Note: 1 - add space to separate parameters 2 - if parameter has space add \ in front of space to not be seen as separator * Set/Get STA SSID [ESP100]pwd= * Set STA Password [ESP101]pwd= * Set/Get STA IP mode (DHCP/STATIC) [ESP102]pwd= * Set/Get STA IP/Mask/GW [ESP103]IP= MSK= GW= pwd= * Set/Get AP SSID [ESP105]pwd= * Change AP Password [ESP106]pwd= * Set/Get AP IP [ESP107]pwd= * Set/Get AP channel [ESP108]pwd= * Set/Get radio state which can be WIFI-STA, WIFI-AP, BT, ETH-STA, ETH-AP, OFF [ESP110]pwd= * Get current IP [ESP111]

* Get/Set hostname [ESP112] pwd= * Get/Set immediate network(WiFi/BT/Ethernet) state which can be ON, OFF [ESP115]pwd= * Get/Set HTTP state which can be ON, OFF [ESP120]pwd= * Get/Set HTTP port [ESP121]pwd= * Get/Set Telnet state which can be ON, OFF [ESP130]pwd= * Get/Set Telnet port [ESP131]pwd= * Init / Get current time [ESP140]

pwd= *Get/Set pin value [ESP201]P V [PULLUP=YES RAW=YES]pwd= if no V get P value if V 0/1 set INPUT_PULLUP value, but for GPIO16(ESP8266) INPUT_PULLDOWN_16 if PULLUP=YES set input pull up (for GPIO16(ESP8266) INPUT_PULLDOWN_16), if not set input if RAW=YES do not set pinmode just read value Flash pins (6~11) cannot be used * Get full EEPROM settings content but do not give any passwords [ESP400] pwd= *Set EEPROM setting position in EEPROM, type: B(byte), I(integer/long), S(string), A(IP address / mask) [ESP401]P= T= V= pwd= Description: Positions: ESP_RADIO_MODE 0 //1 byte = flag ESP_STA_SSID 1 //33 bytes 32+1 = string ; warning does not support multibyte char like chinese ESP_STA_PASSWORD 34 //65 bytes 64 +1 = string ;warning does not support multibyte char like chinese ESP_STA_IP_MODE 99 //1 byte = flag ESP_STA_IP_VALUE 100 //4 bytes xxx.xxx.xxx.xxx ESP_STA_MASK_VALUE 104 //4 bytes xxx.xxx.xxx.xxx ESP_STA_GATEWAY_VALUE 108 //4 bytes xxx.xxx.xxx.xxx ESP_BAUD_RATE 112 //4 bytes = int ESP_STA_PHY_MODE 116 //1 byte = flag ESP_SLEEP_MODE 117 //1 byte = flag ESP_AP_CHANNEL 118 //1 byte = flag ESP_AP_AUTH_TYPE 119 //1 byte = flag ESP_SSID_VISIBLE 120 //1 byte = flag ESP_HTTP_PORT 121 //4 bytes = int ESP_TELNET_PORT 125 //4 bytes = int ESP_OUTPUT_FLAG 129 //1 bytes = flag ESP_HOSTNAME 130 //33 bytes 32+1 = string ; warning does not support multibyte char like chinese ESP_DHT_INTERVAL 164 //4 bytes = int ESP_SETTINGS_VERSION 168 //8 bytes = 7+1 = string ESP3D + 2 digits ESP_ADMIN_PWD 176 //21 bytes 20+1 = string ; warning does not support multibyte char like chinese ESP_USER_PWD 197 //21 bytes 20+1 = string ; warning does not support multibyte char like chinese ESP_AP_SSID 218 //33 bytes 32+1 = string ; warning does not support multibyte char like chinese ESP_AP_PASSWORD 251 //65 bytes 64 +1 = string ;warning does not support multibyte char like chinese ESP_AP_IP_VALUE 316 //4 bytes xxx.xxx.xxx.xxx ESP_HTTP_ON 328 //1 byte = flag ESP_TELNET_ON 329 //1 byte = flag ESP_AP_PHY_MODE 330 //1 byte = flag ESP_SD_SPEED_DIV 331 //1 byte = flag ESP_DHT_TYPE 460//1 bytes = flag ESP_TARGET_FW 461 //1 bytes = flag ESP_TIMEZONE 462//1 bytes = flag ESP_TIME_IS_DST 463//1 bytes = flag ESP_TIME_SERVER1 464//129 bytes 128+1 = string ; warning does not support multibyte char like chinese ESP_TIME_SERVER2 593 //129 bytes 128+1 = string ; warning does not support multibyte char like chinese ESP_TIME_SERVER3 722 //129 bytes 128+1 = string ; warning does not support multibyte char like chinese ESP_IS_DIRECT_SD 850//1 bytes = flag ESP_PRIMARY_SD 851//1 bytes = flag ESP_SECONDARY_SD 852//1 bytes = flag ESP_DIRECT_SD_CHECK 853//1 bytes = flag ESP_SD_CHECK_UPDATE_AT_BOOT 854//1 bytes = flag *Get available AP list (limited to 30) output is JSON or plain text according parameter [ESP410] *Get current settings of ESP3D output is plain text [ESP420] * Set ESP State cmd are RESTART / RESET [ESP444] * Change admin password [ESP550]pwd= * Change user password [ESP555]pwd= * Format ESP Filesystem [ESP710]FORMAT pwd= * List ESP Filesystem [ESP720] pwd= * FW Informations [ESP800] pwd=