#
msgid ""
msgstr ""
"Project-Id-Version: Orca Slicer\n"
"Report-Msgid-Bugs-To: \n"
"POT-Creation-Date: 2025-03-16 22:32+0800\n"
"PO-Revision-Date: 2025-05-18 09:32-0300\n"
"Last-Translator: Alexandre Folle de Menezes\n"
"Language-Team: \n"
"Language: en\n"
"MIME-Version: 1.0\n"
"Content-Type: text/plain; charset=UTF-8\n"
"Content-Transfer-Encoding: 8bit\n"
"Plural-Forms: nplurals=2; plural=(n==1) ? 0 : 1;\n"
"X-Generator: Poedit 3.6\n"

msgid "Support Painting"
msgstr ""

msgid "Alt + Mouse wheel"
msgstr ""

msgid "Section view"
msgstr ""

msgid "Reset direction"
msgstr ""

msgid "Ctrl + Mouse wheel"
msgstr ""

msgid "Pen size"
msgstr ""

msgid "Left mouse button"
msgstr ""

msgid "Enforce supports"
msgstr ""

msgid "Right mouse button"
msgstr ""

msgid "Block supports"
msgstr ""

msgid "Shift + Left mouse button"
msgstr ""

msgid "Erase"
msgstr ""

msgid "Erase all painting"
msgstr ""

msgid "Highlight overhang areas"
msgstr "Highlight overhangs"

msgid "Gap fill"
msgstr ""

msgid "Perform"
msgstr "Apply"

msgid "Gap area"
msgstr ""

msgid "Tool type"
msgstr ""

msgid "Smart fill angle"
msgstr ""

msgid "On overhangs only"
msgstr ""

msgid "Auto support threshold angle: "
msgstr ""

msgid "Circle"
msgstr ""

msgid "Sphere"
msgstr ""

msgid "Fill"
msgstr ""

msgid "Gap Fill"
msgstr ""

#, boost-format
msgid "Allows painting only on facets selected by: \"%1%\""
msgstr ""

msgid "Highlight faces according to overhang angle."
msgstr ""

msgid "No auto support"
msgstr ""

msgid "Support Generated"
msgstr "Support generated"

msgid "Gizmo-Place on Face"
msgstr ""

msgid "Lay on face"
msgstr "Lay on Face"

#, boost-format
msgid ""
"Filament count exceeds the maximum number that painting tool supports. Only "
"the first %1% filaments will be available in painting tool."
msgstr ""

msgid "Color Painting"
msgstr "Color painting"

msgid "Pen shape"
msgstr ""

msgid "Paint"
msgstr ""

msgid "Key 1~9"
msgstr ""

msgid "Choose filament"
msgstr ""

msgid "Edge detection"
msgstr ""

msgid "Triangles"
msgstr ""

msgid "Filaments"
msgstr ""

msgid "Brush"
msgstr ""

msgid "Smart fill"
msgstr ""

msgid "Bucket fill"
msgstr ""

msgid "Height range"
msgstr ""

msgid "Alt + Shift + Enter"
msgstr ""

msgid "Toggle Wireframe"
msgstr ""

msgid "Shortcut Key "
msgstr ""

msgid "Triangle"
msgstr ""

msgid "Height Range"
msgstr ""

msgid "Vertical"
msgstr ""

msgid "Horizontal"
msgstr ""

msgid "Remove painted color"
msgstr ""

#, boost-format
msgid "Painted using: Filament %1%"
msgstr ""

msgid "Move"
msgstr ""

msgid "Gizmo-Move"
msgstr ""

msgid "Rotate"
msgstr ""

msgid "Gizmo-Rotate"
msgstr ""

msgid "Optimize orientation"
msgstr ""

msgid "Apply"
msgstr ""

msgid "Scale"
msgstr ""

msgid "Gizmo-Scale"
msgstr ""

msgid "Error: Please close all toolbar menus first"
msgstr ""

msgid "in"
msgstr ""

msgid "mm"
msgstr ""

msgid "Position"
msgstr ""

#. TRN - Input label. Be short as possible
#. Angle between Y axis and text line direction.
#. TRN - Input label. Be short as possible
msgid "Rotation"
msgstr ""

msgid "Scale ratios"
msgstr ""

msgid "Object Operations"
msgstr "Object operations"

msgid "Volume Operations"
msgstr "Volume operations"

msgid "Translate"
msgstr ""

msgid "Group Operations"
msgstr "Group operations"

msgid "Set Position"
msgstr "Set position"

msgid "Set Orientation"
msgstr "Set orientation"

msgid "Set Scale"
msgstr "Set scale"

msgid "Reset Position"
msgstr "Reset position"

msgid "Reset Rotation"
msgstr "Reset rotation"

msgid "World coordinates"
msgstr ""

msgid "Object coordinates"
msgstr ""

msgid "°"
msgstr ""

#. TRN - Input label. Be short as possible
msgid "Size"
msgstr ""

msgid "%"
msgstr ""

msgid "uniform scale"
msgstr "Uniform scale"

msgid "Planar"
msgstr ""

msgid "Dovetail"
msgstr ""

msgid "Auto"
msgstr ""

msgid "Manual"
msgstr ""

msgid "Plug"
msgstr ""

msgid "Dowel"
msgstr ""

msgid "Snap"
msgstr ""

msgid "Prism"
msgstr ""

msgid "Frustum"
msgstr ""

msgid "Square"
msgstr ""

msgid "Hexagon"
msgstr ""

msgid "Keep orientation"
msgstr ""

msgid "Place on cut"
msgstr ""

msgid "Flip upside down"
msgstr ""

msgid "Connectors"
msgstr ""

msgid "Type"
msgstr ""

msgid "Style"
msgstr ""

msgid "Shape"
msgstr ""

#. TRN - Input label. Be short as possible
#. Size in emboss direction
#. TRN - Input label. Be short as possible
msgid "Depth"
msgstr ""

msgid "Groove"
msgstr ""

msgid "Width"
msgstr ""

msgid "Flap Angle"
msgstr ""

msgid "Groove Angle"
msgstr ""

msgid "Part"
msgstr ""

msgid "Object"
msgstr ""

msgid ""
"Click to flip the cut plane\n"
"Drag to move the cut plane"
msgstr ""

msgid ""
"Click to flip the cut plane\n"
"Drag to move the cut plane\n"
"Right-click a part to assign it to the other side"
msgstr ""

msgid "Move cut plane"
msgstr ""

msgid "Mode"
msgstr ""

msgid "Change cut mode"
msgstr ""

msgid "Tolerance"
msgstr ""

msgid "Drag"
msgstr ""

msgid "Draw cut line"
msgstr ""

msgid "Left click"
msgstr ""

msgid "Add connector"
msgstr ""

msgid "Right click"
msgstr ""

msgid "Remove connector"
msgstr ""

msgid "Move connector"
msgstr ""

msgid "Add connector to selection"
msgstr ""

msgid "Remove connector from selection"
msgstr ""

msgid "Select all connectors"
msgstr ""

msgid "Cut"
msgstr ""

msgid "Rotate cut plane"
msgstr ""

msgid "Remove connectors"
msgstr ""

msgid "Bulge"
msgstr ""

msgid "Bulge proportion related to radius"
msgstr ""

msgid "Space"
msgstr ""

msgid "Space proportion related to radius"
msgstr ""

msgid "Confirm connectors"
msgstr ""

msgid "Cancel"
msgstr ""

msgid "Build Volume"
msgstr ""

msgid "Flip cut plane"
msgstr ""

msgid "Groove change"
msgstr ""

msgid "Reset"
msgstr ""

#. TRN: This is an entry in the Undo/Redo stack. The whole line will be 'Edited: (name of whatever was edited)'.
msgid "Edited"
msgstr ""

msgid "Cut position"
msgstr ""

msgid "Reset cutting plane"
msgstr ""

msgid "Edit connectors"
msgstr ""

msgid "Add connectors"
msgstr ""

msgid "Reset cut"
msgstr ""

msgid "Reset cutting plane and remove connectors"
msgstr ""

msgid "Upper part"
msgstr ""

msgid "Lower part"
msgstr ""

msgid "Keep"
msgstr ""

msgid "Flip"
msgstr ""

msgid "After cut"
msgstr ""

msgid "Cut to parts"
msgstr ""

msgid "Perform cut"
msgstr ""

msgid "Warning"
msgstr ""

msgid "Invalid connectors detected"
msgstr ""

#, c-format, boost-format
msgid "%1$d connector is out of cut contour"
msgid_plural "%1$d connectors are out of cut contour"
msgstr[0] ""
msgstr[1] ""

#, c-format, boost-format
msgid "%1$d connector is out of object"
msgid_plural "%1$d connectors are out of object"
msgstr[0] ""
msgstr[1] ""

msgid "Some connectors are overlapped"
msgstr ""

msgid "Select at least one object to keep after cutting."
msgstr ""

msgid "Cut plane is placed out of object"
msgstr ""

msgid "Cut plane with groove is invalid"
msgstr ""

msgid "Connector"
msgstr ""

msgid "Cut by Plane"
msgstr ""

msgid "non-manifold edges be caused by cut tool, do you want to fix it now?"
msgstr "Non-manifold edges be caused by cut tool: do you want to fix now?"

msgid "Repairing model object"
msgstr ""

msgid "Cut by line"
msgstr ""

msgid "Delete connector"
msgstr ""

msgid "Mesh name"
msgstr ""

msgid "Detail level"
msgstr ""

msgid "Decimate ratio"
msgstr ""

#, boost-format
msgid ""
"Processing model '%1%' with more than 1M triangles could be slow. It is "
"highly recommended to simplify the model."
msgstr ""

msgid "Simplify model"
msgstr ""

msgid "Simplify"
msgstr ""

msgid "Simplification is currently only allowed when a single part is selected"
msgstr ""

msgid "Error"
msgstr ""

msgid "Extra high"
msgstr ""

msgid "High"
msgstr ""

msgid "Medium"
msgstr ""

msgid "Low"
msgstr ""

msgid "Extra low"
msgstr ""

#, c-format, boost-format
msgid "%d triangles"
msgstr ""

msgid "Show wireframe"
msgstr ""

#, boost-format
msgid "%1%"
msgstr ""

msgid "Can't apply when processing preview."
msgstr "Unable to apply when processing preview"

msgid "Operation already cancelling. Please wait a few seconds."
msgstr ""

msgid "Face recognition"
msgstr ""

msgid "Perform Recognition"
msgstr ""

msgid "Brush size"
msgstr ""

msgid "Brush shape"
msgstr ""

msgid "Enforce seam"
msgstr ""

msgid "Block seam"
msgstr ""

msgid "Seam painting"
msgstr ""

msgid "Remove selection"
msgstr ""

msgid "Entering Seam painting"
msgstr "Entering seam painting"

msgid "Leaving Seam painting"
msgstr "Leaving Seam Painting"

msgid "Paint-on seam editing"
msgstr ""

#. TRN - Input label. Be short as possible
#. Select look of letter shape
msgid "Font"
msgstr ""

msgid "Thickness"
msgstr ""

msgid "Text Gap"
msgstr ""

msgid "Angle"
msgstr ""

msgid ""
"Embedded\n"
"depth"
msgstr "Embedded depth"

msgid "Input text"
msgstr ""

msgid "Surface"
msgstr ""

msgid "Horizontal text"
msgstr ""

msgid "Shift + Mouse move up or down"
msgstr ""

msgid "Rotate text"
msgstr ""

msgid "Text shape"
msgstr ""

#. TRN - Title in Undo/Redo stack after rotate with text around emboss axe
msgid "Text rotate"
msgstr ""

#. TRN - Title in Undo/Redo stack after move with text along emboss axe - From surface
msgid "Text move"
msgstr ""

msgid "Set Mirror"
msgstr ""

msgid "Embossed text"
msgstr ""

msgid "Enter emboss gizmo"
msgstr ""

msgid "Leave emboss gizmo"
msgstr ""

msgid "Embossing actions"
msgstr ""

msgid "Emboss"
msgstr ""

msgid "NORMAL"
msgstr ""

msgid "SMALL"
msgstr ""

msgid "ITALIC"
msgstr ""

msgid "SWISS"
msgstr ""

msgid "MODERN"
msgstr ""

msgid "First font"
msgstr ""

msgid "Default font"
msgstr ""

msgid "Advanced"
msgstr ""

msgid ""
"The text cannot be written using the selected font. Please try choosing a "
"different font."
msgstr ""

msgid "Embossed text cannot contain only white spaces."
msgstr ""

msgid "Text contains character glyph (represented by '?') unknown by font."
msgstr ""

msgid "Text input doesn't show font skew."
msgstr ""

msgid "Text input doesn't show font boldness."
msgstr ""

msgid "Text input doesn't show gap between lines."
msgstr ""

msgid "Too tall, diminished font height inside text input."
msgstr ""

msgid "Too small, enlarged font height inside text input."
msgstr ""

msgid "Text doesn't show current horizontal alignment."
msgstr ""

msgid "Revert font changes."
msgstr ""

#, boost-format
msgid "Font \"%1%\" can't be selected."
msgstr ""

msgid "Operation"
msgstr ""

msgid "Join"
msgstr ""

msgid "Click to change text into object part."
msgstr ""

msgid "You can't change a type of the last solid part of the object."
msgstr ""

msgctxt "EmbossOperation"
msgid "Cut"
msgstr ""

msgid "Click to change part type into negative volume."
msgstr ""

msgid "Modifier"
msgstr ""

msgid "Click to change part type into modifier."
msgstr ""

msgid "Change Text Type"
msgstr ""

#, boost-format
msgid "Rename style (%1%) for embossing text"
msgstr ""

msgid "Name can't be empty."
msgstr ""

msgid "Name has to be unique."
msgstr ""

msgid "OK"
msgstr ""

msgid "Rename style"
msgstr ""

msgid "Rename current style."
msgstr ""

msgid "Can't rename temporary style."
msgstr ""

msgid "First Add style to list."
msgstr ""

#, boost-format
msgid "Save %1% style"
msgstr ""

msgid "No changes to save."
msgstr ""

msgid "New name of style"
msgstr ""

msgid "Save as new style"
msgstr ""

msgid "Only valid font can be added to style."
msgstr ""

msgid "Add style to my list."
msgstr ""

msgid "Save as new style."
msgstr ""

msgid "Remove style"
msgstr ""

msgid "Can't remove the last existing style."
msgstr ""

#, boost-format
msgid "Are you sure you want to permanently remove the \"%1%\" style?"
msgstr ""

#, boost-format
msgid "Delete \"%1%\" style."
msgstr ""

#, boost-format
msgid "Can't delete \"%1%\". It is last style."
msgstr ""

#, boost-format
msgid "Can't delete temporary style \"%1%\"."
msgstr ""

#, boost-format
msgid "Modified style \"%1%\""
msgstr ""

#, boost-format
msgid "Current style is \"%1%\""
msgstr ""

#, boost-format
msgid ""
"Changing style to \"%1%\" will discard current style modification.\n"
"\n"
"Would you like to continue anyway?"
msgstr ""

msgid "Not valid style."
msgstr ""

#, boost-format
msgid "Style \"%1%\" can't be used and will be removed from a list."
msgstr ""

msgid "Unset italic"
msgstr ""

msgid "Set italic"
msgstr ""

msgid "Unset bold"
msgstr ""

msgid "Set bold"
msgstr ""

msgid "Revert text size."
msgstr ""

msgid "Revert embossed depth."
msgstr ""

msgid ""
"Advanced options cannot be changed for the selected font.\n"
"Select another font."
msgstr ""

msgid "Revert using of model surface."
msgstr ""

msgid "Revert Transformation per glyph."
msgstr ""

msgid "Set global orientation for whole text."
msgstr ""

msgid "Set position and orientation per glyph."
msgstr ""

msgctxt "Alignment"
msgid "Left"
msgstr ""

msgctxt "Alignment"
msgid "Center"
msgstr ""

msgctxt "Alignment"
msgid "Right"
msgstr ""

msgctxt "Alignment"
msgid "Top"
msgstr ""

msgctxt "Alignment"
msgid "Middle"
msgstr ""

msgctxt "Alignment"
msgid "Bottom"
msgstr ""

msgid "Revert alignment."
msgstr ""

#. TRN EmbossGizmo: font units
msgid "points"
msgstr ""

msgid "Revert gap between characters"
msgstr ""

msgid "Distance between characters"
msgstr ""

msgid "Revert gap between lines"
msgstr ""

msgid "Distance between lines"
msgstr ""

msgid "Undo boldness"
msgstr ""

msgid "Tiny / Wide glyphs"
msgstr ""

msgid "Undo letter's skew"
msgstr ""

msgid "Italic strength ratio"
msgstr ""

msgid "Undo translation"
msgstr ""

msgid "Distance of the center of the text to the model surface."
msgstr ""

msgid "Undo rotation"
msgstr ""

msgid "Rotate text Clock-wise."
msgstr ""

msgid "Unlock the text's rotation when moving text along the object's surface."
msgstr ""

msgid "Lock the text's rotation when moving text along the object's surface."
msgstr ""

msgid "Select from True Type Collection."
msgstr ""

msgid "Set text to face camera"
msgstr ""

msgid "Orient the text towards the camera."
msgstr ""

#, boost-format
msgid "Font \"%1%\" can't be used. Please select another."
msgstr ""

#, boost-format
msgid ""
"Can't load exactly same font (\"%1%\"). Application selected a similar "
"one (\"%2%\"). You have to specify font for enable edit text."
msgstr ""

msgid "No symbol"
msgstr ""

msgid "Loading"
msgstr ""

msgid "In queue"
msgstr ""

#. TRN - Input label. Be short as possible
#. Height of one text line - Font Ascent
msgid "Height"
msgstr ""

#. TRN - Input label. Be short as possible
#. Copy surface of model on surface of the embossed text
#. TRN - Input label. Be short as possible
msgid "Use surface"
msgstr ""

#. TRN - Input label. Be short as possible
#. Option to change projection on curved surface
#. for each character(glyph) in text separately
msgid "Per glyph"
msgstr ""

#. TRN - Input label. Be short as possible
#. Align Top|Middle|Bottom and Left|Center|Right
msgid "Alignment"
msgstr ""

#. TRN - Input label. Be short as possible
msgid "Char gap"
msgstr ""

#. TRN - Input label. Be short as possible
msgid "Line gap"
msgstr ""

#. TRN - Input label. Be short as possible
msgid "Boldness"
msgstr ""

#. TRN - Input label. Be short as possible
#. Like Font italic
msgid "Skew ratio"
msgstr ""

#. TRN - Input label. Be short as possible
#. Distance from model surface to be able
#. move text as part fully into not flat surface
#. move text as modifier fully out of not flat surface
#. TRN - Input label. Be short as possible
msgid "From surface"
msgstr ""

#. TRN - Input label. Be short as possible
#. Keep vector from bottom to top of text aligned with printer Y axis
msgid "Keep up"
msgstr ""

#. TRN - Input label. Be short as possible.
#. Some Font file contain multiple fonts inside and
#. this is numerical selector of font inside font collections
msgid "Collection"
msgstr ""

#. TRN - Title in Undo/Redo stack after rotate with SVG around emboss axe
msgid "SVG rotate"
msgstr ""

#. TRN - Title in Undo/Redo stack after move with SVG along emboss axe - From surface
msgid "SVG move"
msgstr ""

msgid "Enter SVG gizmo"
msgstr ""

msgid "Leave SVG gizmo"
msgstr ""

msgid "SVG actions"
msgstr ""

msgid "SVG"
msgstr ""

#, boost-format
msgid "Opacity (%1%)"
msgstr ""

#, boost-format
msgid "Color gradient (%1%)"
msgstr ""

msgid "Undefined fill type"
msgstr ""

msgid "Linear gradient"
msgstr ""

msgid "Radial gradient"
msgstr ""

msgid "Open filled path"
msgstr ""

msgid "Undefined stroke type"
msgstr ""

msgid "Path can't be healed from self-intersection and multiple points."
msgstr ""

msgid ""
"Final shape contains self-intersection or multiple points with same "
"coordinate."
msgstr ""

#, boost-format
msgid "Shape is marked as invisible (%1%)."
msgstr ""

#. TRN: The first placeholder is shape identifier, the second is text describing the problem.
#, boost-format
msgid "Fill of shape (%1%) contains unsupported: %2%."
msgstr ""

#, boost-format
msgid "Stroke of shape (%1%) is too thin (minimal width is %2% mm)."
msgstr ""

#, boost-format
msgid "Stroke of shape (%1%) contains unsupported: %2%."
msgstr ""

msgid "Face the camera"
msgstr ""

#. TRN - Preview of filename after clear local filepath.
msgid "Unknown filename"
msgstr ""

