* Change STA SSID [ESP100] if authentication is on, need admin password [ESP100]pwd= * Change STA Password [ESP101] if authentication is on, need admin password [ESP101]pwd= * Change Hostname [ESP102] if authentication is on, need admin password [ESP102]pwd= * Change Wifi mode (STA/AP) [ESP103] if authentication is on, need admin password [ESP103]pwd= * Change STA IP mode (DHCP/STATIC) [ESP104] if authentication is on, need admin password [ESP104]pwd= * Change AP SSID [ESP105] if authentication is on, need admin password [ESP105]pwd= * Change AP Password [ESP106] if authentication is on, need admin password [ESP106]pwd= * Change AP IP mode (DHCP/STATIC) [ESP107] if authentication is on, need admin password [ESP107]pwd= * Set wifi on/off [ESP110] state can be ON, OFF, RESTART if authentication is on, need admin password [ESP110]pwd= * Get current IP [ESP111]

* Get hostname [ESP112]

*Get/Set pin value [ESP201]P V [PULLUP=YES RAW=YES ANALOG=NO ANALOG_RANGE=255 CLEARCHANNELS=NO]pwd= if no V get P value if V 0/1 set INPUT_PULLUP value, but for GPIO16 INPUT_PULLDOWN_16 GPIO1 and GPIO3 cannot be used as they are used for serial if PULLUP=YES set input pull up, if not set input if RAW=YES do not set pinmode just read value * Output to oled column C and line L [ESP210]C= L= T= * Output to oled line 1 [ESP211] * Output to oled line 2 [ESP212] * Output to oled line 3 [ESP213] * Output to oled line 4 [ESP214] * Delay command [ESP290][pwd=] * Give EEPROM Version detected [ESP300] *Get full EEPROM settings content but do not give any passwords can filter if only need wifi or printer [ESP400] *Set EEPROM setting position in EEPROM, type: B(byte), I(integer/long), S(string), A(IP address / mask) [ESP401]P= T= V= pwd= Positions: * EP_WIFI_MODE 0 //1 byte = flag * EP_STA_SSID 1 //33 bytes 32+1 = string ; warning does not support multibyte char like chinese * EP_STA_PASSWORD 34 //65 bytes 64 +1 = string ;warning does not support multibyte char like chinese * EP_STA_IP_MODE 99 //1 byte = flag * EP_STA_IP_VALUE 100 //4 bytes xxx.xxx.xxx.xxx * EP_STA_MASK_VALUE 104 //4 bytes xxx.xxx.xxx.xxx * EP_STA_GATEWAY_VALUE 108 //4 bytes xxx.xxx.xxx.xxx * EP_BAUD_RATE 112 //4 bytes = int * EP_STA_PHY_MODE 116 //1 byte = flag * EP_SLEEP_MODE 117 //1 byte = flag * EP_CHANNEL 118 //1 byte = flag * EP_AUTH_TYPE 119 //1 byte = flag * EP_SSID_VISIBLE 120 //1 byte = flag * EP_WEB_PORT 121 //4 bytes = int * EP_DATA_PORT 125 //4 bytes = int * EP_OUTPUT_FLAG 129 //1 bytes = flag * EP_HOSTNAME 130//33 bytes 32+1 = string ; warning does not support multibyte char like chinese * EP_DHT_INTERVAL 164//4 bytes = int * EP_FREE_INT2 168//4 bytes = int * EP_FREE_INT3 172//4 bytes = int * EP_ADMIN_PWD 176//21 bytes 20+1 = string ; warning does not support multibyte char like chinese * EP_USER_PWD 197//21 bytes 20+1 = string ; warning does not support multibyte char like chinese * EP_AP_SSID 218 //33 bytes 32+1 = string ; warning does not support multibyte char like chinese * EP_AP_PASSWORD 251 //65 bytes 64 +1 = string ;warning does not support multibyte char like chinese * EP_AP_IP_VALUE 316 //4 bytes xxx.xxx.xxx.xxx * EP_AP_MASK_VALUE 320 //4 bytes xxx.xxx.xxx.xxx * EP_AP_GATEWAY_VALUE 324 //4 bytes xxx.xxx.xxx.xxx * EP_AP_IP_MODE 329 //1 byte = flag * EP_AP_PHY_MODE 330 //1 byte = flag * EP_FREE_STRING1 331 //129 bytes 128+1 = string ; warning does not support multibyte char like chinese * EP_DHT_TYPE 460 //1 bytes = flag * EP_TARGET_FW 461 //1 bytes = flag *Get available AP list (limited to 30) output is JSON or plain text according parameter [ESP410] *Get current settings of ESP3D output is JSON or plain text according parameter [ESP420] * Get/Set ESP mode cmd can be RESET, SAFEMODE, CONFIG, RESTART [ESP444] if authentication is on, need admin password for RESET, RESTART and SAFEMODE [ESP444]pwd= * Send GCode with check sum caching right line numbering [ESP500] * Send line checksum [ESP501] * Change / Reset user password [ESP555]pwd= if no password set it use default one * Send Notification [ESP600]msg [pwd=] * Set/Get Notification settings [ESP610]type= T1= T2= TS= [pwd=] Get will give type and settings only not the protected T1/T2 * Read SPIFFS file and send each line to serial [ESP700] * Format SPIFFS [ESP710]FORMAT pwd= * SPIFFS total size and used size [ESP720]

* Get fw version and basic information [ESP800]

* Get fw target [ESP801]

* Get state / Set Enable / Disable Serial Communication [ESP900]