GATEWAY for static data    
 *Baud Rate for serial (supported : 9600, 19200, 38400, 57600, 115200, 230400)    
-...       
-TBD   
+*web port and data port      
+
     
-##Configuration      
+##Default Configuration      
 Default Settings:    
 AP:ESP8266    
 PW:12345678   
@@ -54,58 +52,46 @@ IP Mode: Static IP
 IP: 192.168.0.1   
 Mask: 255.255.255.0   
 GW:192.168.0.1    
-Baud rate: 9600 
+Baud rate: 9600   
+Web port:80   
+Data port: 8888   
 
-From web: 
-port 80
---Need picture and flow    
+These are the UI when css is in cache or internet is available:    
 <img src=https://raw.githubusercontent.com/luc-github/ESP8266/master/Page1.png><br> 
 <img src=https://raw.githubusercontent.com/luc-github/ESP8266/master/Page2.png><br>     
 <img src=https://raw.githubusercontent.com/luc-github/ESP8266/master/Page3.png><br>     
 <img src=https://raw.githubusercontent.com/luc-github/ESP8266/master/Page4.png>     
 
 
-...    
-TBD
-
-
 ##Commands from/to serial(not yet implemented):    
 *from module to printer   [Need Printer FW support and can be disabled in ESP FW]    
     -M800 S1 , restart module done need a wifi/activity restart      
     -M801 [Message], Error message from module      
     -M802 [Message], Status message from module        
     -M804 [AP/STATION,SSID,DHC/STATIC,IP,MASK,GW,STATUS,MAC ADDRESSS, BAUD?], ]Module configuration without password    
-    ...    
-    TBD    
         
 *from host to printer   (not yet implemented) [Need Printer FW support] on port 8888    
     -M803 [IP, AP,SSID, Password....], ]Module configuration settings to be used  by module    
     -M805 query to get M804 informations    
-    ...      
-    TBD           
+          
 
 
 *from printer to module   [Need Printer FW support and can be disabled in ESP FW] (not yet implemented)  
     -request configuration/status (generate the M804 as answer)   
     -set AP/STATION,SSID,PASSSWORD,DHC/STATIC,IP,MASK,GW,BAUD from serial    
-    ...    
-    TBD    
  
-##Front End [need Printer FW support it] or just display module status
+##Front End (not yet implemented)  [need Printer FW support it] or just display module status 
 --Display printer status   
 --Display temperatures   
 --Display print progress if any   
 --List SDCard Content   
---Launch/Stop/(Pause?) a Print
+--Launch/Stop/(Pause?) a Print   
  
 ##TODO    
 -- Define Front End Functions  
--- do the bridge serial/TCPIP
--- do coding   
 -- do testing   
 -- do a complete drawing for connections    
--- add some Javascript to enhance web UI 
--- allow to change ports from Web UI, currently fixed to 80 and 8888
+-- add some Javascript to enhance web UI     
 
 
 more to come