#, boost-format
msgid "SVG file path is \"%1%\""
msgstr ""

msgid "Reload SVG file from disk."
msgstr ""

msgid "Change file"
msgstr ""

msgid "Change to another .svg file"
msgstr ""

msgid "Forget the file path"
msgstr ""

msgid ""
"Do NOT save local path to 3MF file.\n"
"Also disables 'reload from disk' option."
msgstr ""

#. TRN: An menu option to convert the SVG into an unmodifiable model part.
msgid "Bake"
msgstr ""

#. TRN: Tooltip for the menu item.
msgid "Bake into model as uneditable part"
msgstr ""

msgid "Save as"
msgstr ""

msgid "Save SVG file"
msgstr ""

msgid "Save as '.svg' file"
msgstr ""

msgid "Size in emboss direction."
msgstr ""

#. TRN: The placeholder contains a number.
#, boost-format
msgid "Scale also changes amount of curve samples (%1%)"
msgstr ""

msgid "Width of SVG."
msgstr ""

msgid "Height of SVG."
msgstr ""

msgid "Lock/unlock the aspect ratio of the SVG."
msgstr ""

msgid "Reset scale"
msgstr ""

msgid "Distance of the center of the SVG to the model surface."
msgstr ""

msgid "Reset distance"
msgstr ""

msgid "Reset rotation"
msgstr ""

msgid "Lock/unlock rotation angle when dragging above the surface."
msgstr ""

msgid "Mirror vertically"
msgstr ""

msgid "Mirror horizontally"
msgstr ""

#. TRN: This is the name of the action that shows in undo/redo stack (changing part type from SVG to something else).
msgid "Change SVG Type"
msgstr ""

#. TRN - Input label. Be short as possible
msgid "Mirror"
msgstr ""

msgid "Choose SVG file for emboss:"
msgstr ""

#, boost-format
msgid "File does NOT exist (%1%)."
msgstr ""

#, boost-format
msgid "Filename has to end with \".svg\" but you selected %1%"
msgstr ""

#, boost-format
msgid "Nano SVG parser can't load from file (%1%)."
msgstr ""

#, boost-format
msgid "SVG file does NOT contain a single path to be embossed (%1%)."
msgstr ""

msgid "No feature"
msgstr ""

msgid "Vertex"
msgstr ""

msgid "Edge"
msgstr ""

msgid "Plane"
msgstr ""

msgid "Point on edge"
msgstr ""

msgid "Point on circle"
msgstr ""

msgid "Point on plane"
msgstr ""

msgid "Center of edge"
msgstr ""

msgid "Center of circle"
msgstr ""

msgid "Select feature"
msgstr ""

msgid "Select point"
msgstr ""

msgid "Delete"
msgstr ""

msgid "Restart selection"
msgstr ""

msgid "Esc"
msgstr ""

msgid "Cancel a feature until exit"
msgstr ""

msgid "Measure"
msgstr ""

msgid ""
"Please confirm explosion ratio = 1, and please select at least one object."
msgstr ""

msgid "Please select at least one object."
msgstr ""

msgid "Edit to scale"
msgstr ""

msgctxt "Verb"
msgid "Scale all"
msgstr ""

msgid "None"
msgstr ""

msgid "Diameter"
msgstr ""

msgid "Length"
msgstr ""

msgid "Selection"
msgstr ""

msgid " (Moving)"
msgstr ""

msgid ""
"Select 2 faces on objects and \n"
" make objects assemble together."
msgstr ""

msgid ""
"Select 2 points or circles on objects and \n"
" specify distance between them."
msgstr ""

msgid "Face"
msgstr ""

msgid " (Fixed)"
msgstr ""

msgid "Point"
msgstr ""

msgid ""
"Feature 1 has been reset, \n"
"feature 2 has been feature 1"
msgstr ""

msgid "Warning: please select Plane's feature."
msgstr ""

msgid "Warning: please select Point's or Circle's feature."
msgstr ""

msgid "Warning: please select two different meshes."
msgstr ""

msgid "Copy to clipboard"
msgstr ""

msgid "Perpendicular distance"
msgstr ""

msgid "Distance"
msgstr ""

msgid "Direct distance"
msgstr ""

msgid "Distance XYZ"
msgstr ""

msgid "Parallel"
msgstr ""

msgid "Center coincidence"
msgstr ""

msgid "Feature 1"
msgstr ""

msgid "Reverse rotation"
msgstr ""

msgid "Rotate around center:"
msgstr ""

msgid "Parallel distance:"
msgstr ""

msgid "Flip by Face 2"
msgstr ""

msgid "Ctrl+"
msgstr ""

msgid "Notice"
msgstr ""

msgid "Undefined"
msgstr ""

#, boost-format
msgid "%1% was replaced with %2%"
msgstr ""

msgid "The configuration may be generated by a newer version of OrcaSlicer."
msgstr ""

msgid "Some values have been replaced. Please check them:"
msgstr ""

msgid "Process"
msgstr ""

msgid "Filament"
msgstr ""

msgid "Machine"
msgstr ""

msgid "Configuration package was loaded, but some values were not recognized."
msgstr ""
"The configuration package was loaded, but some values were not recognized."

#, boost-format
msgid ""
"Configuration file \"%1%\" was loaded, but some values were not recognized."
msgstr ""
"The configuration file “%1%” was loaded, but some values were not recognized."

msgid ""
"OrcaSlicer will terminate because of running out of memory. It may be a bug. "
"It will be appreciated if you report the issue to our team."
msgstr ""

msgid "Fatal error"
msgstr ""

msgid ""
"OrcaSlicer will terminate because of a localization error. It will be "
"appreciated if you report the specific scenario this issue happened."
msgstr ""

msgid "Critical error"
msgstr ""

#, boost-format
msgid "OrcaSlicer got an unhandled exception: %1%"
msgstr ""

msgid "Untitled"
msgstr ""

msgid "Downloading Bambu Network Plug-in"
msgstr ""

msgid "Login information expired. Please login again."
msgstr ""

msgid "Incorrect password"
msgstr ""

#, c-format, boost-format
msgid "Connect %s failed! [SN:%s, code=%s]"
msgstr ""

msgid ""
"Orca Slicer requires the Microsoft WebView2 Runtime to operate certain "
"features.\n"
"Click Yes to install it now."
msgstr ""

msgid "WebView2 Runtime"
msgstr ""

#, c-format, boost-format
msgid ""
"%s\n"
"Do you want to continue?"
msgstr ""

msgid "Remember my choice"
msgstr ""

msgid "Loading configuration"
msgstr ""

#, c-format, boost-format
msgid "Click to download new version in default browser: %s"
msgstr ""

msgid "The Orca Slicer needs an upgrade"
msgstr "Orca Slicer needs an update"

msgid "This is the newest version."
msgstr ""

msgid "Info"
msgstr ""

msgid ""
"The OrcaSlicer configuration file may be corrupted and cannot be parsed.\n"
"OrcaSlicer has attempted to recreate the configuration file.\n"
"Please note, application settings will be lost, but printer profiles will "
"not be affected."
msgstr ""

msgid "Rebuild"
msgstr ""

msgid "Loading current presets"
msgstr ""

msgid "Loading a mode view"
msgstr ""

msgid "Choose one file (3mf):"
msgstr ""

msgid "Choose one or more files (3mf/step/stl/svg/obj/amf/usd*/abc/ply):"
msgstr ""

msgid "Choose one or more files (3mf/step/stl/svg/obj/amf):"
msgstr ""

msgid "Choose ZIP file"
msgstr ""

msgid "Choose one file (gcode/3mf):"
msgstr ""

msgid "Some presets are modified."
msgstr ""

msgid ""
"You can keep the modified presets to the new project, discard or save "
"changes as new presets."
msgstr ""
"You can keep the modified presets for the new project, discard, or save "
"changes as new presets."

msgid "User logged out"
msgstr ""

msgid "new or open project file is not allowed during the slicing process!"
msgstr ""

msgid "Open Project"
msgstr ""

msgid ""
"The version of Orca Slicer is too low and needs to be updated to the latest "
"version before it can be used normally"
msgstr ""

msgid "Privacy Policy Update"
msgstr ""

msgid ""
"The number of user presets cached in the cloud has exceeded the upper limit, "
"newly created user presets can only be used locally."
msgstr ""

msgid "Sync user presets"
msgstr ""

msgid "Loading user preset"
msgstr ""

msgid "Switching application language"
msgstr ""

msgid "Select the language"
msgstr ""

msgid "Language"
msgstr ""

msgid "*"
msgstr ""

msgid "The uploads are still ongoing"
msgstr ""

msgid "Stop them and continue anyway?"
msgstr ""

msgid "Ongoing uploads"
msgstr ""

msgid "Select a G-code file:"
msgstr ""

msgid ""
"Could not start URL download. Destination folder is not set. Please choose "
"destination folder in Configuration Wizard."
msgstr ""

msgid "Import File"
msgstr ""

msgid "Choose files"
msgstr ""

msgid "New Folder"
msgstr ""

msgid "Open"
msgstr ""

msgid "Rename"
msgstr ""

msgid "Orca Slicer GUI initialization failed"
msgstr ""

#, boost-format
msgid "Fatal error, exception caught: %1%"
msgstr "Fatal error, exception: %1%"

msgid "Quality"
msgstr ""

msgid "Shell"
msgstr ""

msgid "Infill"
msgstr ""

msgid "Support"
msgstr ""

msgid "Flush options"
msgstr ""

msgid "Speed"
msgstr ""

msgid "Strength"
msgstr ""

msgid "Top Solid Layers"
msgstr "Top solid layers"

msgid "Top Minimum Shell Thickness"
msgstr "Top minimum shell thickness"

msgid "Bottom Solid Layers"
msgstr "Bottom solid layers"

msgid "Bottom Minimum Shell Thickness"
msgstr "Bottom minimum shell thickness"

msgid "Ironing"
msgstr ""

msgid "Fuzzy Skin"
msgstr "Fuzzy skin"

msgid "Extruders"
msgstr ""

msgid "Extrusion Width"
msgstr "Extrusion width"

msgid "Wipe options"
msgstr ""

msgid "Bed adhesion"
msgstr ""

msgid "Add part"
msgstr "Add Part"

msgid "Add negative part"
msgstr "Add Negative Part"

msgid "Add modifier"
msgstr "Add Modifier"

msgid "Add support blocker"
msgstr "Add Support Blocker"

msgid "Add support enforcer"
msgstr "Add Support Enforcer"

msgid "Add text"
msgstr ""

msgid "Add negative text"
msgstr ""

msgid "Add text modifier"
msgstr ""

msgid "Add SVG part"
msgstr ""

msgid "Add negative SVG"
msgstr ""

msgid "Add SVG modifier"
msgstr ""

msgid "Select settings"
msgstr ""

msgid "Hide"
msgstr ""

msgid "Show"
msgstr ""

msgid "Del"
msgstr ""

msgid "Delete the selected object"
msgstr ""

msgid "Load..."
msgstr ""

msgid "Cube"
msgstr ""

msgid "Cylinder"
msgstr ""

msgid "Cone"
msgstr ""

msgid "Disc"
msgstr ""

msgid "Torus"
msgstr ""

msgid "Orca Cube"
msgstr ""

msgid "3DBenchy"
msgstr ""

msgid "Autodesk FDM Test"
msgstr ""

msgid "Voron Cube"
msgstr ""

msgid "Stanford Bunny"
msgstr ""

msgid "Orca String Hell"
msgstr ""

msgid ""
"This model features text embossment on the top surface. For optimal results, "
"it is advisable to set the 'One Wall Threshold (min_width_top_surface)' to 0 "
"for the 'Only One Wall on Top Surfaces' to work best.\n"
"Yes - Change these settings automatically\n"
"No  - Do not change these settings for me"
msgstr ""

msgid "Text"
msgstr ""

msgid "Height range Modifier"
msgstr "Height Range Modifier"

msgid "Add settings"
msgstr "Add Settings"

msgid "Change type"
msgstr "Change Type"

msgid "Set as an individual object"
msgstr "Set as An Individual Object"

msgid "Set as individual objects"
msgstr "Set as Individual Objects"

msgid "Fill bed with copies"
msgstr ""

msgid "Fill the remaining area of bed with copies of the selected object"
msgstr ""

msgid "Printable"
msgstr ""

msgid "Fix model"
msgstr "Fix Model"

msgid "Export as one STL"
msgstr ""

msgid "Export as STLs"
msgstr ""

msgid "Reload from disk"
msgstr ""

msgid "Reload the selected parts from disk"
msgstr ""

msgid "Replace with STL"
msgstr ""

msgid "Replace the selected part with new STL"
msgstr ""

msgid "Change filament"
msgstr ""

msgid "Set filament for selected items"
msgstr ""

msgid "Default"
msgstr ""

#, c-format, boost-format
msgid "Filament %d"
msgstr ""

msgid "current"
msgstr ""

msgid "Scale to build volume"
msgstr ""

msgid "Scale an object to fit the build volume"
msgstr ""

msgid "Flush Options"
msgstr ""

msgid "Flush into objects' infill"
msgstr ""

msgid "Flush into this object"
msgstr ""

msgid "Flush into objects' support"
msgstr ""

msgid "Edit in Parameter Table"
msgstr ""

msgid "Convert from inches"
msgstr "Convert from Inches"

msgid "Restore to inches"
msgstr "Restore to Inch"

msgid "Convert from meters"
msgstr "Convert from Meters"

msgid "Restore to meters"
msgstr "Restore to Meter"

msgid "Assemble"
msgstr ""

msgid "Assemble the selected objects to an object with multiple parts"
msgstr "Assemble the selected objects into an object with multiple parts"

msgid "Assemble the selected objects to an object with single part"
msgstr "Assemble the selected objects into an object with single part"

msgid "Mesh boolean"
msgstr ""

msgid "Mesh boolean operations including union and subtraction"
msgstr ""

msgid "Along X axis"
msgstr "Along X Axis"

msgid "Mirror along the X axis"
msgstr "Mirror along the X Axis"

msgid "Along Y axis"
msgstr "Along Y Axis"

msgid "Mirror along the Y axis"
msgstr "Mirror along the Y Axis"

msgid "Along Z axis"
msgstr "Along Z Axis"

msgid "Mirror along the Z axis"
msgstr "Mirror along the Z Axis"

msgid "Mirror object"
msgstr ""

msgid "Edit text"
msgstr ""

msgid "Ability to change text, font, size, ..."
msgstr ""

msgid "Edit SVG"
msgstr ""

msgid "Change SVG source file, projection, size, ..."
msgstr ""

msgid "Invalidate cut info"
msgstr ""

msgid "Add Primitive"
msgstr ""

msgid "Add Handy models"
msgstr ""

msgid "Add Models"
msgstr ""

msgid "Show Labels"
msgstr ""

msgid "To objects"
msgstr "To Objects"

msgid "Split the selected object into multiple objects"
msgstr ""

msgid "To parts"
msgstr "To Parts"

msgid "Split the selected object into multiple parts"
msgstr ""

msgid "Split"
msgstr ""

msgid "Split the selected object"
msgstr ""

msgid "Auto orientation"
msgstr ""

msgid "Auto orient the object to improve print quality."
msgstr ""

msgid "Select All"
msgstr ""

msgid "select all objects on current plate"
msgstr "Select all objects on the current plate"

msgid "Delete All"
msgstr ""

msgid "delete all objects on current plate"
msgstr "Delete all objects on the current plate"

msgid "Arrange"
msgstr ""

msgid "arrange current plate"
msgstr "Arrange current plate"

msgid "Reload All"
msgstr ""

msgid "reload all from disk"
msgstr ""

msgid "Auto Rotate"
msgstr ""

msgid "auto rotate current plate"
msgstr "Auto rotate current plate"

msgid "Delete Plate"
msgstr ""

msgid "Remove the selected plate"
msgstr ""

msgid "Clone"
msgstr ""

msgid "Simplify Model"
msgstr ""

msgid "Center"
msgstr ""

msgid "Drop"
msgstr ""

msgid "Edit Process Settings"
msgstr ""

msgid "Edit print parameters for a single object"
msgstr ""

msgid "Change Filament"
msgstr ""

msgid "Set Filament for selected items"
msgstr ""

msgid "Unlock"
msgstr ""

msgid "Lock"
msgstr ""

msgid "Edit Plate Name"
msgstr ""

msgid "Name"
msgstr ""

msgid "Fila."
msgstr ""

#, c-format, boost-format
msgid "%1$d error repaired"
msgid_plural "%1$d errors repaired"
msgstr[0] ""
msgstr[1] ""

#, c-format, boost-format
msgid "Error: %1$d non-manifold edge."
msgid_plural "Error: %1$d non-manifold edges."
msgstr[0] ""
msgstr[1] ""

msgid "Remaining errors"
msgstr ""

#, c-format, boost-format
msgid "%1$d non-manifold edge"
msgid_plural "%1$d non-manifold edges"
msgstr[0] ""
msgstr[1] ""

msgid "Right click the icon to fix model object"
msgstr ""

msgid "Right button click the icon to drop the object settings"
msgstr "Right click the icon to drop the object settings"

msgid "Click the icon to reset all settings of the object"
msgstr ""

msgid "Right button click the icon to drop the object printable property"
msgstr "Right click the icon to drop the object printable property"

msgid "Click the icon to toggle printable property of the object"
msgstr "Click the icon to toggle printable properties of the object"

msgid "Click the icon to edit support painting of the object"
msgstr ""

msgid "Click the icon to edit color painting of the object"
msgstr "Click the icon to edit color painting for the object"

msgid "Click the icon to shift this object to the bed"
msgstr ""

msgid "Loading file"
msgstr ""

msgid "Error!"
msgstr ""

msgid "Failed to get the model data in the current file."
msgstr ""

msgid "Generic"
msgstr ""

msgid "Add Modifier"
msgstr ""

msgid "Switch to per-object setting mode to edit modifier settings."
msgstr ""

msgid ""
"Switch to per-object setting mode to edit process settings of selected "
"objects."
msgstr ""

msgid "Delete connector from object which is a part of cut"
msgstr ""

msgid "Delete solid part from object which is a part of cut"
msgstr ""

msgid "Delete negative volume from object which is a part of cut"
msgstr ""

msgid ""
"To save cut correspondence you can delete all connectors from all related "
"objects."
msgstr ""

msgid ""
"This action will break a cut correspondence.\n"
"After that model consistency can't be guaranteed.\n"
"\n"
"To manipulate with solid parts or negative volumes you have to invalidate "
"cut information first."
msgstr ""
"This action will break a cut correspondence.\n"
"After that, model consistency can't be guaranteed.\n"
"\n"
"To manipulate with solid parts or negative volumes you have to invalidate "
"cut information first."

msgid "Delete all connectors"
msgstr ""

msgid "Deleting the last solid part is not allowed."
msgstr ""

msgid "The target object contains only one part and cannot be split."
msgstr ""

msgid "Assembly"
msgstr ""

msgid "Cut Connectors information"
msgstr ""

msgid "Object manipulation"
msgstr ""

msgid "Group manipulation"
msgstr ""

msgid "Object Settings to modify"
msgstr "Object Settings to Modify"

msgid "Part Settings to modify"
msgstr "Part Settings to Modify"

msgid "Layer range Settings to modify"
msgstr "Layer Range Settings to Modify"

msgid "Part manipulation"
msgstr ""

msgid "Instance manipulation"
msgstr ""

msgid "Height ranges"
msgstr ""

msgid "Settings for height range"
msgstr ""

msgid "Layer"
msgstr ""

msgid "Selection conflicts"
msgstr ""

msgid ""
"If the first selected item is an object, the second should also be an object."
msgstr ""

msgid ""
"If the first selected item is a part, the second should be a part in the "
"same object."
msgstr ""

msgid "The type of the last solid object part is not to be changed."
msgstr "The type of the last solid object part cannot be changed."

msgid "Negative Part"
msgstr ""

msgid "Support Blocker"
msgstr ""

msgid "Support Enforcer"
msgstr ""

msgid "Type:"
msgstr ""

msgid "Choose part type"
msgstr ""

msgid "Enter new name"
msgstr ""

msgid "Renaming"
msgstr ""

msgid "Following model object has been repaired"
msgid_plural "Following model objects have been repaired"
msgstr[0] "The following model object has been repaired"
msgstr[1] "The following model objects have been repaired"

msgid "Failed to repair following model object"
msgid_plural "Failed to repair following model objects"
msgstr[0] "Failed to repair the following model object"
msgstr[1] "Failed to repair the following model objects"

msgid "Repairing was canceled"
msgstr ""

msgid "Additional process preset"
msgstr ""

msgid "Remove parameter"
msgstr ""

msgid "to"
msgstr ""

msgid "Remove height range"
msgstr ""

msgid "Add height range"
msgstr ""

msgid "Invalid numeric."
msgstr ""

msgid "one cell can only be copied to one or multiple cells in the same column"
msgstr "One cell can only be copied to one or more cells in the same column."

