mirror of
https://git.mirrors.martin98.com/https://github.com/luc-github/ESP3D.git
synced 2025-08-05 14:30:42 +08:00
93312ff8b5
* Update WebSocket library * Update SSDP library * Update TFT_eSPI library * Update EspLuaEngine library * Update SDFat library * Change to pioarduino * Make ESP3DMessageFIFO and ESP3DMessage more thread safe * Fix sanity checks for BT * Add some C6 support * Refactor ethernet code * Split Ethernet Sta / WiFi sta ESP Commands and settings * Simplify wait and wdtFeed code * Set C3 with 4MB by default in platformio.ini * Apply Disable brown out only on ESP32 to avoid crash e.g:ESP32S3 * Add missing entries in platformio.ini
57 lines
2.4 KiB
C
57 lines
2.4 KiB
C
// See SetupX_Template.h for all options available
|
|
#define USER_SETUP_ID 9
|
|
|
|
#define ST7735_DRIVER
|
|
|
|
|
|
#define TFT_WIDTH 128
|
|
#define TFT_HEIGHT 160
|
|
|
|
|
|
#define ST7735_REDTAB
|
|
|
|
// For ST7735, ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
|
|
// Try ONE option at a time to find the correct colour order for your display
|
|
|
|
// #define TFT_RGB_ORDER TFT_RGB // Colour order Red-Green-Blue
|
|
// #define TFT_RGB_ORDER TFT_BGR // Colour order Blue-Green-Red
|
|
|
|
// Overlap mode shares the ESP8266 FLASH SPI bus with the TFT so has a performance impact
|
|
// but saves pins for other functions. It is best not to connect MISO as some displays
|
|
// do not tristate that line when chip select is high!
|
|
// Note: Only one SPI device can share the FLASH SPI lines, so a SPI touch controller
|
|
// cannot be connected as well to the same SPI signals.
|
|
// On NodeMCU 1.0 SD0=MISO, SD1=MOSI, CLK=SCLK to connect to TFT in overlap mode
|
|
// On NodeMCU V3 S0 =MISO, S1 =MOSI, S2 =SCLK
|
|
// In ESP8266 overlap mode the following must be defined
|
|
#define TFT_SPI_OVERLAP
|
|
|
|
// In ESP8266 overlap mode the TFT chip select MUST connect to pin D3
|
|
#define TFT_CS PIN_D3
|
|
#define TFT_DC PIN_D5 // Data Command control pin
|
|
#define TFT_RST PIN_D4 // Reset pin (could connect to NodeMCU RST, see next line)
|
|
//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to NodeMCU RST or 3.3V
|
|
|
|
|
|
|
|
|
|
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
|
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
|
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
|
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
|
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:.
|
|
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
|
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
|
|
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
|
|
|
#define SMOOTH_FONT
|
|
|
|
|
|
// #define SPI_FREQUENCY 20000000
|
|
#define SPI_FREQUENCY 27000000
|
|
|
|
#define SPI_TOUCH_FREQUENCY 2500000
|
|
|
|
|
|
// #define SUPPORT_TRANSACTIONS
|