msgid "Copying multiple cells is not supported."
msgstr ""

msgid "Outside"
msgstr ""

msgid "Layer height"
msgstr ""

msgid "Wall loops"
msgstr ""

msgid "Infill density(%)"
msgstr ""

msgid "Auto Brim"
msgstr ""

msgid "Mouse ear"
msgstr ""

msgid "Outer brim only"
msgstr ""

msgid "Inner brim only"
msgstr ""

msgid "Outer and inner brim"
msgstr ""

msgid "No-brim"
msgstr ""

msgid "Outer wall speed"
msgstr ""

msgid "Plate"
msgstr ""

msgid "Brim"
msgstr ""

msgid "Object/Part Setting"
msgstr "Object/part setting"

msgid "Reset parameter"
msgstr ""

msgid "Multicolor Print"
msgstr ""

msgid "Line Type"
msgstr ""

msgid "More"
msgstr ""

msgid "Open Preferences."
msgstr "Open Preferences"

msgid "Open next tip."
msgstr "Open next tip"

msgid "Open Documentation in web browser."
msgstr "Open documentation in web browser"

msgid "Color"
msgstr ""

msgid "Pause"
msgstr ""

msgid "Template"
msgstr ""

msgid "Custom"
msgstr ""

msgid "Pause:"
msgstr ""

msgid "Custom Template:"
msgstr ""

msgid "Custom G-code:"
msgstr ""

msgid "Custom G-code"
msgstr ""

msgid "Enter Custom G-code used on current layer:"
msgstr ""

msgid "Jump to Layer"
msgstr "Jump to layer"

msgid "Please enter the layer number"
msgstr "Please enter the layer number."

msgid "Add Pause"
msgstr ""

msgid "Insert a pause command at the beginning of this layer."
msgstr ""

msgid "Add Custom G-code"
msgstr ""

msgid "Insert custom G-code at the beginning of this layer."
msgstr ""

msgid "Add Custom Template"
msgstr ""

msgid "Insert template custom G-code at the beginning of this layer."
msgstr ""

msgid "Filament "
msgstr ""

msgid "Change filament at the beginning of this layer."
msgstr ""

msgid "Delete Pause"
msgstr ""

msgid "Delete Custom Template"
msgstr ""

msgid "Edit Custom G-code"
msgstr ""

msgid "Delete Custom G-code"
msgstr ""

msgid "Delete Filament Change"
msgstr ""

msgid "No printer"
msgstr ""

msgid "..."
msgstr ""

msgid "Failed to connect to the server"
msgstr ""

msgid "Check the status of current system services"
msgstr ""

msgid "code"
msgstr ""

msgid "Failed to connect to cloud service"
msgstr ""

msgid "Please click on the hyperlink above to view the cloud service status"
msgstr ""

msgid "Failed to connect to the printer"
msgstr ""

msgid "Connection to printer failed"
msgstr ""

msgid "Please check the network connection of the printer and Orca."
msgstr ""

msgid "Connecting..."
msgstr ""

msgid "?"
msgstr ""

msgid "/"
msgstr ""

msgid "Empty"
msgstr ""

msgid "AMS"
msgstr ""

msgid "Auto Refill"
msgstr ""

msgid "AMS not connected"
msgstr ""

msgid "Load"
msgstr ""

msgid "Unload"
msgstr ""

msgid "Ext Spool"
msgstr ""

msgid "Tips"
msgstr ""

msgid "Guide"
msgstr ""

msgid "Retry"
msgstr ""

msgid "Calibrating AMS..."
msgstr ""

msgid "A problem occurred during calibration. Click to view the solution."
msgstr ""

msgid "Calibrate again"
msgstr ""

msgid "Cancel calibration"
msgstr ""

msgid "Idling..."
msgstr ""

msgid "Heat the nozzle"
msgstr ""

msgid "Cut filament"
msgstr ""

msgid "Pull back current filament"
msgstr "Pull back the current filament"

msgid "Push new filament into extruder"
msgstr ""

msgid "Purge old filament"
msgstr ""

msgid "Feed Filament"
msgstr ""

msgid "Confirm extruded"
msgstr ""

msgid "Check filament location"
msgstr ""

msgid "Grab new filament"
msgstr ""

msgid ""
"Choose an AMS slot then press \"Load\" or \"Unload\" button to automatically "
"load or unload filaments."
msgstr ""
"Choose an AMS slot then press \"Load\" or \"Unload\" button to automatically "
"load or unload filament."

msgid "Edit"
msgstr ""

msgid ""
"All the selected objects are on a locked plate.\n"
"Cannot auto-arrange these objects."
msgstr ""

msgid "No arrangeable objects are selected."
msgstr ""

msgid ""
"This plate is locked.\n"
"Cannot auto-arrange on this plate."
msgstr ""

msgid "Arranging..."
msgstr ""

msgid "Arranging"
msgstr ""

msgid "Arranging canceled."
msgstr ""

msgid ""
"Arranging is done but there are unpacked items. Reduce spacing and try again."
msgstr ""
"Arranging complete, but some items were not able to be arranged. Reduce "
"spacing and try again."

msgid "Arranging done."
msgstr ""

msgid ""
"Arrange failed. Found some exceptions when processing object geometries."
msgstr ""

#, c-format, boost-format
msgid ""
"Arrangement ignored the following objects which can't fit into a single "
"bed:\n"
"%s"
msgstr ""

msgid ""
"All the selected objects are on a locked plate.\n"
"Cannot auto-orient these objects."
msgstr ""

msgid ""
"This plate is locked.\n"
"Cannot auto-orient on this plate."
msgstr ""

msgid "Orienting..."
msgstr ""

msgid "Orienting"
msgstr ""

msgid "Orienting canceled."
msgstr ""

msgid "Filling"
msgstr ""

msgid "Bed filling canceled."
msgstr ""

msgid "Bed filling done."
msgstr ""

msgid "Searching for optimal orientation"
msgstr ""

msgid "Orientation search canceled."
msgstr ""

msgid "Orientation found."
msgstr ""

msgid "Logging in"
msgstr ""

msgid "Login failed"
msgstr ""

msgid "Please check the printer network connection."
msgstr ""

msgid "Abnormal print file data. Please slice again."
msgstr "Abnormal print file data: please slice again."

msgid "Task canceled."
msgstr ""

msgid "Upload task timed out. Please check the network status and try again."
msgstr ""

msgid "Cloud service connection failed. Please try again."
msgstr ""

msgid "Print file not found. Please slice again."
msgstr "Print file not found; please slice again."

msgid ""
"The print file exceeds the maximum allowable size (1GB). Please simplify the "
"model and slice again."
msgstr ""

msgid "Failed to send the print job. Please try again."
msgstr ""

msgid "Failed to upload file to ftp. Please try again."
msgstr ""

msgid ""
"Check the current status of the bambu server by clicking on the link above."
msgstr ""
"Check the current status of the Bambu Lab server by clicking on the link "
"above."

msgid ""
"The size of the print file is too large. Please adjust the file size and try "
"again."
msgstr ""

msgid "Print file not found, please slice it again and send it for printing."
msgstr "Print file not found; please slice it again and send it for printing."

msgid ""
"Failed to upload print file to FTP. Please check the network status and try "
"again."
msgstr ""
"Failed to upload print file via FTP. Please check the network status and try "
"again."

msgid "Sending print job over LAN"
msgstr ""

msgid "Sending print job through cloud service"
msgstr ""

msgid "Print task sending times out."
msgstr ""

msgid "Service Unavailable"
msgstr ""

msgid "Unknown Error."
msgstr ""

msgid "Sending print configuration"
msgstr ""

#, c-format, boost-format
msgid "Successfully sent. Will automatically jump to the device page in %ss"
msgstr ""

#, c-format, boost-format
msgid "Successfully sent. Will automatically jump to the next page in %ss"
msgstr ""

msgid "An SD card needs to be inserted before printing via LAN."
msgstr "A MicroSD card needs to be inserted before printing via LAN."

msgid "Sending G-code file over LAN"
msgstr ""

msgid "Sending G-code file to SD card"
msgstr "Sending G-code file to MicroSD card"

#, c-format, boost-format
msgid "Successfully sent. Close current page in %s s"
msgstr ""

msgid "An SD card needs to be inserted before sending to printer."
msgstr "A MicroSD card needs to be inserted before sending to printer."

msgid "Importing SLA archive"
msgstr ""

msgid ""
"The SLA archive doesn't contain any presets. Please activate some SLA "
"printer preset first before importing that SLA archive."
msgstr ""
"The SLA archive doesn't contain any presets. Please activate some SLA "
"printer presets first before importing that SLA archive."

msgid "Importing canceled."
msgstr ""

msgid "Importing done."
msgstr ""

msgid ""
"The imported SLA archive did not contain any presets. The current SLA "
"presets were used as fallback."
msgstr ""

msgid "You cannot load SLA project with a multi-part object on the bed"
msgstr "You cannot load an SLA project with a multi-part object on the bed"

msgid "Please check your object list before preset changing."
msgstr ""

msgid "Attention!"
msgstr ""

msgid "Downloading"
msgstr ""

msgid "Download failed"
msgstr ""

msgid "Canceled"
msgstr ""

msgid "Installed successfully"
msgstr ""

msgid "Installing"
msgstr ""

msgid "Install failed"
msgstr ""

msgid "Portions copyright"
msgstr "License Info"

msgid "Copyright"
msgstr ""

msgid "License"
msgstr ""

msgid "Orca Slicer is licensed under "
msgstr ""

msgid "GNU Affero General Public License, version 3"
msgstr ""

msgid "Orca Slicer is based on PrusaSlicer and BambuStudio"
msgstr ""

msgid "Libraries"
msgstr ""

msgid ""
"This software uses open source components whose copyright and other "
"proprietary rights belong to their respective owners"
msgstr ""

#, c-format, boost-format
msgid "About %s"
msgstr ""

msgid "OrcaSlicer is based on BambuStudio, PrusaSlicer, and SuperSlicer."
msgstr ""

msgid "BambuStudio is originally based on PrusaSlicer by PrusaResearch."
msgstr ""

msgid "PrusaSlicer is originally based on Slic3r by Alessandro Ranellucci."
msgstr ""

msgid ""
"Slic3r was created by Alessandro Ranellucci with the help of many other "
"contributors."
msgstr ""

msgid "Version"
msgstr ""

msgid "AMS Materials Setting"
msgstr ""

msgid "Confirm"
msgstr ""

msgid "Close"
msgstr ""

msgid ""
"Nozzle\n"
"Temperature"
msgstr ""

msgid "max"
msgstr ""

msgid "min"
msgstr ""

#, boost-format
msgid "The input value should be greater than %1% and less than %2%"
msgstr ""

msgid "SN"
msgstr ""

msgid "Factors of Flow Dynamics Calibration"
msgstr ""

msgid "PA Profile"
msgstr ""

msgid "Factor K"
msgstr ""

msgid "Factor N"
msgstr ""

msgid "Setting AMS slot information while printing is not supported"
msgstr ""

msgid "Setting Virtual slot information while printing is not supported"
msgstr ""

msgid "Are you sure you want to clear the filament information?"
msgstr ""

msgid "You need to select the material type and color first."
msgstr ""

#, c-format, boost-format
msgid "Please input a valid value (K in %.1f~%.1f)"
msgstr ""

#, c-format, boost-format
msgid "Please input a valid value (K in %.1f~%.1f, N in %.1f~%.1f)"
msgstr ""

msgid "Other Color"
msgstr ""

msgid "Custom Color"
msgstr ""

msgid "Dynamic flow calibration"
msgstr ""

msgid ""
"The nozzle temp and max volumetric speed will affect the calibration "
"results. Please fill in the same values as the actual printing. They can be "
"auto-filled by selecting a filament preset."
msgstr ""

msgid "Nozzle Diameter"
msgstr ""

msgid "Bed Type"
msgstr "Plate Type"

msgid "Nozzle temperature"
msgstr ""

msgid "Bed Temperature"
msgstr ""

msgid "Max volumetric speed"
msgstr ""

msgid "℃"
msgstr ""

msgid "Bed temperature"
msgstr ""

msgid "mm³"
msgstr ""

msgid "Start calibration"
msgstr "Start"

msgid "Next"
msgstr ""

msgid ""
"Calibration completed. Please find the most uniform extrusion line on your "
"hot bed like the picture below, and fill the value on its left side into the "
"factor K input box."
msgstr ""

msgid "Save"
msgstr ""

msgid "Last Step"
msgstr "Back"

msgid "Example"
msgstr ""

#, c-format, boost-format
msgid "Calibrating... %d%%"
msgstr ""

msgid "Calibration completed"
msgstr ""

#, c-format, boost-format
msgid "%s does not support %s"
msgstr ""

msgid "Dynamic flow Calibration"
msgstr "Dynamic flow calibration"

msgid "Step"
msgstr ""

msgid "AMS Slots"
msgstr ""

msgid ""
"Note: Only the AMS slots loaded with the same material type can be selected."
msgstr ""

msgid "Enable AMS"
msgstr ""

msgid "Print with filaments in the AMS"
msgstr "Print with filament in the AMS"

msgid "Disable AMS"
msgstr ""

msgid "Print with the filament mounted on the back of chassis"
msgstr "Print with filament on external spool"

msgid "Current AMS humidity"
msgstr ""

msgid ""
"Please change the desiccant when it is too wet. The indicator may not "
"represent accurately in following cases: when the lid is open or the "
"desiccant pack is changed. It take hours to absorb the moisture, and low "
"temperatures also slow down the process."
msgstr ""
"Please change the desiccant when it is too wet. The indicator may not "
"represent accurately in following cases: when the lid is open or the "
"desiccant pack is changed. It takes a few hours to absorb the moisture, and "
"low temperatures also slow down the process."

msgid ""
"Configure which AMS slot should be used for a filament used in the print job."
msgstr ""

msgid "Filament used in this print job"
msgstr ""

msgid "AMS slot used for this filament"
msgstr ""

msgid "Click to select AMS slot manually"
msgstr ""

msgid "Do not Enable AMS"
msgstr ""

msgid "Print using materials mounted on the back of the case"
msgstr "Print using filament on external spool."

msgid "Print with filaments in AMS"
msgstr "Print with filament in AMS"

msgid "Print with filaments mounted on the back of the chassis"
msgstr "Print with filament on external spool"

msgid ""
"When the current material run out, the printer will continue to print in the "
"following order."
msgstr ""

msgid "Group"
msgstr ""

msgid "The printer does not currently support auto refill."
msgstr ""

msgid ""
"AMS filament backup is not enabled, please enable it in the AMS settings."
msgstr ""
"AMS filament backup is not enabled; please enable it in the AMS settings."

msgid ""
"If there are two identical filaments in AMS, AMS filament backup will be "
"enabled.\n"
"(Currently supporting automatic supply of consumables with the same brand, "
"material type, and color)"
msgstr ""
"If there are two identical filaments in an AMS, AMS filament backup will be "
"enabled.\n"
"(This currently supports automatic supply of consumables with the same "
"brand, material type, and color)"

msgid "DRY"
msgstr ""

msgid "WET"
msgstr ""

msgid "AMS Settings"
msgstr ""

msgid "Insertion update"
msgstr ""

msgid ""
"The AMS will automatically read the filament information when inserting a "
"new Bambu Lab filament. This takes about 20 seconds."
msgstr ""
"The AMS will automatically read the filament information when inserting a "
"new Bambu Lab filament spool. This takes about 20 seconds."

msgid ""
"Note: if a new filament is inserted during printing, the AMS will not "
"automatically read any information until printing is completed."
msgstr ""

msgid ""
"When inserting a new filament, the AMS will not automatically read its "
"information, leaving it blank for you to enter manually."
msgstr ""

msgid "Power on update"
msgstr "Update on startup"

msgid ""
"The AMS will automatically read the information of inserted filament on "
"start-up. It will take about 1 minute. The reading process will roll the "
"filament spools."
msgstr ""
"The AMS will automatically read the information of inserted filament on "
"start-up. It will take about 1 minute. The reading process will rotate the "
"filament spools."

msgid ""
"The AMS will not automatically read information from inserted filament "
"during startup and will continue to use the information recorded before the "
"last shutdown."
msgstr ""

msgid "Update remaining capacity"
msgstr ""

msgid ""
"The AMS will estimate Bambu filament's remaining capacity after the filament "
"info is updated. During printing, remaining capacity will be updated "
"automatically."
msgstr ""

msgid "AMS filament backup"
msgstr ""

msgid ""
"AMS will continue to another spool with matching filament properties "
"automatically when current filament runs out."
msgstr ""

msgid "Air Printing Detection"
msgstr ""

msgid ""
"Detects clogging and filament grinding, halting printing immediately to "
"conserve time and filament."
msgstr ""

msgid "File"
msgstr ""

msgid "Calibration"
msgstr ""

msgid ""
"Failed to download the plug-in. Please check your firewall settings and vpn "
"software, check and retry."
msgstr ""
"Failed to download the plug-in. Please check your firewall settings and vpn "
"software and retry."

msgid ""
"Failed to install the plug-in. Please check whether it is blocked or deleted "
"by anti-virus software."
msgstr ""
"Failed to install the plug-in. Please check whether it is blocked or has "
"been deleted by anti-virus software."

msgid "click here to see more info"
msgstr ""

msgid "Please home all axes (click "
msgstr ""

msgid ""
") to locate the toolhead's position. This prevents device moving beyond the "
"printable boundary and causing equipment wear."
msgstr ""

msgid "Go Home"
msgstr ""

msgid ""
"A error occurred. Maybe memory of system is not enough or it's a bug of the "
"program"
msgstr ""
"An error occurred. The system may have run out of memory, or a bug may have "
"occurred."

#, boost-format
msgid "A fatal error occurred: \"%1%\""
msgstr ""

msgid "Please save project and restart the program."
msgstr "Please save your project and restart the application."

msgid "Processing G-code from Previous file..."
msgstr "Processing G-Code from previous file…"

msgid "Slicing complete"
msgstr ""

msgid "Access violation"
msgstr ""

msgid "Illegal instruction"
msgstr ""

msgid "Divide by zero"
msgstr ""

msgid "Overflow"
msgstr ""

msgid "Underflow"
msgstr ""

msgid "Floating reserved operand"
msgstr ""

msgid "Stack overflow"
msgstr ""

msgid "Running post-processing scripts"
msgstr ""

msgid "Successfully executed post-processing script"
msgstr ""

msgid "Unknown error occurred during exporting G-code."
msgstr ""

#, boost-format
msgid ""
"Copying of the temporary G-code to the output G-code failed. Maybe the SD "
"card is write locked?\n"
"Error message: %1%"
msgstr ""

#, boost-format
msgid ""
"Copying of the temporary G-code to the output G-code failed. There might be "
"problem with target device, please try exporting again or using different "
"device. The corrupted output G-code is at %1%.tmp."
msgstr ""

#, boost-format
msgid ""
"Renaming of the G-code after copying to the selected destination folder has "
"failed. Current path is %1%.tmp. Please try exporting again."
msgstr ""

#, boost-format
msgid ""
"Copying of the temporary G-code has finished but the original code at %1% "
"couldn't be opened during copy check. The output G-code is at %2%.tmp."
msgstr ""

#, boost-format
msgid ""
"Copying of the temporary G-code has finished but the exported code couldn't "
"be opened during copy check. The output G-code is at %1%.tmp."
msgstr ""

#, boost-format
msgid "G-code file exported to %1%"
msgstr ""

msgid "Unknown error when exporting G-code."
msgstr "Unknown error with G-code export"

#, boost-format
msgid ""
"Failed to save G-code file.\n"
"Error message: %1%.\n"
"Source file %2%."
msgstr ""

msgid "Copying of the temporary G-code to the output G-code failed"
msgstr "Copying of the temporary G-code to the output G-code failed."

#, boost-format
msgid "Scheduling upload to `%1%`. See Window -> Print Host Upload Queue"
msgstr ""

msgid "Device"
msgstr ""

msgid "Task Sending"
msgstr ""

msgid "Task Sent"
msgstr ""

msgid "Edit multiple printers"
msgstr ""

msgid "Select connected printers (0/6)"
msgstr ""

#, c-format, boost-format
msgid "Select Connected Printers (%d/6)"
msgstr ""

#, c-format, boost-format
msgid "The maximum number of printers that can be selected is %d"
msgstr ""

msgid "Offline"
msgstr ""

msgid "No task"
msgstr ""

msgid "View"
msgstr ""

msgid "N/A"
msgstr ""

msgid "Edit Printers"
msgstr ""

msgid "Device Name"
msgstr ""

msgid "Task Name"
msgstr ""

msgid "Device Status"
msgstr ""

msgid "Actions"
msgstr ""

msgid ""
"Please select the devices you would like to manage here (up to 6 devices)"
msgstr ""

msgid "Add"
msgstr ""

msgid "Idle"
msgstr ""

msgid "Printing"
msgstr ""

msgid "Upgrading"
msgstr ""

msgid "Incompatible"
msgstr ""

msgid "syncing"
msgstr ""

msgid "Printing Finish"
msgstr ""

msgid "Printing Failed"
msgstr ""

msgid "Printing Pause"
msgstr ""

msgid "Prepare"
msgstr ""

msgid "Slicing"
msgstr ""

msgid "Pending"
msgstr ""

msgid "Sending"
msgstr ""

msgid "Sending Finish"
msgstr ""

msgid "Sending Cancel"
msgstr ""

msgid "Sending Failed"
msgstr ""

msgid "Print Success"
msgstr ""

msgid "Print Failed"
msgstr ""

msgid "Removed"
msgstr ""

msgid "Resume"
msgstr ""

msgid "Stop"
msgstr ""

msgid "Task Status"
msgstr ""

msgid "Sent Time"
msgstr ""

msgid "There are no tasks to be sent!"
msgstr ""

msgid "No historical tasks!"
msgstr ""

msgid "Loading..."
msgstr ""

msgid "No AMS"
msgstr ""

msgid "Send to Multi-device"
msgstr ""

msgid "Preparing print job"
msgstr ""

msgid "Abnormal print file data. Please slice again"
msgstr ""

msgid "There is no device available to send printing."
msgstr ""

msgid "The number of printers in use simultaneously cannot be equal to 0."
msgstr ""

msgid "Use External Spool"
msgstr ""

msgid "Use AMS"
msgstr ""

msgid "Select Printers"
msgstr ""

msgid "AMS Status"
msgstr ""

msgid "Printing Options"
msgstr ""

msgid "Bed Leveling"
msgstr "Bed leveling"

msgid "Timelapse"
msgstr ""

msgid "Flow Dynamic Calibration"
msgstr ""

msgid "Send Options"
msgstr ""

msgid "Send to"
msgstr ""

msgid ""
"printers at the same time. (It depends on how many devices can undergo "
"heating at the same time.)"
msgstr ""

msgid "Wait"
msgstr ""

msgid ""
"minute each batch. (It depends on how long it takes to complete the heating.)"
msgstr ""
"minute each batch. (It depends on how long it takes to complete heating.)"

msgid "Send"
msgstr ""

msgid "Name is invalid;"
msgstr ""

msgid "illegal characters:"
msgstr "Illegal characters:"

msgid "illegal suffix:"
msgstr "Illegal suffix:"

msgid "The name is not allowed to be empty."
msgstr "The name field is not allowed to be empty."

msgid "The name is not allowed to start with space character."
msgstr "The name is not allowed to start with a space."

msgid "The name is not allowed to end with space character."
msgstr "The name is not allowed to end with a space."

msgid "The name length exceeds the limit."
msgstr ""

msgid "Origin"
msgstr ""

msgid "Size in X and Y of the rectangular plate."
msgstr ""

msgid ""
"Distance of the 0,0 G-code coordinate from the front left corner of the "
"rectangle."
msgstr ""

msgid ""
"Diameter of the print bed. It is assumed that origin (0,0) is located in the "
"center."
msgstr ""

msgid "Rectangular"
msgstr ""

msgid "Circular"
msgstr ""

msgid "Load shape from STL..."
msgstr ""

msgid "Settings"
msgstr ""

msgid "Texture"
msgstr ""

msgid "Remove"
msgstr ""

msgid "Not found:"
msgstr ""

msgid "Model"
msgstr ""

msgid "Choose an STL file to import bed shape from:"
msgstr ""

msgid "Invalid file format."
msgstr ""

msgid "Error! Invalid model"
msgstr "Error: invalid model"

msgid "The selected file contains no geometry."
msgstr ""

msgid ""
"The selected file contains several disjoint areas. This is not supported."
msgstr ""
"The selected file contains several disjointed areas. This is not supported."

msgid "Choose a file to import bed texture from (PNG/SVG):"
msgstr ""

msgid "Choose an STL file to import bed model from:"
msgstr ""

msgid "Bed Shape"
msgstr ""

msgid ""
"The recommended minimum temperature is less than 190°C or the "
"recommended maximum temperature is greater than 300°C.\n"
msgstr ""

msgid ""
"The recommended minimum temperature cannot be higher than the recommended "
"maximum temperature.\n"
msgstr ""

msgid "Please check.\n"
msgstr ""

msgid ""
"Nozzle may be blocked when the temperature is out of recommended range.\n"
"Please make sure whether to use the temperature to print.\n"
"\n"
msgstr ""
"The nozzle may become clogged when the temperature is out of the recommended "
"range.\n"
"Please make sure whether to use this temperature to print.\n"
"\n"

#, c-format, boost-format
msgid ""
"The recommended nozzle temperature for this filament type is [%d, %d] "
"degrees Celsius."
msgstr ""

msgid ""
"Too small max volumetric speed.\n"
"Reset to 0.5"
msgstr ""
"Too small max volumetric speed.\n"
"Value was reset to 0.5"

#, c-format, boost-format
msgid ""
"Current chamber temperature is higher than the material's safe temperature, "
"this may result in material softening and clogging. The maximum safe "
"temperature for the material is %d"
msgstr ""
"Current chamber temperature is higher than the material's safe temperature; "
"this may result in material softening and nozzle clogs. The maximum safe "
"temperature for the material is %d"

msgid ""
"Too small layer height.\n"
"Reset to 0.2"
msgstr ""
"Layer height too small\n"
"It has been reset to 0.2"

msgid ""
"Too small ironing spacing.\n"
"Reset to 0.1"
msgstr ""
"Ironing spacing too small\n"
"It has been reset to 0.1"

msgid ""
"Zero initial layer height is invalid.\n"
"\n"
"The first layer height will be reset to 0.2."
msgstr ""
"Zero first layer height is invalid.\n"
"\n"
"The first layer height will be reset to 0.2."

msgid ""
"This setting is only used for model size tunning with small value in some "
"cases.\n"
"For example, when model size has small error and hard to be assembled.\n"
"For large size tuning, please use model scale function.\n"
"\n"
"The value will be reset to 0."
msgstr ""
"This setting is only used for tuning model size by small amounts.\n"
"For example, when the model size has small errors or when tolerances are "
"incorrect. For large adjustments, please use the model scale function.\n"
"\n"
"The value will be reset to 0."

msgid ""
"Too large elephant foot compensation is unreasonable.\n"
"If really have serious elephant foot effect, please check other settings.\n"
"For example, whether bed temperature is too high.\n"
"\n"
"The value will be reset to 0."
msgstr ""
"The elephant foot compensation value is too large.\n"
"If there are significant elephant foot issues, please check other settings.\n"
"The bed temperature may be too high, for example.\n"
"\n"
"The value will be reset to 0."

msgid ""
"Alternate extra wall does't work well when ensure vertical shell thickness "
"is set to All."
msgstr ""

msgid ""
"Change these settings automatically?\n"
"Yes - Change ensure vertical shell thickness to Moderate and enable "
"alternate extra wall\n"
"No  - Don't use alternate extra wall"
msgstr ""

msgid ""
"Prime tower does not work when Adaptive Layer Height or Independent Support "
"Layer Height is on.\n"
"Which do you want to keep?\n"
"YES - Keep Prime Tower\n"
"NO  - Keep Adaptive Layer Height and Independent Support Layer Height"
msgstr ""

msgid ""
"Prime tower does not work when Adaptive Layer Height is on.\n"
"Which do you want to keep?\n"
"YES - Keep Prime Tower\n"
"NO  - Keep Adaptive Layer Height"
msgstr ""

msgid ""
"Prime tower does not work when Independent Support Layer Height is on.\n"
"Which do you want to keep?\n"
"YES - Keep Prime Tower\n"
"NO  - Keep Independent Support Layer Height"
msgstr ""

msgid ""
"seam_slope_start_height need to be smaller than layer_height.\n"
"Reset to 0."
msgstr ""

msgid ""
"Spiral mode only works when wall loops is 1, support is disabled, top shell "
"layers is 0, sparse infill density is 0 and timelapse type is traditional."
msgstr ""

msgid " But machines with I3 structure will not generate timelapse videos."
msgstr ""

msgid ""
"Change these settings automatically?\n"
"Yes - Change these settings and enable spiral mode automatically\n"
"No  - Give up using spiral mode this time"
msgstr ""
"Change these settings automatically?\n"
"Yes - Change these settings and enable spiral/vase mode automatically\n"
"No  - Cancel enabling spiral mode"

msgid "Auto bed leveling"
msgstr ""

msgid "Heatbed preheating"
msgstr ""

msgid "Sweeping XY mech mode"
msgstr ""

msgid "Changing filament"
msgstr ""

msgid "M400 pause"
msgstr ""

msgid "Paused due to filament runout"
msgstr ""

msgid "Heating hotend"
msgstr ""

msgid "Calibrating extrusion"
msgstr ""

msgid "Scanning bed surface"
msgstr ""

msgid "Inspecting first layer"
msgstr ""

msgid "Identifying build plate type"
msgstr ""

msgid "Calibrating Micro Lidar"
msgstr ""

msgid "Homing toolhead"
msgstr ""

msgid "Cleaning nozzle tip"
msgstr ""

msgid "Checking extruder temperature"
msgstr ""

msgid "Printing was paused by the user"
msgstr ""

msgid "Pause of front cover falling"
msgstr ""

msgid "Calibrating the micro lidar"
msgstr ""

msgid "Calibrating extrusion flow"
msgstr ""

msgid "Paused due to nozzle temperature malfunction"
msgstr ""

msgid "Paused due to heat bed temperature malfunction"
msgstr ""

msgid "Filament unloading"
msgstr ""

msgid "Skip step pause"
msgstr ""

msgid "Filament loading"
msgstr ""

msgid "Motor noise calibration"
msgstr ""

msgid "Paused due to AMS lost"
msgstr ""

msgid "Paused due to low speed of the heat break fan"
msgstr ""

msgid "Paused due to chamber temperature control error"
msgstr ""

msgid "Cooling chamber"
msgstr ""

msgid "Paused by the G-code inserted by user"
msgstr ""

msgid "Motor noise showoff"
msgstr ""

msgid "Nozzle filament covered detected pause"
msgstr ""

msgid "Cutter error pause"
msgstr ""

msgid "First layer error pause"
msgstr ""

msgid "Nozzle clog pause"
msgstr ""

msgid "Unknown"
msgstr ""

msgid "Fatal"
msgstr ""

msgid "Serious"
msgstr ""

msgid "Common"
msgstr ""

msgid "Update successful."
msgstr ""

msgid "Downloading failed."
msgstr ""

msgid "Verification failed."
msgstr ""

msgid "Update failed."
msgstr ""

msgid ""
"The current chamber temperature or the target chamber temperature exceeds "
"45℃. In order to avoid extruder clogging, low temperature filament (PLA/PETG/"
"TPU) is not allowed to be loaded."
msgstr ""

msgid ""
"Low temperature filament (PLA/PETG/TPU) is loaded in the extruder. In order "
"to avoid extruder clogging, it is not allowed to set the chamber temperature "
"above 45℃."
msgstr ""

msgid ""
"When you set the chamber temperature below 40℃, the chamber temperature "
"control will not be activated, and the target chamber temperature will "
"automatically be set to 0℃."
msgstr ""

msgid "Failed to start print job"
msgstr ""

msgid ""
"This calibration does not support the currently selected nozzle diameter"
msgstr ""

msgid "Current flowrate cali param is invalid"
msgstr ""

msgid "Selected diameter and machine diameter do not match"
msgstr ""

msgid "Failed to generate cali G-code"
msgstr ""

msgid "Calibration error"
msgstr ""

msgid "TPU is not supported by AMS."
msgstr ""

msgid "Bambu PET-CF/PA6-CF is not supported by AMS."
msgstr ""

msgid ""
"Damp PVA will become flexible and get stuck inside AMS, please take care to "
"dry it before use."
msgstr ""

msgid ""
"CF/GF filaments are hard and brittle, it's easy to break or get stuck in "
"AMS, please use with caution."
msgstr ""

msgid "default"
msgstr ""

#, boost-format
msgid "Edit Custom G-code (%1%)"
msgstr ""

msgid "Built-in placeholders (Double click item to add to G-code)"
msgstr ""

msgid "Search G-code placeholders"
msgstr ""

msgid "Add selected placeholder to G-code"
msgstr ""

msgid "Select placeholder"
msgstr ""

msgid "[Global] Slicing State"
msgstr ""

msgid "Read Only"
msgstr ""

msgid "Read Write"
msgstr ""

msgid "Slicing State"
msgstr ""

msgid "Print Statistics"
msgstr ""

msgid "Objects Info"
msgstr ""

msgid "Dimensions"
msgstr ""

msgid "Temperatures"
msgstr ""

msgid "Timestamps"
msgstr ""

#, boost-format
msgid "Specific for %1%"
msgstr ""

msgid "Presets"
msgstr ""

msgid "Print settings"
msgstr ""

msgid "Filament settings"
msgstr ""

msgid "SLA Materials settings"
msgstr ""

msgid "Printer settings"
msgstr ""

msgid "parameter name"
msgstr ""

#, c-format, boost-format
msgid "%s can't be a percentage"
msgstr "%s can’t be a percentage"

#, c-format, boost-format
msgid "Value %s is out of range, continue?"
msgstr ""

msgid "Parameter validation"
msgstr ""

#, c-format, boost-format
msgid "Value %s is out of range. The valid range is from %d to %d."
msgstr ""

msgid "Value is out of range."
msgstr ""

#, c-format, boost-format
msgid ""
"Is it %s%% or %s %s?\n"
"YES for %s%%, \n"
"NO for %s %s."
msgstr ""

#, boost-format
msgid ""
"Invalid input format. Expected vector of dimensions in the following format: "
"\"%1%\""
msgstr ""

msgid "Input value is out of range"
msgstr ""

msgid "Some extension in the input is invalid"
msgstr ""

#, boost-format
msgid "Invalid format. Expected vector format: \"%1%\""
msgstr ""

msgid "Layer Height"
msgstr ""

msgid "Line Width"
msgstr ""

msgid "Fan Speed"
msgstr ""

msgid "Temperature"
msgstr ""

msgid "Flow"
msgstr ""

msgid "Tool"
msgstr ""

msgid "Layer Time"
msgstr ""

msgid "Layer Time (log)"
msgstr ""

msgid "Height: "
msgstr ""

msgid "Width: "
msgstr ""

msgid "Speed: "
msgstr ""

msgid "Flow: "
msgstr ""

msgid "Layer Time: "
msgstr ""

msgid "Fan: "
msgstr ""

msgid "Temperature: "
msgstr ""

msgid "Loading G-code"
msgstr ""

msgid "Generating geometry vertex data"
msgstr ""

msgid "Generating geometry index data"
msgstr ""

msgid "Statistics of All Plates"
msgstr ""

msgid "Display"
msgstr ""

msgid "Flushed"
msgstr ""

msgid "Tower"
msgstr ""

msgid "Total"
msgstr ""

msgid "Total Estimation"
msgstr "Total estimation"

msgid "Total time"
msgstr ""

msgid "Total cost"
msgstr ""

msgid "up to"
msgstr ""

msgid "above"
msgstr ""

msgid "from"
msgstr ""

msgid "Color Scheme"
msgstr "Color scheme"

msgid "Time"
msgstr ""

msgid "Percent"
msgstr ""

msgid "Used filament"
msgstr ""

msgid "Layer Height (mm)"
msgstr "Layer height (mm)"

msgid "Line Width (mm)"
msgstr "Line width (mm)"

msgid "Speed (mm/s)"
msgstr ""

msgid "Fan Speed (%)"
msgstr "Fan speed (%)"

msgid "Temperature (°C)"
msgstr ""

msgid "Volumetric flow rate (mm³/s)"
msgstr ""

msgid "Travel"
msgstr ""

msgid "Seams"
msgstr ""

msgid "Retract"
msgstr ""

msgid "Unretract"
msgstr ""

msgid "Filament Changes"
msgstr "Filament changes"

msgid "Wipe"
msgstr ""

msgid "Options"
msgstr ""

msgid "travel"
msgstr "Travel"

msgid "Extruder"
msgstr ""

msgid "Filament change times"
msgstr ""

msgid "Cost"
msgstr ""

msgid "Color change"
msgstr ""

msgid "Print"
msgstr ""

msgid "Printer"
msgstr ""

msgid "Tool Change"
msgstr ""

msgid "Time Estimation"
msgstr ""

msgid "Normal mode"
msgstr ""

msgid "Total Filament"
msgstr ""

msgid "Model Filament"
msgstr ""

msgid "Prepare time"
msgstr ""

msgid "Model printing time"
msgstr ""

msgid "Switch to silent mode"
msgstr ""

msgid "Switch to normal mode"
msgstr ""

msgid "Variable layer height"
msgstr ""

msgid "Adaptive"
msgstr ""

msgid "Quality / Speed"
msgstr ""

msgid "Smooth"
msgstr ""

msgid "Radius"
msgstr ""

msgid "Keep min"
msgstr ""

msgid "Left mouse button:"
msgstr ""

msgid "Add detail"
msgstr ""

msgid "Right mouse button:"
msgstr ""

msgid "Remove detail"
msgstr ""

msgid "Shift + Left mouse button:"
msgstr ""

msgid "Reset to base"
msgstr ""

msgid "Shift + Right mouse button:"
msgstr ""

msgid "Smoothing"
msgstr ""

msgid "Mouse wheel:"
msgstr ""

msgid "Increase/decrease edit area"
msgstr ""

msgid "Sequence"
msgstr ""

msgid "Mirror Object"
msgstr "Mirror object"

msgid "Tool Move"
msgstr "Tool move"

msgid "Tool Rotate"
msgstr ""

msgid "Move Object"
msgstr "Move object"

msgid "Auto Orientation options"
msgstr "Auto orientation options"

msgid "Enable rotation"
msgstr ""

msgid "Optimize support interface area"
msgstr ""

msgid "Orient"
msgstr ""

msgid "Arrange options"
msgstr ""

msgid "Spacing"
msgstr ""

msgid "0 means auto spacing."
msgstr ""

msgid "Auto rotate for arrangement"
msgstr ""

msgid "Allow multiple materials on same plate"
msgstr ""

msgid "Avoid extrusion calibration region"
msgstr ""

msgid "Align to Y axis"
msgstr ""

msgid "Add plate"
msgstr ""

msgid "Auto orient all/selected objects"
msgstr ""

msgid "Auto orient all objects on current plate"
msgstr ""

msgid "Arrange all objects"
msgstr ""

msgid "Arrange objects on selected plates"
msgstr ""

msgid "Split to objects"
msgstr ""

msgid "Split to parts"
msgstr ""

msgid "Assembly View"
msgstr ""

msgid "Select Plate"
msgstr ""

msgid "Assembly Return"
msgstr ""

msgid "return"
msgstr ""

msgid "Paint Toolbar"
msgstr ""

msgid "Explosion Ratio"
msgstr ""

msgid "Section View"
msgstr ""

msgid "Assemble Control"
msgstr "Assembly Control"

msgid "Total Volume:"
msgstr ""

msgid "Assembly Info"
msgstr ""

msgid "Volume:"
msgstr ""

msgid "Size:"
msgstr ""

#, boost-format
msgid ""
"Conflicts of G-code paths have been found at layer %d, z = %.2lf mm. Please "
"separate the conflicted objects farther (%s <-> %s)."
msgstr ""

msgid "An object is laid over the plate boundaries."
msgstr ""

msgid "A G-code path goes beyond the max print height."
msgstr ""

msgid "A G-code path goes beyond the plate boundaries."
msgstr "A G-code path goes beyond plate boundaries."

msgid "Only the object being edited is visible."
msgstr ""

msgid ""
"An object is laid over the plate boundaries or exceeds the height limit.\n"
"Please solve the problem by moving it totally on or off the plate, and "
"confirming that the height is within the build volume."
msgstr ""

msgid "Calibration step selection"
msgstr ""

msgid "Micro lidar calibration"
msgstr ""

msgid "Bed leveling"
msgstr ""

msgid "Vibration compensation"
msgstr ""

msgid "Motor noise cancellation"
msgstr ""

msgid "Calibration program"
msgstr ""

msgid ""
"The calibration program detects the status of your device automatically to "
"minimize deviation.\n"
"It keeps the device performing optimally."
msgstr ""

msgid "Calibration Flow"
msgstr ""

msgid "Start Calibration"
msgstr ""

msgid "Completed"
msgstr ""

msgid "Calibrating"
msgstr ""

msgid "No step selected"
msgstr ""

msgid "Auto-record Monitoring"
msgstr ""

msgid "Go Live"
msgstr ""

msgid "Liveview Retry"
msgstr ""

msgid "Resolution"
msgstr ""

msgid "Enable"
msgstr ""

msgid "Hostname or IP"
msgstr ""

msgid "Custom camera source"
msgstr ""

msgid "Show \"Live Video\" guide page."
msgstr ""

msgid "720p"
msgstr ""

msgid "1080p"
msgstr ""

msgid "Connect Printer (LAN)"
msgstr ""

msgid "Please input the printer access code:"
msgstr ""

msgid ""
"You can find it in \"Settings > Network > Connection code\"\n"
"on the printer, as shown in the figure:"
msgstr ""
"You can find it in \"Settings > Network > Access code\"\n"
"on the printer, as shown in the figure:"

msgid "Invalid input."
msgstr "Invalid input"

msgid "New Window"
msgstr ""

msgid "Open a new window"
msgstr ""

msgid "Application is closing"
msgstr "Closing application"

msgid "Closing Application while some presets are modified."
msgstr ""

msgid "Logging"
msgstr ""

msgid "Preview"
msgstr ""

msgid "Multi-device"
msgstr ""

msgid "Project"
msgstr ""

msgid "Yes"
msgstr ""

msgid "No"
msgstr ""

msgid "will be closed before creating a new model. Do you want to continue?"
msgstr ""

msgid "Slice plate"
msgstr ""

msgid "Print plate"
msgstr ""

msgid "Slice all"
msgstr ""

msgid "Export G-code file"
msgstr ""

msgid "Export plate sliced file"
msgstr ""

msgid "Export all sliced file"
msgstr ""

msgid "Print all"
msgstr ""

msgid "Send all"
msgstr ""

msgid "Keyboard Shortcuts"
msgstr ""

msgid "Show the list of the keyboard shortcuts"
msgstr "Show the list of keyboard shortcuts"

msgid "Setup Wizard"
msgstr ""

msgid "Show Configuration Folder"
msgstr ""

msgid "Show Tip of the Day"
msgstr ""

msgid "Check for Update"
msgstr "Check for Updates"

msgid "Open Network Test"
msgstr ""

#, c-format, boost-format
msgid "&About %s"
msgstr ""

msgid "Upload Models"
msgstr ""

msgid "Download Models"
msgstr ""

msgid "Default View"
msgstr ""

#. TRN To be shown in the main menu View->Top
msgid "Top"
msgstr ""

msgid "Top View"
msgstr ""

#. TRN To be shown in the main menu View->Bottom
msgid "Bottom"
msgstr ""

msgid "Bottom View"
msgstr ""

msgid "Front"
msgstr ""

msgid "Front View"
msgstr ""

msgid "Rear"
msgstr ""

msgid "Rear View"
msgstr ""

msgid "Left"
msgstr ""

msgid "Left View"
msgstr ""

msgid "Right"
msgstr ""

msgid "Right View"
msgstr ""

msgid "Start a new window"
msgstr ""

msgid "New Project"
msgstr ""

msgid "Start a new project"
msgstr ""

msgid "Open a project file"
msgstr ""

msgid "Recent projects"
msgstr "Recent Projects"

msgid "Save Project"
msgstr ""

msgid "Save current project to file"
msgstr ""

msgid "Save Project as"
msgstr ""

msgid "Shift+"
msgstr ""

msgid "Save current project as"
msgstr ""

msgid "Import 3MF/STL/STEP/SVG/OBJ/AMF"
msgstr ""

msgid "Load a model"
msgstr ""

msgid "Import Zip Archive"
msgstr ""

msgid "Load models contained within a zip archive"
msgstr ""

msgid "Import Configs"
msgstr ""

msgid "Load configs"
msgstr ""

msgid "Import"
msgstr ""

msgid "Export all objects as one STL"
msgstr ""

msgid "Export all objects as STLs"
msgstr ""

msgid "Export Generic 3MF"
msgstr ""

msgid "Export 3mf file without using some 3mf-extensions"
msgstr ""

msgid "Export current sliced file"
msgstr ""

msgid "Export all plate sliced file"
msgstr ""

msgid "Export G-code"
msgstr ""

msgid "Export current plate as G-code"
msgstr ""

msgid "Export Preset Bundle"
msgstr ""

msgid "Export current configuration to files"
msgstr ""

msgid "Export"
msgstr ""

msgid "Quit"
msgstr ""

msgid "Undo"
msgstr ""

msgid "Redo"
msgstr ""

msgid "Cut selection to clipboard"
msgstr ""

msgid "Copy"
msgstr ""

msgid "Copy selection to clipboard"
msgstr ""

msgid "Paste"
msgstr ""

msgid "Paste clipboard"
msgstr ""

msgid "Delete selected"
msgstr "Delete Selected"

msgid "Deletes the current selection"
msgstr ""

msgid "Delete all"
msgstr "Delete All"

msgid "Deletes all objects"
msgstr ""

msgid "Clone selected"
msgstr "Clone Selected"

msgid "Clone copies of selections"
msgstr ""

msgid "Duplicate Current Plate"
msgstr ""

msgid "Duplicate the current plate"
msgstr ""

msgid "Select all"
msgstr "Select All"

msgid "Selects all objects"
msgstr ""

msgid "Deselect all"
msgstr "Deselect All"

msgid "Deselects all objects"
msgstr ""

msgid "Use Perspective View"
msgstr ""

msgid "Use Orthogonal View"
msgstr ""

msgid "Auto Perspective"
msgstr ""

msgid ""
"Automatically switch between orthographic and perspective when changing from "
"top/bottom/side views"
msgstr ""

msgid "Show &G-code Window"
msgstr ""

msgid "Show G-code window in Preview scene"
msgstr ""

msgid "Show 3D Navigator"
msgstr ""

msgid "Show 3D navigator in Prepare and Preview scene"
msgstr ""

msgid "Reset Window Layout"
msgstr ""

msgid "Reset to default window layout"
msgstr ""

msgid "Show &Labels"
msgstr ""

msgid "Show object labels in 3D scene"
msgstr ""

msgid "Show &Overhang"
msgstr ""

msgid "Show object overhang highlight in 3D scene"
msgstr ""

msgid "Show Selected Outline (beta)"
msgstr ""

msgid "Show outline around selected object in 3D scene"
msgstr ""

msgid "Preferences"
msgstr ""

msgid "Help"
msgstr ""

msgid "Temperature Calibration"
msgstr ""

msgid "Pass 1"
msgstr ""

msgid "Flow rate test - Pass 1"
msgstr ""

msgid "Pass 2"
msgstr ""

msgid "Flow rate test - Pass 2"
msgstr ""

msgid "YOLO (Recommended)"
msgstr ""

msgid "Orca YOLO flowrate calibration, 0.01 step"
msgstr ""

msgid "YOLO (perfectionist version)"
msgstr ""

msgid "Orca YOLO flowrate calibration, 0.005 step"
msgstr ""

msgid "Flow rate"
msgstr ""

msgid "Pressure advance"
msgstr ""

msgid "Retraction test"
msgstr ""

msgid "Orca Tolerance Test"
msgstr ""

msgid "Max flowrate"
msgstr ""

msgid "VFA"
msgstr ""

msgid "More..."
msgstr ""

msgid "Tutorial"
msgstr ""

msgid "Calibration help"
msgstr ""

msgid "More calibrations"
msgstr ""

msgid "&Open G-code"
msgstr ""

msgid "Open a G-code file"
msgstr ""

msgid "Re&load from Disk"
msgstr ""

msgid "Reload the plater from disk"
msgstr ""

msgid "Export &Toolpaths as OBJ"
msgstr ""

msgid "Export toolpaths as OBJ"
msgstr ""

msgid "Open &Slicer"
msgstr ""

msgid "Open Slicer"
msgstr ""

msgid "&Quit"
msgstr ""

#, c-format, boost-format
msgid "Quit %s"
msgstr ""

msgid "&File"
msgstr ""

msgid "&View"
msgstr ""

msgid "&Help"
msgstr ""

#, c-format, boost-format
msgid "A file exists with the same name: %s, do you want to overwrite it?"
msgstr "A file exists with the same name: %s. Do you want to overwrite it?"

#, c-format, boost-format
msgid "A config exists with the same name: %s, do you want to overwrite it?"
msgstr "A config exists with the same name: %s. Do you want to overwrite it?"

msgid "Overwrite file"
msgstr ""

msgid "Overwrite config"
msgstr ""

msgid "Yes to All"
msgstr ""

msgid "No to All"
msgstr ""

msgid "Choose a directory"
msgstr ""

#, c-format, boost-format
msgid "There is %d config exported. (Only non-system configs)"
msgid_plural "There are %d configs exported. (Only non-system configs)"
msgstr[0] ""
msgstr[1] ""

msgid "Export result"
msgstr "Export Result"

msgid "Select profile to load:"
msgstr ""

#, c-format, boost-format
msgid "There is %d config imported. (Only non-system and compatible configs)"
msgid_plural ""
"There are %d configs imported. (Only non-system and compatible configs)"
msgstr[0] ""
msgstr[1] ""

msgid ""
"\n"
"Hint: Make sure you have added the corresponding printer before importing "
"the configs."
msgstr ""

msgid "Import result"
msgstr ""

msgid "File is missing"
msgstr ""

msgid "The project is no longer available."
msgstr ""

msgid "Filament Settings"
msgstr "Filament settings"

msgid ""
"Do you want to synchronize your personal data from Bambu Cloud?\n"
"It contains the following information:\n"
"1. The Process presets\n"
"2. The Filament presets\n"
"3. The Printer presets"
msgstr ""
"Do you want to synchronize your personal data from Bambu Cloud?\n"
"It contains the following information:\n"
"1. Process presets\n"
"2. Filament presets\n"
"3. Printer presets"

msgid "Synchronization"
msgstr ""

msgid "The device cannot handle more conversations. Please retry later."
msgstr ""

msgid "Player is malfunctioning. Please reinstall the system player."
msgstr ""

msgid "The player is not loaded, please click \"play\" button to retry."
msgstr "The player is not loaded; please click the \"play\" button to retry."

msgid "Please confirm if the printer is connected."
msgstr ""

msgid ""
"The printer is currently busy downloading. Please try again after it "
"finishes."
msgstr ""

msgid "Printer camera is malfunctioning."
msgstr ""

msgid "A problem occurred. Please update the printer firmware and try again."
msgstr ""

msgid ""
"LAN Only Liveview is off. Please turn on the liveview on printer screen."
msgstr ""

msgid "Please enter the IP of printer to connect."
msgstr "Please enter the IP of the printer to connect."

msgid "Initializing..."
msgstr ""

msgid "Connection Failed. Please check the network and try again"
msgstr ""

msgid ""
"Please check the network and try again. You can restart or update the "
"printer if the issue persists."
msgstr ""

msgid "The printer has been logged out and cannot connect."
msgstr ""

msgid "Video Stopped."
msgstr ""

msgid "LAN Connection Failed (Failed to start liveview)"
msgstr ""

msgid ""
"Virtual Camera Tools is required for this task!\n"
"Do you want to install them?"
msgstr ""

msgid "Downloading Virtual Camera Tools"
msgstr ""

msgid ""
"Another virtual camera is running.\n"
"Orca Slicer supports only a single virtual camera.\n"
"Do you want to stop this virtual camera?"
msgstr ""

#, c-format, boost-format
msgid "Virtual camera initialize failed (%s)!"
msgstr ""

msgid "Network unreachable"
msgstr ""

msgid "Information"
msgstr ""

msgid "Playing..."
msgstr ""

msgid "Year"
msgstr ""

msgid "Month"
msgstr ""

msgid "All Files"
msgstr ""

msgid "Group files by year, recent first."
msgstr ""

msgid "Group files by month, recent first."
msgstr ""

msgid "Show all files, recent first."
msgstr ""

msgid "Switch to timelapse files."
msgstr ""

msgid "Video"
msgstr ""

msgid "Switch to video files."
msgstr ""

msgid "Switch to 3mf model files."
msgstr ""

msgid "Delete selected files from printer."
msgstr ""

msgid "Download"
msgstr ""

msgid "Download selected files from printer."
msgstr ""

msgid "Select"
msgstr ""

msgid "Batch manage files."
msgstr ""

msgid "Refresh"
msgstr ""

msgid "Reload file list from printer."
msgstr ""

msgid "No printers."
msgstr ""

msgid "Loading file list..."
msgstr ""

msgid "No files"
msgstr ""

msgid "Load failed"
msgstr ""

msgid ""
"Browsing file in SD card is not supported in current firmware. Please update "
"the printer firmware."
msgstr ""

msgid ""
"Please check if the SD card is inserted into the printer.\n"
"If it still cannot be read, you can try formatting the SD card."
msgstr ""
"Please check if the Micro SD card is inserted into the printer.\n"
"If it still cannot be read, you can try formatting the card."

msgid "LAN Connection Failed (Failed to view sdcard)"
msgstr ""

msgid "Browsing file in SD card is not supported in LAN Only Mode."
msgstr ""

#, c-format, boost-format
msgid "You are going to delete %u file from printer. Are you sure to continue?"
msgid_plural ""
"You are going to delete %u files from printer. Are you sure to continue?"
msgstr[0] ""
msgstr[1] ""

msgid "Delete files"
msgstr ""

#, c-format, boost-format
msgid "Do you want to delete the file '%s' from printer?"
msgstr ""

msgid "Delete file"
msgstr ""

msgid "Fetching model information..."
msgstr ""

msgid "Failed to fetch model information from printer."
msgstr ""

msgid "Failed to parse model information."
msgstr ""

msgid ""
"The .gcode.3mf file contains no G-code data. Please slice it with Orca "
"Slicer and export a new .gcode.3mf file."
msgstr ""

#, c-format, boost-format
msgid "File '%s' was lost! Please download it again."
msgstr ""

#, c-format, boost-format
msgid ""
"File: %s\n"
"Title: %s\n"
msgstr ""

msgid "Download waiting..."
msgstr ""

msgid "Play"
msgstr ""

msgid "Open Folder"
msgstr ""

msgid "Download finished"
msgstr ""

#, c-format, boost-format
msgid "Downloading %d%%..."
msgstr ""

msgid ""
"Reconnecting the printer, the operation cannot be completed immediately, "
"please try again later."
msgstr ""

msgid "File does not exist."
msgstr ""

msgid "File checksum error. Please retry."
msgstr ""

msgid "Not supported on the current printer version."
msgstr ""

msgid "Storage unavailable, insert SD card."
msgstr "Storage unavailable, insert Micro SD card."

#, c-format, boost-format
msgid "Error code: %d"
msgstr ""

msgid "Speed:"
msgstr ""

msgid "Deadzone:"
msgstr ""

msgid "Options:"
msgstr ""

msgid "Zoom"
msgstr ""

msgid "Translation/Zoom"
msgstr ""

msgid "3Dconnexion settings"
msgstr ""

msgid "Swap Y/Z axes"
msgstr ""

msgid "Invert X axis"
msgstr ""

msgid "Invert Y axis"
msgstr ""

msgid "Invert Z axis"
msgstr ""

msgid "Invert Yaw axis"
msgstr ""

msgid "Invert Pitch axis"
msgstr ""

msgid "Invert Roll axis"
msgstr ""

msgid "Printing Progress"
msgstr "Printing progress"

msgid "0"
msgstr ""

msgid "Layer: N/A"
msgstr ""

msgid "Clear"
msgstr ""

msgid ""
"You have completed printing the mall model, \n"
"but the synchronization of rating information has failed."
msgstr ""
"You have completed printing the mall model, \n"
"but synchronizing rating information has failed."

msgid "How do you like this printing file?"
msgstr ""

msgid ""
"(The model has already been rated. Your rating will overwrite the previous "
"rating.)"
msgstr ""

msgid "Rate"
msgstr ""

msgid "Camera"
msgstr ""

msgid "SD Card"
msgstr "MicroSD Card"

msgid "Camera Setting"
msgstr ""

msgid "Switch Camera View"
msgstr ""

msgid "Control"
msgstr ""

msgid "Printer Parts"
msgstr ""

msgid "Print Options"
msgstr ""

msgid "100%"
msgstr ""

msgid "Lamp"
msgstr ""

msgid "Aux"
msgstr ""

msgid "Cham"
msgstr ""

msgid "Bed"
msgstr ""

msgid "Debug Info"
msgstr ""

msgid "No SD Card"
msgstr "No MicroSD Card"

msgid "SD Card Abnormal"
msgstr "MicroSD Card Abnormal"

msgid "Cancel print"
msgstr ""

msgid "Are you sure you want to cancel this print?"
msgstr ""

msgid "Downloading..."
msgstr ""

msgid "Cloud Slicing..."
msgstr ""

#, c-format, boost-format
msgid "In Cloud Slicing Queue, there are %s tasks ahead."
msgstr "In Cloud Slicing Queue, there are %s tasks ahead of you."

#, c-format, boost-format
msgid "Layer: %s"
msgstr ""

#, c-format, boost-format
msgid "Layer: %d/%d"
msgstr ""

msgid ""
"Please heat the nozzle to above 170°C before loading or unloading filament."
msgstr ""

msgid "Still unload"
msgstr ""

msgid "Still load"
msgstr ""

msgid "Please select an AMS slot before calibration"
msgstr "Please select an AMS slot before calibration."

msgid ""
"Cannot read filament info: the filament is loaded to the tool head,please "
"unload the filament and try again."
msgstr ""
"Cannot read filament info: the filament is loaded to the tool head. Please "
"unload the filament and try again."

msgid "This only takes effect during printing"
msgstr ""

msgid "Silent"
msgstr ""

msgid "Standard"
msgstr ""

msgid "Sport"
msgstr ""

msgid "Ludicrous"
msgstr ""

msgid "Can't start this without SD card."
msgstr "Can't start without MicroSD card."

msgid "Rate the Print Profile"
msgstr ""

msgid "Comment"
msgstr ""

msgid "Rate this print"
msgstr ""

msgid "Add Photo"
msgstr ""

msgid "Delete Photo"
msgstr ""

msgid "Submit"
msgstr ""

msgid "Please click on the star first."
msgstr ""

msgid "Get oss config failed."
msgstr ""

msgid "Upload Pictures"
msgstr ""

msgid "Number of images successfully uploaded"
msgstr ""

msgid " upload failed"
msgstr ""

msgid " upload config prase failed\n"
msgstr ""

msgid " No corresponding storage bucket\n"
msgstr ""

msgid " cannot be opened\n"
msgstr ""

msgid ""
"The following issues occurred during the process of uploading images. Do you "
"want to ignore them?\n"
"\n"
msgstr ""

msgid "info"
msgstr ""

msgid "Synchronizing the printing results. Please retry a few seconds later."
msgstr ""

msgid "Upload failed\n"
msgstr ""

msgid "obtaining instance_id failed\n"
msgstr "Obtaining instance_id failed\n"

msgid ""
"Your comment result cannot be uploaded due to the following reasons:\n"
"\n"
"  error code: "
msgstr ""

msgid "error message: "
msgstr ""

msgid ""
"\n"
"\n"
"Would you like to redirect to the webpage to give a rating?"
msgstr ""

msgid ""
"Some of your images failed to upload. Would you like to redirect to the "
"webpage to give a rating?"
msgstr ""

msgid "You can select up to 16 images."
msgstr ""

msgid ""
"At least one successful print record of this print profile is required \n"
"to give a positive rating (4 or 5 stars)."
msgstr ""

msgid "Status"
msgstr ""

msgid "Update"
msgstr ""

msgid "Don't show again"
msgstr ""

#, c-format, boost-format
msgid "%s error"
msgstr ""

#, c-format, boost-format
msgid "%s has encountered an error"
msgstr ""

#, c-format, boost-format
msgid "%s warning"
msgstr ""

#, c-format, boost-format
msgid "%s has a warning"
msgstr ""

#, c-format, boost-format
msgid "%s info"
msgstr ""

#, c-format, boost-format
msgid "%s information"
msgstr ""

msgid "Skip"
msgstr ""

msgid "Newer 3mf version"
msgstr ""

msgid ""
"The 3mf file version is in Beta and it is newer than the current OrcaSlicer "
"version."
msgstr ""

msgid "If you would like to try Orca Slicer Beta, you may click to"
msgstr ""

msgid "Download Beta Version"
msgstr ""

msgid "The 3mf file version is newer than the current Orca Slicer version."
msgstr ""

msgid "Update your Orca Slicer could enable all functionality in the 3mf file."
msgstr ""

msgid "Current Version: "
msgstr ""

msgid "Latest Version: "
msgstr ""

msgid "Not for now"
msgstr ""

msgid "Server Exception"
msgstr ""

msgid ""
"The server is unable to respond. Please click the link below to check the "
"server status."
msgstr ""

msgid ""
"If the server is in a fault state, you can temporarily use offline printing "
"or local network printing."
msgstr ""

msgid "How to use LAN only mode"
msgstr ""

msgid "Don't show this dialog again"
msgstr ""

msgid "3D Mouse disconnected."
msgstr ""

msgid "Configuration can update now."
msgstr "A new configuration is available. Update now?"

msgid "Detail."
msgstr "More"

msgid "Integration was successful."
msgstr ""

msgid "Integration failed."
msgstr ""

msgid "Undo integration was successful."
msgstr ""

msgid "New network plug-in available."
msgstr "New network plug-in available"

msgid "Details"
msgstr ""

msgid "New printer config available."
msgstr ""

msgid "Wiki"
msgstr ""

msgid "Undo integration failed."
msgstr ""

msgid "Exporting."
msgstr "Exporting"

msgid "Software has New version."
msgstr "An update is available!"

msgid "Goto download page."
msgstr "Go to download page"

msgid "Open Folder."
msgstr ""

msgid "Safely remove hardware."
msgstr ""

#, c-format, boost-format
msgid "%1$d Object has custom supports."
msgid_plural "%1$d Objects have custom supports."
msgstr[0] ""
msgstr[1] ""

#, c-format, boost-format
msgid "%1$d Object has color painting."
msgid_plural "%1$d Objects have color painting."
msgstr[0] ""
msgstr[1] ""

#, c-format, boost-format
msgid "%1$d object was loaded as a part of cut object."
msgid_plural "%1$d objects were loaded as parts of cut object"
msgstr[0] ""
msgstr[1] ""

msgid "ERROR"
msgstr ""

msgid "COMPLETED"
msgstr ""

msgid "CANCELED"
msgstr ""

msgid "Cancel upload"
msgstr ""

msgid "Jump to"
msgstr ""

msgid "Error:"
msgstr ""

msgid "Warning:"
msgstr ""

msgid "Exported successfully"
msgstr ""

msgid "Model file downloaded."
msgstr ""

msgid "Serious warning:"
msgstr ""

msgid " (Repair)"
msgstr ""

msgid " Click here to install it."
msgstr ""

msgid "WARNING:"
msgstr ""

msgid "Your model needs support! Please enable support material."
msgstr ""

msgid "G-code path overlap"
msgstr ""

msgid "Support painting"
msgstr "Support Painting"

msgid "Color painting"
msgstr "Color Painting"

msgid "Cut connectors"
msgstr ""

msgid "Layers"
msgstr ""

msgid "Range"
msgstr ""

msgid ""
"The application cannot run normally because OpenGL version is lower than "
"2.0.\n"
msgstr ""
"The application cannot run normally because your OpenGL version is lower "
"than 2.0.\n"

msgid "Please upgrade your graphics card driver."
msgstr ""

msgid "Unsupported OpenGL version"
msgstr ""

#, c-format, boost-format
msgid ""
"Unable to load shaders:\n"
"%s"
msgstr ""

msgid "Error loading shaders"
msgstr ""

msgctxt "Layers"
msgid "Top"
msgstr ""

msgctxt "Layers"
msgid "Bottom"
msgstr ""

msgid "Enable AI monitoring of printing"
msgstr ""

msgid "Sensitivity of pausing is"
msgstr ""

msgid "Enable detection of build plate position"
msgstr ""

msgid ""
"The localization tag of build plate is detected, and printing is paused if "
"the tag is not in predefined range."
msgstr ""
"The localization tag of the build plate will be detected, and printing will "
"be paused if the tag is not in predefined range."

msgid "First Layer Inspection"
msgstr ""

msgid "Auto-recovery from step loss"
msgstr "Auto-recover from step loss"

msgid "Allow Prompt Sound"
msgstr ""

msgid "Filament Tangle Detect"
msgstr "Filament Tangle Detection"

msgid "Nozzle Clumping Detection"
msgstr ""

msgid "Check if the nozzle is clumping by filament or other foreign objects."
msgstr ""

msgid "Nozzle Type"
msgstr ""

msgid "Stainless Steel"
msgstr ""

msgid "Hardened Steel"
msgstr ""

#, c-format, boost-format
msgid "%.1f"
msgstr ""

msgid "Global"
msgstr ""

msgid "Objects"
msgstr ""

msgid "Advance"
msgstr "Advanced"

msgid "Compare presets"
msgstr ""

msgid "View all object's settings"
msgstr ""

msgid "Material settings"
msgstr ""

msgid "Remove current plate (if not last one)"
msgstr ""

msgid "Auto orient objects on current plate"
msgstr ""

msgid "Arrange objects on current plate"
msgstr ""

msgid "Unlock current plate"
msgstr ""

msgid "Lock current plate"
msgstr ""

msgid "Edit current plate name"
msgstr ""

msgid "Move plate to the front"
msgstr ""

msgid "Customize current plate"
msgstr ""

#, boost-format
msgid " plate %1%:"
msgstr ""

msgid "Invalid name, the following characters are not allowed:"
msgstr ""

msgid "Sliced Info"
msgstr ""

msgid "Used Filament (m)"
msgstr ""

msgid "Used Filament (mm³)"
msgstr ""

msgid "Used Filament (g)"
msgstr ""

msgid "Used Materials"
msgstr ""

msgid "Estimated time"
msgstr ""

msgid "Filament changes"
msgstr ""

msgid "Click to edit preset"
msgstr ""

msgid "Connection"
msgstr ""

msgid "Bed type"
msgstr ""

msgid "Flushing volumes"
msgstr ""

msgid "Add one filament"
msgstr ""

msgid "Remove last filament"
msgstr ""

msgid "Synchronize filament list from AMS"
msgstr ""

msgid "Set filaments to use"
msgstr ""

msgid "Search plate, object and part."
msgstr ""

msgid "Pellets"
msgstr ""

msgid ""
"No AMS filaments. Please select a printer in 'Device' page to load AMS info."
msgstr ""

msgid "Sync filaments with AMS"
msgstr ""

msgid ""
"Sync filaments with AMS will drop all current selected filament presets and "
"colors. Do you want to continue?"
msgstr ""

msgid ""
"Already did a synchronization, do you want to sync only changes or resync "
"all?"
msgstr ""
"Already did a synchronization; do you want to sync only changes or resync "
"all?"

msgid "Sync"
msgstr ""

msgid "Resync"
msgstr ""

msgid "There are no compatible filaments, and sync is not performed."
msgstr ""

msgid ""
"There are some unknown filaments mapped to generic preset. Please update "
"Orca Slicer or restart Orca Slicer to check if there is an update to system "
"presets."
msgstr ""

#, boost-format
msgid "Do you want to save changes to \"%1%\"?"
msgstr ""

#, c-format, boost-format
msgid ""
"Successfully unmounted. The device %s (%s) can now be safely removed from the "
"computer."
msgstr ""

#, c-format, boost-format
msgid "Ejecting of device %s (%s) has failed."
msgstr ""

msgid "Previous unsaved project detected, do you want to restore it?"
msgstr ""
"Previously unsaved items have been detected. Do you want to restore them?"

msgid "Restore"
msgstr ""

msgid ""
"The current hot bed temperature is relatively high. The nozzle may be "
"clogged when printing this filament in a closed enclosure. Please open the "
"front door and/or remove the upper glass."
msgstr ""
"The current heatbed temperature is relatively high. The nozzle may clog when "
"printing this filament in a closed environment. Please open the front door "
"and/or remove the upper glass."

msgid ""
"The nozzle hardness required by the filament is higher than the default "
"nozzle hardness of the printer. Please replace the hardened nozzle or "
"filament, otherwise, the nozzle will be attrited or damaged."
msgstr ""
"The nozzle hardness required by the filament is higher than the default "
"nozzle hardness of the printer. Please replace the hardened nozzle or "
"filament, otherwise, the nozzle will be worn down or damaged."

msgid ""
"Enabling traditional timelapse photography may cause surface imperfections. "
"It is recommended to change to smooth mode."
msgstr ""

msgid "Expand sidebar"
msgstr ""

msgid "Collapse sidebar"
msgstr ""

#, c-format, boost-format
msgid "Loading file: %s"
msgstr ""

msgid "The 3mf is not supported by OrcaSlicer, load geometry data only."
msgstr "The 3mf is not supported by OrcaSlicer, loading geometry data only."

msgid "Load 3mf"
msgstr ""

#, c-format, boost-format
msgid ""
"The 3mf's version %s is newer than %s's version %s, found following "
"unrecognized keys:"
msgstr ""

msgid "You'd better upgrade your software.\n"
msgstr "You should update your software.\n"

#, c-format, boost-format
msgid ""
"The 3mf's version %s is newer than %s's version %s, Suggest to upgrade your "
"software."
msgstr ""

msgid "Invalid values found in the 3mf:"
msgstr ""

msgid "Please correct them in the param tabs"
msgstr "Please correct them in the Param tabs"

msgid ""
"The 3mf has the following modified G-code in filament or printer presets:"
msgstr ""

msgid ""
"Please confirm that all modified G-code is safe to prevent any damage to the "
"machine!"
msgstr ""

msgid "Modified G-code"
msgstr ""

msgid "The 3mf has the following customized filament or printer presets:"
msgstr ""

msgid ""
"Please confirm that the G-code within these presets is safe to prevent any "
"damage to the machine!"
msgstr ""

msgid "Customized Preset"
msgstr ""

msgid "Name of components inside step file is not UTF8 format!"
msgstr "Component name(s) inside step file not in UTF8 format!"

msgid "The name may show garbage characters!"
msgstr "Because of unsupported text encoding, garbage characters may appear!"

msgid "Remember my choice."
msgstr ""

#, boost-format
msgid "Failed loading file \"%1%\". An invalid configuration was found."
msgstr ""

msgid "Objects with zero volume removed"
msgstr ""

msgid "The volume of the object is zero"
msgstr ""

#, c-format, boost-format
msgid ""
"The object from file %s is too small, and maybe in meters or inches.\n"
" Do you want to scale to millimeters?"
msgstr ""
"The object from file %s is too small, and may be in meters or inches.\n"
" Do you want to scale to millimeters?"

msgid "Object too small"
msgstr ""

msgid ""
"This file contains several objects positioned at multiple heights.\n"
"Instead of considering them as multiple objects, should \n"
"the file be loaded as a single object having multiple parts?"
msgstr ""
"This file contains several objects positioned at multiple heights.\n"
"Instead of considering them as multiple objects, should \n"
"the file be loaded as a single object with multiple parts?"

msgid "Multi-part object detected"
msgstr ""

msgid "Load these files as a single object with multiple parts?\n"
msgstr ""

msgid "Object with multiple parts was detected"
msgstr "An object with multiple parts was detected"

msgid "The file does not contain any geometry data."
msgstr ""

msgid ""
"Your object appears to be too large, do you want to scale it down to fit the "
"print bed automatically?"
msgstr ""

msgid "Object too large"
msgstr ""

msgid "Export STL file:"
msgstr ""

msgid "Export AMF file:"
msgstr ""

msgid "Save file as:"
msgstr "Save file as"

msgid "Export OBJ file:"
msgstr ""

#, c-format, boost-format
msgid ""
"The file %s already exists\n"
"Do you want to replace it?"
msgstr ""
"The file %s already exists.\n"
"Do you want to replace it?"

msgid "Confirm Save As"
msgstr ""

msgid "Delete object which is a part of cut object"
msgstr ""

msgid ""
"You try to delete an object which is a part of a cut object.\n"
"This action will break a cut correspondence.\n"
"After that model consistency can't be guaranteed."
msgstr ""
"You are trying to delete an object which is a part of a cut object.\n"
"This action will break a cut correspondence.\n"
"After that, model consistency can't be guaranteed."

msgid "The selected object couldn't be split."
msgstr ""

msgid "Another export job is running."
msgstr ""

msgid "Unable to replace with more than one volume"
msgstr ""

msgid "Error during replace"
msgstr "Error during replacement"

msgid "Replace from:"
msgstr ""

msgid "Select a new file"
msgstr ""

msgid "File for the replace wasn't selected"
msgstr "File for the replacement wasn't selected"

msgid "Please select a file"
msgstr ""

msgid "Do you want to replace it"
msgstr "Do you want to replace it?"

msgid "Message"
msgstr ""

msgid "Reload from:"
msgstr ""

msgid "Unable to reload:"
msgstr ""

msgid "Error during reload"
msgstr ""

msgid "There are warnings after slicing models:"
msgstr ""

msgid "warnings"
msgstr ""

msgid "Invalid data"
msgstr ""

msgid "Slicing Canceled"
msgstr ""

#, c-format, boost-format
msgid "Slicing Plate %d"
msgstr ""

msgid "Please resolve the slicing errors and publish again."
msgstr ""

msgid ""
"Network Plug-in is not detected. Network related features are unavailable."
msgstr ""

msgid ""
"Preview only mode:\n"
"The loaded file contains G-code only, cannot enter the Prepare page."
msgstr ""

msgid "You can keep the modified presets to the new project or discard them"
msgstr "You can keep the modified presets for the new project or discard them"

msgid "Creating a new project"
msgstr ""

msgid "Load project"
msgstr ""

msgid ""
"Failed to save the project.\n"
"Please check whether the folder exists online or if other programs open the "
"project file."
msgstr ""
"Failed to save the project.\n"
"Please check whether the folder exists online or if other programs have the "
"project file open."

msgid "Save project"
msgstr ""

msgid "Importing Model"
msgstr ""

msgid "prepare 3mf file..."
msgstr "preparing 3mf file..."

msgid "Download failed, unknown file format."
msgstr "Download failed; unknown file format."

msgid "downloading project..."
msgstr ""

msgid "Download failed, File size exception."
msgstr "Download failed; File size exception."

#, c-format, boost-format
msgid "Project downloaded %d%%"
msgstr ""

msgid ""
"Importing to Orca Slicer failed. Please download the file and manually "
"import it."
msgstr ""

msgid "INFO:"
msgstr ""

msgid ""
"No accelerations provided for calibration. Use default acceleration value "
msgstr ""

msgid "mm/s²"
msgstr ""

msgid "No speeds provided for calibration. Use default optimal speed "
msgstr ""

msgid "mm/s"
msgstr ""

msgid "Import SLA archive"
msgstr ""

msgid "The selected file"
msgstr ""

msgid "does not contain valid G-code."
msgstr "Does not contain valid G-code."

msgid "Error occurs while loading G-code file"
msgstr "An Error has occurred while loading the G-code file."

#. TRN %1% is archive path
#, boost-format
msgid "Loading of a ZIP archive on path %1% has failed."
msgstr ""

#. TRN: First argument = path to file, second argument = error description
#, boost-format
msgid "Failed to unzip file to %1%: %2%"
msgstr ""

#, boost-format
msgid "Failed to find unzipped file at %1%. Unzipping of file has failed."
msgstr ""

msgid "Drop project file"
msgstr ""

msgid "Please select an action"
msgstr ""

msgid "Open as project"
msgstr ""

msgid "Import geometry only"
msgstr ""

msgid ""
"This option can be changed later in preferences, under 'Load Behaviour'."
msgstr ""

msgid "Only one G-code file can be opened at the same time."
msgstr "Only one G-code file can be opened at a time."

msgid "G-code loading"
msgstr ""

msgid "G-code files cannot be loaded with models together!"
msgstr "G-code files and models cannot be loaded together!"

msgid "Cannot add models when in preview mode!"
msgstr "Unable to add models in preview mode"

msgid "All objects will be removed, continue?"
msgstr ""

msgid "The current project has unsaved changes, save it before continue?"
msgstr ""
"The current project has unsaved changes. Would you like to save before "
"continuing?"

msgid "Number of copies:"
msgstr ""

msgid "Copies of the selected object"
msgstr ""

msgid "Save G-code file as:"
msgstr ""

msgid "Save SLA file as:"
msgstr ""

msgid "The provided file name is not valid."
msgstr ""

msgid "The following characters are not allowed by a FAT file system:"
msgstr ""

msgid "Save Sliced file as:"
msgstr ""

#, c-format, boost-format
msgid ""
"The file %s has been sent to the printer's storage space and can be viewed "
"on the printer."
msgstr ""

msgid ""
"Unable to perform boolean operation on model meshes. Only positive parts "
"will be kept. You may fix the meshes and try again."
msgstr ""

#, boost-format
msgid "Reason: part \"%1%\" is empty."
msgstr ""

#, boost-format
msgid "Reason: part \"%1%\" does not bound a volume."
msgstr ""

#, boost-format
msgid "Reason: part \"%1%\" has self intersection."
msgstr ""

#, boost-format
msgid "Reason: \"%1%\" and another part have no intersection."
msgstr ""

msgid ""
"Unable to perform boolean operation on model meshes. Only positive parts "
"will be exported."
msgstr ""

msgid ""
"Are you sure you want to store original SVGs with their local paths into the "
"3MF file?\n"
"If you hit 'NO', all SVGs in the project will not be editable any more."
msgstr ""

msgid "Private protection"
msgstr ""

msgid "Is the printer ready? Is the print sheet in place, empty and clean?"
msgstr ""

msgid "Upload and Print"
msgstr ""

msgid ""
"Print By Object: \n"
"Suggest to use auto-arrange to avoid collisions when printing."
msgstr ""
"Print By Object: \n"
"We suggest using auto-arrange to avoid collisions when printing."

msgid "Send G-code"
msgstr ""

msgid "Send to printer"
msgstr ""

msgid "Custom supports and color painting were removed before repairing."
msgstr ""

msgid "Optimize Rotation"
msgstr ""

msgid "Invalid number"
msgstr ""

msgid "Plate Settings"
msgstr ""

#, boost-format
msgid "Number of currently selected parts: %1%\n"
msgstr ""

#, boost-format
msgid "Number of currently selected objects: %1%\n"
msgstr ""

#, boost-format
msgid "Part name: %1%\n"
msgstr ""

#, boost-format
msgid "Object name: %1%\n"
msgstr ""

#, boost-format
msgid "Size: %1% x %2% x %3% in\n"
msgstr ""

#, boost-format
msgid "Size: %1% x %2% x %3% mm\n"
msgstr ""

#, boost-format
msgid "Volume: %1% in³\n"
msgstr ""

#, boost-format
msgid "Volume: %1% mm³\n"
msgstr ""

#, boost-format
msgid "Triangles: %1%\n"
msgstr ""

msgid "Tips:"
msgstr ""

msgid ""
"\"Fix Model\" feature is currently only on Windows. Please repair the model "
"on Orca Slicer(windows) or CAD softwares."
msgstr ""

#, c-format, boost-format
msgid ""
"Plate %d: %s is not suggested to be used to print filament %s (%s). If you "
"still want to do this print job, please set this filament's bed temperature "
"to non-zero."
msgstr ""
"Plate %d: %s is not suggested for use printing filament %s (%s). If you "
"still want to do this print job, please set this filament's bed temperature "
"to a number that is not zero."

msgid "Switching the language requires application restart.\n"
msgstr "Switching languages requires the application to restart.\n"

msgid "Do you want to continue?"
msgstr ""

msgid "Language selection"
msgstr ""

msgid "Switching application language while some presets are modified."
msgstr ""

msgid "Changing application language"
msgstr ""

msgid "Changing the region will log out your account.\n"
msgstr "Changing the region will log you out of your account.\n"

msgid "Region selection"
msgstr ""

msgid "Second"
msgstr ""

msgid "Browse"
msgstr ""

msgid "Choose Download Directory"
msgstr ""

msgid "Associate"
msgstr ""

msgid "with OrcaSlicer so that Orca can open models from"
msgstr ""

msgid "Current Association: "
msgstr ""

msgid "Current Instance"
msgstr ""

msgid "Current Instance Path: "
msgstr ""

msgid "General Settings"
msgstr ""

msgid "Asia-Pacific"
msgstr ""

msgid "China"
msgstr ""

msgid "Europe"
msgstr ""

msgid "North America"
msgstr ""

msgid "Others"
msgstr ""

msgid "Login Region"
msgstr ""

msgid "Stealth Mode"
msgstr ""

msgid ""
"This stops the transmission of data to Bambu's cloud services. Users who "
"don't use BBL machines or use LAN mode only can safely turn on this function."
msgstr ""

msgid "Enable network plugin"
msgstr ""

msgid "Check for stable updates only"
msgstr ""

msgid "Metric"
msgstr ""

msgid "Imperial"
msgstr ""

msgid "Units"
msgstr ""

msgid "Allow only one OrcaSlicer instance"
msgstr ""

msgid ""
"On OSX there is always only one instance of app running by default. However "
"it is allowed to run multiple instances of same app from the command line. "
"In such case this settings will allow only one instance."
msgstr ""

msgid ""
"If this is enabled, when starting OrcaSlicer and another instance of the "
"same OrcaSlicer is already running, that instance will be reactivated "
"instead."
msgstr ""

msgid "Home"
msgstr ""

msgid "Default Page"
msgstr ""

msgid "Set the page opened on startup."
msgstr ""

msgid "Touchpad"
msgstr ""

msgid "Camera style"
msgstr ""

msgid ""
"Select camera navigation style.\n"
"Default: LMB+move for rotation, RMB/MMB+move for panning.\n"
"Touchpad: Alt+move for rotation, Shift+move for panning."
msgstr ""

msgid "Zoom to mouse position"
msgstr ""

msgid ""
"Zoom in towards the mouse pointer's position in the 3D view, rather than the "
"2D window center."
msgstr ""

msgid "Use free camera"
msgstr ""

msgid "If enabled, use free camera. If not enabled, use constrained camera."
msgstr ""

msgid "Reverse mouse zoom"
msgstr ""

msgid "If enabled, reverses the direction of zoom with mouse wheel."
msgstr ""

msgid "Show splash screen"
msgstr ""

msgid "Show the splash screen during startup."
msgstr ""

msgid "Show \"Tip of the day\" notification after start"
msgstr ""

msgid "If enabled, useful hints are displayed at startup."
msgstr ""

msgid "Flushing volumes: Auto-calculate every time the color changed."
msgstr ""

msgid "If enabled, auto-calculate every time the color changed."
msgstr "If enabled, auto-calculate every time the color changes."

msgid ""
"Flushing volumes: Auto-calculate every time when the filament is changed."
msgstr "Flushing volumes: Auto-calculate every time the filament is changed."

msgid "If enabled, auto-calculate every time when filament is changed"
msgstr "If enabled, auto-calculate every time filament is changed"

msgid "Remember printer configuration"
msgstr ""

msgid ""
"If enabled, Orca will remember and switch filament/process configuration for "
"each printer automatically."
msgstr ""

msgid "Multi-device Management (Take effect after restarting Orca Slicer)."
msgstr ""

msgid ""
"With this option enabled, you can send a task to multiple devices at the "
"same time and manage multiple devices."
msgstr ""

msgid "Auto arrange plate after cloning"
msgstr ""

msgid "Auto arrange plate after object cloning"
msgstr ""

msgid "Network"
msgstr ""

msgid "Auto sync user presets (Printer/Filament/Process)"
msgstr ""

msgid "User Sync"
msgstr ""

msgid "Update built-in Presets automatically."
msgstr "Update built-in presets automatically."

msgid "System Sync"
msgstr ""

msgid "Clear my choice on the unsaved presets."
msgstr ""

msgid "Associate files to OrcaSlicer"
msgstr "Associate files to Orca Slicer"

msgid "Associate .3mf files to OrcaSlicer"
msgstr "Associate .3mf files to Orca Slicer"

msgid "If enabled, sets OrcaSlicer as default application to open .3mf files"
msgstr ""
"If enabled, this sets Orca Slicer as the default application to open .3mf "
"files."

msgid "Associate .stl files to OrcaSlicer"
msgstr "Associate .stl files to Orca Slicer"

msgid "If enabled, sets OrcaSlicer as default application to open .stl files"
msgstr ""
"If enabled, this sets Orca Slicer as the default application to open .stl "
"files."

msgid "Associate .step/.stp files to OrcaSlicer"
msgstr "Associate .step/.stp files to Orca Slicer"

msgid "If enabled, sets OrcaSlicer as default application to open .step files"
msgstr ""
"If enabled, this sets Orca Slicer as the default application to open .step "
"files."

msgid "Associate web links to OrcaSlicer"
msgstr ""

msgid "Associate URLs to OrcaSlicer"
msgstr ""

msgid "Load All"
msgstr ""

msgid "Ask When Relevant"
msgstr ""

msgid "Always Ask"
msgstr ""

msgid "Load Geometry Only"
msgstr ""

msgid "Load Behaviour"
msgstr ""

msgid "Should printer/filament/process settings be loaded when opening a .3mf?"
msgstr ""

msgid "Maximum recent projects"
msgstr ""

msgid "Maximum count of recent projects"
msgstr ""

msgid "Clear my choice on the unsaved projects."
msgstr ""

msgid "No warnings when loading 3MF with modified G-code"
msgstr ""

msgid "Auto-Backup"
msgstr ""

msgid ""
"Backup your project periodically for restoring from the occasional crash."
msgstr ""
"Backup your project periodically to help with restoring from an occasional "
"crash."

msgid "every"
msgstr ""

msgid "The period of backup in seconds."
msgstr ""

msgid "Downloads"
msgstr ""

msgid "Dark Mode"
msgstr ""

msgid "Enable Dark mode"
msgstr "Enable Dark Mode"

msgid "Develop mode"
msgstr "Developer mode"

msgid "Skip AMS blacklist check"
msgstr ""

msgid "Home page and daily tips"
msgstr ""

msgid "Show home page on startup"
msgstr ""

msgid "Sync settings"
msgstr ""

msgid "User sync"
msgstr ""

msgid "Preset sync"
msgstr ""

msgid "Preferences sync"
msgstr ""

msgid "View control settings"
msgstr ""

msgid "Rotate of view"
msgstr "Rotate View"

msgid "Move of view"
msgstr "Pan View"

msgid "Zoom of view"
msgstr "Zoom View"

msgid "Other"
msgstr ""

msgid "Mouse wheel reverses when zooming"
msgstr "Reverse scroll direction while zooming"

msgid "Enable SSL(MQTT)"
msgstr ""

msgid "Enable SSL(FTP)"
msgstr ""

msgid "Internal developer mode"
msgstr ""

msgid "Log Level"
msgstr ""

msgid "fatal"
msgstr ""

msgid "error"
msgstr ""

msgid "warning"
msgstr ""

msgid "debug"
msgstr ""

msgid "trace"
msgstr ""

msgid "Host Setting"
msgstr ""

msgid "DEV host: api-dev.bambu-lab.com/v1"
msgstr ""

msgid "QA  host: api-qa.bambu-lab.com/v1"
msgstr ""

msgid "PRE host: api-pre.bambu-lab.com/v1"
msgstr ""

msgid "Product host"
msgstr ""

msgid "debug save button"
msgstr "Debug save button"

msgid "save debug settings"
msgstr ""

msgid "DEBUG settings have been saved successfully!"
msgstr "Debug settings have been saved successfully!"

msgid "Cloud environment switched, please login again!"
msgstr "Cloud environment switched; please login again!"

msgid "System presets"
msgstr ""

msgid "User presets"
msgstr ""

msgid "Incompatible presets"
msgstr ""

msgid "AMS filaments"
msgstr "AMS filament"

msgid "Click to select filament color"
msgstr ""

msgid "Please choose the filament color"
msgstr ""

msgid "Add/Remove presets"
msgstr ""

msgid "Edit preset"
msgstr ""

msgid "Project-inside presets"
msgstr ""

msgid "Add/Remove filaments"
msgstr "Add/Remove filament"

msgid "Add/Remove materials"
msgstr ""

msgid "Select/Remove printers (system presets)"
msgstr ""

msgid "Create printer"
msgstr ""

msgid "The selected preset is null!"
msgstr ""

msgid "End"
msgstr ""

msgid "Customize"
msgstr ""

msgid "Other layer filament sequence"
msgstr ""

msgid "Please input layer value (>= 2)."
msgstr ""

msgid "Plate name"
msgstr ""

msgid "Same as Global Print Sequence"
msgstr ""

msgid "Print sequence"
msgstr ""

msgid "Same as Global"
msgstr ""

msgid "Disable"
msgstr ""

msgid "Spiral vase"
msgstr ""

msgid "First layer filament sequence"
msgstr ""

msgid "Same as Global Plate Type"
msgstr ""

msgid "Same as Global Bed Type"
msgstr "Same as Global Plate Type"

msgid "By Layer"
msgstr ""

msgid "By Object"
msgstr ""

msgid "Accept"
msgstr ""

msgid "Log Out"
msgstr ""

msgid "Slice all plate to obtain time and filament estimation"
msgstr "Slice all plates to obtain time and filament estimation"

msgid "Packing project data into 3mf file"
msgstr ""

msgid "Uploading 3mf"
msgstr ""

msgid "Jump to model publish web page"
msgstr ""

msgid "Note: The preparation may take several minutes. Please be patient."
msgstr ""

msgid "Publish"
msgstr ""

msgid "Publish was canceled"
msgstr ""

msgid "Slicing Plate 1"
msgstr ""

msgid "Packing data to 3mf"
msgstr ""

msgid "Jump to webpage"
msgstr ""

#, c-format, boost-format
msgid "Save %s as"
msgstr ""

msgid "User Preset"
msgstr ""

msgid "Preset Inside Project"
msgstr ""

msgid "Name is unavailable."
msgstr ""

msgid "Overwriting a system profile is not allowed."
msgstr ""

#, boost-format
msgid "Preset \"%1%\" already exists."
msgstr ""

#, boost-format
msgid ""
"Preset \"%1%\" already exists and is incompatible with the current printer."
msgstr ""

msgid "Please note that saving will overwrite this preset."
msgstr "Please note that saving will overwrite the current preset."

msgid "The name cannot be the same as a preset alias name."
msgstr ""

msgid "Save preset"
msgstr ""

msgctxt "PresetName"
msgid "Copy"
msgstr ""

#, boost-format
msgid "Printer \"%1%\" is selected with preset \"%2%\""
msgstr ""

#, boost-format
msgid "Please choose an action with \"%1%\" preset after saving."
msgstr ""

#, boost-format
msgid "For \"%1%\", change \"%2%\" to \"%3%\" "
msgstr ""

#, boost-format
msgid "For \"%1%\", add \"%2%\" as a new preset"
msgstr ""

#, boost-format
msgid "Simply switch to \"%1%\""
msgstr ""

msgid "Task canceled"
msgstr ""

msgid "(LAN)"
msgstr ""

msgid "Search"
msgstr ""

msgid "My Device"
msgstr ""

msgid "Other Device"
msgstr ""

msgid "Online"
msgstr ""

msgid "Input access code"
msgstr ""

msgid "Can't find my devices?"
msgstr "Can't find devices?"

msgid "Log out successful."
msgstr ""

msgid "Busy"
msgstr ""

msgid "Bambu Cool Plate"
msgstr ""

msgid "PLA Plate"
msgstr ""

msgid "Bambu Engineering Plate"
msgstr ""

msgid "Bambu Smooth PEI Plate"
msgstr ""

msgid "High temperature Plate"
msgstr ""

msgid "Bambu Textured PEI Plate"
msgstr ""

msgid "Send print job to"
msgstr ""

msgid "Flow Dynamics Calibration"
msgstr ""

msgid "Click here if you can't connect to the printer"
msgstr ""

msgid "send completed"
msgstr "Send complete"

msgid "Error code"
msgstr ""

msgid "No login account, only printers in LAN mode are displayed"
msgstr ""

msgid "Connecting to server"
msgstr ""

msgid "Synchronizing device information"
msgstr ""

msgid "Synchronizing device information time out"
msgstr "Synchronizing device information timed out"

msgid "Cannot send the print job when the printer is updating firmware"
msgstr "Cannot send a print job while the printer is updating firmware"

msgid ""
"The printer is executing instructions. Please restart printing after it ends"
msgstr ""

msgid "The printer is busy on other print job"
msgstr "The printer is busy with another print job."

#, c-format, boost-format
msgid ""
"Filament %s exceeds the number of AMS slots. Please update the printer "
"firmware to support AMS slot assignment."
msgstr ""

msgid ""
"Filament exceeds the number of AMS slots. Please update the printer firmware "
"to support AMS slot assignment."
msgstr ""

msgid ""
"Filaments to AMS slots mappings have been established. You can click a "
"filament above to change its mapping AMS slot"
msgstr ""

msgid ""
"Please click each filament above to specify its mapping AMS slot before "
"sending the print job"
msgstr ""

#, c-format, boost-format
msgid ""
"Filament %s does not match the filament in AMS slot %s. Please update the "
"printer firmware to support AMS slot assignment."
msgstr ""

msgid ""
"Filament does not match the filament in AMS slot. Please update the printer "
"firmware to support AMS slot assignment."
msgstr ""

msgid ""
"The printer firmware only supports sequential mapping of filament => AMS "
"slot."
msgstr ""

msgid "An SD card needs to be inserted before printing."
msgstr "A MicroSD card needs to be inserted before printing."

#, c-format, boost-format
msgid ""
"The selected printer (%s) is incompatible with the chosen printer profile in "
"the slicer (%s)."
msgstr ""

msgid "An SD card needs to be inserted to record timelapse."
msgstr "A MicroSD card needs to be inserted to record a timelapse."

msgid ""
"Cannot send the print job to a printer whose firmware is required to get "
"updated."
msgstr "Cannot send the print job to a printer whose firmware must be updated."

msgid "Cannot send the print job for empty plate"
msgstr "Cannot send a print job for an empty plate."

msgid "This printer does not support printing all plates"
msgstr ""

msgid ""
"When enable spiral vase mode, machines with I3 structure will not generate "
"timelapse videos."
msgstr ""
"When spiral vase mode is enabled, machines with I3 structure will not "
"generate timelapse videos."

msgid ""
"Timelapse is not supported because Print sequence is set to \"By object\"."
msgstr ""

msgid "Errors"
msgstr ""

msgid "Please check the following:"
msgstr ""

msgid ""
"The printer type selected when generating G-code is not consistent with the "
"currently selected printer. It is recommended that you use the same printer "
"type for slicing."
msgstr ""

msgid ""
"There are some unknown filaments in the AMS mappings. Please check whether "
"they are the required filaments. If they are okay, press \"Confirm\" to "
"start printing."
msgstr ""
"There are some unknown filaments in the AMS mappings. Please check whether "
"they are the required filaments. If they are okay, click \"Confirm\" to "
"start printing."

#, c-format, boost-format
msgid "nozzle in preset: %s %s"
msgstr ""

#, c-format, boost-format
msgid "nozzle memorized: %.2f %s"
msgstr ""

msgid ""
"Your nozzle diameter in sliced file is not consistent with memorized nozzle. "
"If you changed your nozzle lately, please go to Device > Printer Parts to "
"change settings."
msgstr ""
"Your nozzle diameter in sliced file is not consistent with the saved nozzle. "
"If you changed your nozzle lately, please go to Device > Printer Parts to "
"change settings."

#, c-format, boost-format
msgid ""
"Printing high temperature material (%s material) with %s may cause nozzle "
"damage"
msgstr ""

msgid "Please fix the error above, otherwise printing cannot continue."
msgstr ""

msgid ""
"Please click the confirm button if you still want to proceed with printing."
msgstr ""

msgid ""
"Connecting to the printer. Unable to cancel during the connection process."
msgstr ""

msgid ""
"Caution to use! Flow calibration on Textured PEI Plate may fail due to the "
"scattered surface."
msgstr ""

msgid "Automatic flow calibration using Micro Lidar"
msgstr ""

msgid "Modifying the device name"
msgstr ""

msgid "Bind with Pin Code"
msgstr ""

msgid "Bind with Access Code"
msgstr ""

msgid "Send to Printer SD card"
msgstr "Send to Printer MicroSD card"

msgid "Cannot send the print task when the upgrade is in progress"
msgstr "Cannot send print tasks when an update is in progress"

msgid "The selected printer is incompatible with the chosen printer presets."
msgstr ""

msgid "An SD card needs to be inserted before send to printer SD card."
msgstr ""
"A MicroSD card needs to be inserted before sending to the printer SD card."

msgid "The printer is required to be in the same LAN as Orca Slicer."
msgstr "The printer is required to be on the same LAN as Orca Slicer."

msgid "The printer does not support sending to printer SD card."
msgstr "The printer does not support sending to printer MicroSD card."

msgid "Slice ok."
msgstr "Slice complete"

msgid "View all Daily tips"
msgstr ""

msgid "Failed to create socket"
msgstr ""

msgid "Failed to connect socket"
msgstr ""

msgid "Failed to publish login request"
msgstr ""

msgid "Get ticket from device timeout"
msgstr "Timeout getting ticket from device"

msgid "Get ticket from server timeout"
msgstr "Timeout getting ticket from server"

msgid "Failed to post ticket to server"
msgstr ""

msgid "Failed to parse login report reason"
msgstr ""

msgid "Receive login report timeout"
msgstr ""

msgid "Unknown Failure"
msgstr ""

msgid ""
"Please Find the Pin Code in Account page on printer screen,\n"
" and type in the Pin Code below."
msgstr ""

msgid "Can't find Pin Code?"
msgstr ""

msgid "Pin Code"
msgstr ""

msgid "Binding..."
msgstr ""

msgid "Please confirm on the printer screen"
msgstr ""

msgid "Log in failed. Please check the Pin Code."
msgstr ""

msgid "Log in printer"
msgstr ""

msgid "Would you like to log in to this printer with the current account?"
msgstr ""

msgid "Check the reason"
msgstr ""

msgid "Read and accept"
msgstr ""

msgid "Terms and Conditions"
msgstr ""

msgid ""
"Thank you for purchasing a Bambu Lab device. Before using your Bambu Lab "
"device, please read the terms and conditions. By clicking to agree to use "
"your Bambu Lab device, you agree to abide by the Privacy Policy and Terms of "
"Use (collectively, the \"Terms\"). If you do not comply with or agree to the "
"Bambu Lab Privacy Policy, please do not use Bambu Lab equipment and services."
msgstr ""

msgid "and"
msgstr ""

msgid "Privacy Policy"
msgstr ""

msgid "We ask for your help to improve everyone's printer"
msgstr ""

msgid "Statement about User Experience Improvement Program"
msgstr ""

#, c-format, boost-format
msgid ""
"In the 3D Printing community, we learn from each other's successes and "
"failures to adjust our own slicing parameters and settings. %s follows the "
"same principle and uses machine learning to improve its performance from the "
"successes and failures of the vast number of prints by our users. We are "
"training %s to be smarter by feeding them the real-world data. If you are "
"willing, this service will access information from your error logs and usage "
"logs, which may include information described in Privacy Policy. We will "
"not collect any Personal Data by which an individual can be identified "
"directly or indirectly, including without limitation names, addresses, "
"payment information, or phone numbers. By enabling this service, you agree "
"to these terms and the statement about Privacy Policy."
msgstr ""

msgid "Statement on User Experience Improvement Plan"
msgstr ""

msgid "Log in successful."
msgstr ""

msgid "Log out printer"
msgstr ""

msgid "Would you like to log out the printer?"
msgstr ""

msgid "Please log in first."
msgstr ""

msgid "There was a problem connecting to the printer. Please try again."
msgstr ""

msgid "Failed to log out."
msgstr ""

#. TRN "Save current Settings"
#, c-format, boost-format
msgid "Save current %s"
msgstr ""

msgid "Delete this preset"
msgstr ""

msgid "Search in preset"
msgstr ""

msgid "Click to reset all settings to the last saved preset."
msgstr ""

msgid ""
"A prime tower is required for smooth timelapse. There may be flaws on the "
"model without prime tower. Are you sure you want to disable prime tower?"
msgstr ""
"A prime tower is required for smooth timelapse mode. There may be flaws on "
"the model without a prime tower. Are you sure you want to disable the prime "
"tower?"

msgid ""
"A prime tower is required for smooth timelapse. There may be flaws on the "
"model without prime tower. Do you want to enable prime tower?"
msgstr ""
"A prime tower is required for smooth timelapse mode. There may be flaws on "
"the model without prime tower. Do you want to enable the prime tower?"

msgid "Still print by object?"
msgstr ""

msgid ""
"When using support material for the support interface, we recommend the "
"following settings:\n"
"0 top Z distance, 0 interface spacing, interlaced rectilinear pattern and "
"disable independent support layer height"
msgstr ""

msgid ""
"Change these settings automatically?\n"
"Yes - Change these settings automatically\n"
"No  - Do not change these settings for me"
msgstr ""
"Change these settings automatically?\n"
"Yes - Change these settings automatically.\n"
"No  - Do not change these settings for me."

msgid ""
"Enabling this option will modify the model's shape. If your print requires "
"precise dimensions or is part of an assembly, it's important to double-check "
"whether this change in geometry impacts the functionality of your print."
msgstr ""

msgid "Are you sure you want to enable this option?"
msgstr ""

msgid ""
"Layer height is too small.\n"
"It will set to min_layer_height\n"
msgstr ""

msgid ""
"Layer height exceeds the limit in Printer Settings -> Extruder -> Layer "
"height limits, this may cause printing quality issues."
msgstr ""

msgid "Adjust to the set range automatically?\n"
msgstr ""

msgid "Adjust"
msgstr ""

msgid "Ignore"
msgstr ""

msgid ""
"Experimental feature: Retracting and cutting off the filament at a greater "
"distance during filament changes to minimize flush. Although it can notably "
"reduce flush, it may also elevate the risk of nozzle clogs or other "
"printing complications."
msgstr ""

msgid ""
"Experimental feature: Retracting and cutting off the filament at a greater "
"distance during filament changes to minimize flush. Although it can notably "
"reduce flush, it may also elevate the risk of nozzle clogs or other printing "
"complications. Please use with the latest printer firmware."
msgstr ""

msgid ""
"When recording timelapse without toolhead, it is recommended to add a "
"\"Timelapse Wipe Tower\" \n"
"by right-click the empty position of build plate and choose \"Add "
"Primitive\"->\"Timelapse Wipe Tower\"."
msgstr ""

msgid ""
"A copy of the current system preset will be created, which will be detached "
"from the system preset."
msgstr ""

msgid ""
"The current custom preset will be detached from the parent system preset."
msgstr ""

msgid "Modifications to the current profile will be saved."
msgstr ""

msgid ""
"This action is not revertible.\n"
"Do you want to proceed?"
msgstr ""

msgid "Detach preset"
msgstr ""

msgid "This is a default preset."
msgstr ""

msgid "This is a system preset."
msgstr ""

msgid "Current preset is inherited from the default preset."
msgstr ""

msgid "Current preset is inherited from"
msgstr ""

msgid "It can't be deleted or modified."
msgstr ""

msgid ""
"Any modifications should be saved as a new preset inherited from this one."
msgstr ""

msgid "To do that please specify a new name for the preset."
msgstr ""

msgid "Additional information:"
msgstr ""

msgid "vendor"
msgstr ""

msgid "printer model"
msgstr ""

msgid "default print profile"
msgstr ""

msgid "default filament profile"
msgstr ""

msgid "default SLA material profile"
msgstr ""

msgid "default SLA print profile"
msgstr ""

msgid "full profile name"
msgstr ""

msgid "symbolic profile name"
msgstr ""

msgid "Line width"
msgstr ""

msgid "Seam"
msgstr ""

msgid "Precision"
msgstr ""

msgid "Wall generator"
msgstr ""

msgid "Walls and surfaces"
msgstr ""

msgid "Bridging"
msgstr ""

msgid "Overhangs"
msgstr ""

msgid "Walls"
msgstr ""

msgid "Top/bottom shells"
msgstr ""

msgid "Initial layer speed"
msgstr "First layer speed"

msgid "Other layers speed"
msgstr ""

msgid "Overhang speed"
msgstr ""

msgid ""
"This is the speed for various overhang degrees. Overhang degrees are "
"expressed as a percentage of line width. 0 speed means no slowing down for "
"the overhang degree range and wall speed is used"
msgstr ""

msgid "Bridge"
msgstr ""

msgid "Set speed for external and internal bridges"
msgstr ""

msgid "Travel speed"
msgstr ""

msgid "Acceleration"
msgstr ""

msgid "Jerk(XY)"
msgstr ""

msgid "Raft"
msgstr ""

msgid "Support filament"
msgstr "Filament for Supports"

msgid "Tree supports"
msgstr ""

msgid "Multimaterial"
msgstr ""

msgid "Prime tower"
msgstr ""

msgid "Filament for Features"
msgstr ""

msgid "Ooze prevention"
msgstr ""

msgid "Skirt"
msgstr ""

msgid "Special mode"
msgstr ""

msgid "G-code output"
msgstr ""

msgid "Post-processing Scripts"
msgstr ""

msgid "Notes"
msgstr ""

msgid "Frequent"
msgstr ""

#, c-format, boost-format
msgid ""
"Following line %s contains reserved keywords.\n"
"Please remove it, or will beat G-code visualization and printing time "
"estimation."
msgid_plural ""
"Following lines %s contain reserved keywords.\n"
"Please remove them, or will beat G-code visualization and printing time "
"estimation."
msgstr[0] ""
"Following line %s contains reserved keywords.\n"
"Please remove it, or G-code visualization and print time estimation will be "
"broken."
msgstr[1] ""
"Following lines %s contain reserved keywords.\n"
"Please remove them, or G-code visualization and print time estimation will "
"be broken."

msgid "Reserved keywords found"
msgstr ""

msgid "Setting Overrides"
msgstr ""

msgid "Retraction"
msgstr ""

msgid "Basic information"
msgstr ""

msgid "Recommended nozzle temperature"
msgstr ""

msgid "Recommended nozzle temperature range of this filament. 0 means no set"
msgstr "Recommended nozzle temperature range of this filament. 0 means not set"

msgid "Flow ratio and Pressure Advance"
msgstr ""

msgid "Print chamber temperature"
msgstr ""

msgid "Print temperature"
msgstr ""

msgid "Nozzle"
msgstr ""

msgid "Nozzle temperature when printing"
msgstr ""

msgid "Cool Plate (SuperTack)"
msgstr ""

msgid ""
"Bed temperature when the Cool Plate Supertack is installed. A value of 0 "
"means the filament does not support printing on the Cool Plate SuperTack."
msgstr ""
"This is the bed temperature when the Cool Plate Supertack is installed. A "
"value of 0 means the filament does not support printing on the Cool Plate "
"SuperTack."

msgid "Cool Plate"
msgstr ""

msgid ""
"Bed temperature when the Cool Plate is installed. A value of 0 means the "
"filament does not support printing on the Cool Plate."
msgstr ""
"This is the bed temperature when the Cool Plate is installed. A value of 0 "
"means the filament does not support printing on the Cool Plate."

msgid "Textured Cool Plate"
msgstr ""

msgid ""
"Bed temperature when the Textured Cool Plate is installed. A value of 0 "
"means the filament does not support printing on the Textured Cool Plate."
msgstr ""
"This is the bed temperature when the Textured Cool Plate is installed. A "
"value of 0 means the filament does not support printing on the Textured Cool "
"Plate."

msgid "Engineering Plate"
msgstr ""

msgid ""
"Bed temperature when the Engineering Plate is installed. A value of 0 means "
"the filament does not support printing on the Engineering Plate."
msgstr ""
"This is the bed temperature when the engineering plate is installed. A value "
"of 0 means the filament does not support printing on the Engineering Plate."

msgid "Smooth PEI Plate / High Temp Plate"
msgstr ""

msgid ""
"Bed temperature when the Smooth PEI Plate/High Temperature Plate is "
"installed. A value of 0 means the filament does not support printing on the "
"Smooth PEI Plate/High Temp Plate."
msgstr ""
"This is the bed temperature when the Smooth PEI Plate/High Temperature Plate "
"is installed. A value of 0 means the filament does not support printing on "
"the Smooth PEI Plate/High Temp Plate."

msgid "Textured PEI Plate"
msgstr ""

msgid ""
"Bed temperature when the Textured PEI Plate is installed. A value of 0 means "
"the filament does not support printing on the Textured PEI Plate."
msgstr ""
"This is the bed temperature when the Textured PEI Plate is installed. A "
"value of 0 means the filament does not support printing on the Textured "
"PEI Plate."

msgid "Volumetric speed limitation"
msgstr ""

msgid "Cooling"
msgstr ""

msgid "Cooling for specific layer"
msgstr ""

msgid "Part cooling fan"
msgstr ""

msgid "Min fan speed threshold"
msgstr ""

msgid ""
"Part cooling fan speed will start to run at min speed when the estimated "
"layer time is no longer than the layer time in setting. When layer time is "
"shorter than threshold, fan speed is interpolated between the minimum and "
"maximum fan speed according to layer printing time"
msgstr ""
"The part cooling fan will run at the minimum fan speed when the estimated "
"layer time is longer than the threshold value. When the layer time is "
"shorter than the threshold, the fan speed will be interpolated between the "
"minimum and maximum fan speed according to layer printing time."

msgid "Max fan speed threshold"
msgstr ""

msgid ""
"Part cooling fan speed will be max when the estimated layer time is shorter "
"than the setting value"
msgstr ""
"The part cooling fan will run at maximum speed when the estimated layer time "
"is shorter than the threshold value."

msgid "Auxiliary part cooling fan"
msgstr ""

msgid "Exhaust fan"
msgstr ""

msgid "During print"
msgstr ""

msgid "Complete print"
msgstr ""

msgid "Filament start G-code"
msgstr ""

msgid "Filament end G-code"
msgstr ""

msgid "Wipe tower parameters"
msgstr ""

msgid "Tool change parameters with single extruder MM printers"
msgstr ""

msgid "Ramming settings"
msgstr ""

msgid "Tool change parameters with multi extruder MM printers"
msgstr ""

msgid "Dependencies"
msgstr ""

msgid "Profile dependencies"
msgstr ""

msgid "Printable space"
msgstr ""

#. TRN: The first argument is the parameter's name; the second argument is its value.
#, boost-format
msgid "Invalid value provided for parameter %1%: %2%"
msgstr ""

msgid "G-code flavor is switched"
msgstr ""

msgid "Cooling Fan"
msgstr ""

msgid "Fan speed-up time"
msgstr ""

msgid "Extruder Clearance"
msgstr ""

msgid "Adaptive bed mesh"
msgstr ""

msgid "Accessory"
msgstr ""

msgid "Machine G-code"
msgstr ""

msgid "Machine start G-code"
msgstr ""

msgid "Machine end G-code"
msgstr ""

msgid "Printing by object G-code"
msgstr ""

msgid "Before layer change G-code"
msgstr ""

msgid "Layer change G-code"
msgstr ""

msgid "Timelapse G-code"
msgstr ""

msgid "Change filament G-code"
msgstr ""

msgid "Change extrusion role G-code"
msgstr ""

msgid "Pause G-code"
msgstr ""

msgid "Template Custom G-code"
msgstr ""

msgid "Motion ability"
msgstr ""

msgid "Normal"
msgstr ""

msgid "Speed limitation"
msgstr ""

msgid "Acceleration limitation"
msgstr ""

msgid "Jerk limitation"
msgstr ""

msgid "Single extruder multi-material setup"
msgstr ""

msgid "Number of extruders of the printer."
msgstr ""

msgid ""
"Single Extruder Multi Material is selected, \n"
"and all extruders must have the same diameter.\n"
"Do you want to change the diameter for all extruders to first extruder "
"nozzle diameter value?"
msgstr ""

msgid "Nozzle diameter"
msgstr ""

msgid "Wipe tower"
msgstr ""

msgid "Single extruder multi-material parameters"
msgstr ""

msgid ""
"This is a single extruder multi-material printer, diameters of all extruders "
"will be set to the new value. Do you want to proceed?"
msgstr ""

msgid "Layer height limits"
msgstr ""

msgid "Z-Hop"
msgstr ""

msgid "Retraction when switching material"
msgstr ""

msgid ""
"The Wipe option is not available when using the Firmware Retraction mode.\n"
"\n"
"Shall I disable it in order to enable Firmware Retraction?"
msgstr ""
"The Wipe option is not available when using the Firmware Retraction mode.\n"
"\n"
"Disable it in order to enable Firmware Retraction?"

msgid "Firmware Retraction"
msgstr ""

msgid "Detached"
msgstr ""

#, c-format, boost-format
msgid ""
"%d Filament Preset and %d Process Preset is attached to this printer. Those "
"presets would be deleted if the printer is deleted."
msgstr ""

msgid "Presets inherited by other presets cannot be deleted!"
msgstr ""

msgid "The following presets inherit this preset."
msgid_plural "The following preset inherits this preset."
msgstr[0] ""
msgstr[1] ""

#. TRN  Remove/Delete
#, boost-format
msgid "%1% Preset"
msgstr ""

msgid "Following preset will be deleted too."
msgid_plural "Following presets will be deleted too."
msgstr[0] "The following preset will be deleted too:"
msgstr[1] "The following presets will be deleted too:"

msgid ""
"Are you sure to delete the selected preset?\n"
"If the preset corresponds to a filament currently in use on your printer, "
"please reset the filament information for that slot."
msgstr ""

#, boost-format
msgid "Are you sure to %1% the selected preset?"
msgstr "Are you sure you want to %1% the selected preset?"

msgid "All"
msgstr ""

msgid "Set"
msgstr ""

msgid "Click to reset current value and attach to the global value."
msgstr ""

msgid "Click to drop current modify and reset to saved value."
msgstr "Click to drop current modifications and reset to saved value."

msgid "Process Settings"
msgstr ""

msgid "Undef"
msgstr "Undefined"

msgid "Unsaved Changes"
msgstr "unsaved changes"

msgid "Transfer or discard changes"
msgstr ""

msgid "Old Value"
msgstr "Old value"

msgid "New Value"
msgstr ""

msgid "Transfer"
msgstr ""

msgid "Don't save"
msgstr ""

msgid "Discard"
msgstr ""

msgid "Click the right mouse button to display the full text."
msgstr ""

msgid "All changes will not be saved"
msgstr "No changes will be saved."

msgid "All changes will be discarded."
msgstr ""

msgid "Save the selected options."
msgstr ""

msgid "Keep the selected options."
msgstr ""

msgid "Transfer the selected options to the newly selected preset."
msgstr ""

#, boost-format
msgid ""
"Save the selected options to preset \n"
"\"%1%\"."
msgstr ""

#, boost-format
msgid ""
"Transfer the selected options to the newly selected preset \n"
"\"%1%\"."
msgstr ""

#, boost-format
msgid "Preset \"%1%\" contains the following unsaved changes:"
msgstr ""

#, boost-format
msgid ""
"Preset \"%1%\" is not compatible with the new printer profile and it "
"contains the following unsaved changes:"
msgstr ""

#, boost-format
msgid ""
"Preset \"%1%\" is not compatible with the new process profile and it "
"contains the following unsaved changes:"
msgstr ""

#, boost-format
msgid "You have changed some settings of preset \"%1%\"."
msgstr ""

msgid ""
"\n"
"You can save or discard the preset values you have modified."
msgstr ""

msgid ""
"\n"
"You can save or discard the preset values you have modified, or choose to "
"transfer the values you have modified to the new preset."
msgstr ""

msgid "You have previously modified your settings."
msgstr ""

msgid ""
"\n"
"You can discard the preset values you have modified, or choose to transfer "
"the modified values to the new project"
msgstr ""

msgid "Extruders count"
msgstr "Extruder count"

msgid "General"
msgstr ""

msgid "Capabilities"
msgstr ""

msgid "Show all presets (including incompatible)"
msgstr ""

msgid "Select presets to compare"
msgstr ""

msgid ""
"You can only transfer to current active profile because it has been modified."
msgstr ""

msgid ""
"Transfer the selected options from left preset to the right.\n"
"Note: New modified presets will be selected in settings tabs after close "
"this dialog."
msgstr ""

msgid "Transfer values from left to right"
msgstr ""

msgid ""
"If enabled, this dialog can be used for transfer selected values from left "
"to right preset."
msgstr ""

msgid "Add File"
msgstr ""

msgid "Set as cover"
msgstr ""

msgid "Cover"
msgstr ""

#, boost-format
msgid "The name \"%1%\" already exists."
msgstr ""

msgid "Basic Info"
msgstr ""

msgid "Pictures"
msgstr ""

msgid "Bill of Materials"
msgstr ""

msgid "Assembly Guide"
msgstr ""

msgid "Author"
msgstr ""

msgid "Model Name"
msgstr ""

#, c-format, boost-format
msgid "%s Update"
msgstr ""

msgid "A new version is available"
msgstr ""

msgid "Configuration update"
msgstr ""

msgid "A new configuration package is available. Do you want to install it?"
msgstr ""

msgid "Description:"
msgstr ""

msgid "Configuration incompatible"
msgstr ""

msgid "the configuration package is incompatible with the current application."
msgstr ""

#, c-format, boost-format
msgid ""
"The configuration package is incompatible with the current application.\n"
"%s will update the configuration package to allow the application to start."
msgstr ""

#, c-format, boost-format
msgid "Exit %s"
msgstr ""

msgid "the Configuration package is incompatible with the current APP."
msgstr ""
"The configuration package is incompatible with the current version of Bambu "
"Studio."

msgid "Configuration updates"
msgstr ""

msgid "No updates available."
msgstr ""

msgid "The configuration is up to date."
msgstr ""

msgid "Obj file Import color"
msgstr ""

msgid "Specify number of colors:"
msgstr ""

#, c-format, boost-format
msgid "The color count should be in range [%d, %d]."
msgstr ""

msgid "Recommended "
msgstr ""

msgid "Current filament colors:"
msgstr ""

msgid "Quick set:"
msgstr ""

msgid "Color match"
msgstr ""

msgid "Approximate color matching."
msgstr ""

msgid "Append"
msgstr ""

msgid "Add consumable extruder after existing extruders."
msgstr ""

msgid "Reset mapped extruders."
msgstr ""

msgid "Cluster colors"
msgstr ""

msgid "Map Filament"
msgstr ""

msgid ""
"Note: The color has been selected, you can choose OK \n"
"to continue or manually adjust it."
msgstr ""

msgid ""
"Warning: The count of newly added and \n"
"current extruders exceeds 16."
msgstr ""

msgid "Ramming customization"
msgstr ""

msgid ""
"Ramming denotes the rapid extrusion just before a tool change in a single-"
"extruder MM printer. Its purpose is to properly shape the end of the "
"unloaded filament so it does not prevent insertion of the new filament and "
"can itself be reinserted later. This phase is important and different "
"materials can require different extrusion speeds to get the good shape. For "
"this reason, the extrusion rates during ramming are adjustable.\n"
"\n"
"This is an expert-level setting, incorrect adjustment will likely lead to "
"jams, extruder wheel grinding into filament etc."
msgstr ""

msgid "Total ramming time"
msgstr ""

msgid "s"
msgstr ""

msgid "Total rammed volume"
msgstr ""

msgid "Ramming line width"
msgstr ""

msgid "Ramming line spacing"
msgstr ""

msgid "Auto-Calc"
msgstr ""

msgid "Re-calculate"
msgstr ""

msgid "Flushing volumes for filament change"
msgstr ""

msgid ""
"Orca would re-calculate your flushing volumes every time the filaments color "
"changed. You could disable the auto-calculate in Orca Slicer > Preferences"
msgstr ""

msgid "Flushing volume (mm³) for each filament pair."
msgstr ""

#, c-format, boost-format
msgid "Suggestion: Flushing Volume in range [%d, %d]"
msgstr ""

#, c-format, boost-format
msgid "The multiplier should be in range [%.2f, %.2f]."
msgstr ""

msgid "Multiplier"
msgstr ""

msgid "unloaded"
msgstr ""

msgid "loaded"
msgstr ""

msgid "Filament #"
msgstr ""

msgid "From"
msgstr ""

msgid "To"
msgstr ""

msgid ""
"Windows Media Player is required for this task! Do you want to enable "
"'Windows Media Player' for your operation system?"
msgstr ""

msgid ""
"BambuSource has not correctly been registered for media playing! Press Yes "
"to re-register it. You will be promoted twice"
msgstr ""

msgid ""
"Missing BambuSource component registered for media playing! Please re-"
"install BambuStudio or seek after-sales help."
msgstr ""

msgid ""
"Using a BambuSource from a different install, video play may not work "
"correctly! Press Yes to fix it."
msgstr ""

msgid ""
"Your system is missing H.264 codecs for GStreamer, which are required to "
"play video. (Try installing the gstreamer1.0-plugins-bad or gstreamer1.0-"
"libav packages, then restart Orca Slicer?)"
msgstr ""

msgid "Bambu Network plug-in not detected."
msgstr ""

msgid "Click here to download it."
msgstr ""

msgid "Login"
msgstr ""

msgid "The configuration package is changed in previous Config Guide"
msgstr ""

msgid "Configuration package changed"
msgstr ""

msgid "Toolbar"
msgstr ""

msgid "Objects list"
msgstr ""

msgid "Import geometry data from STL/STEP/3MF/OBJ/AMF files"
msgstr ""

msgid "⌘+Shift+G"
msgstr ""

msgid "Ctrl+Shift+G"
msgstr ""

msgid "Paste from clipboard"
msgstr ""

msgid "Show/Hide 3Dconnexion devices settings dialog"
msgstr ""

msgid "Switch table page"
msgstr ""

msgid "Show keyboard shortcuts list"
msgstr ""

msgid "Global shortcuts"
msgstr ""

msgid "Rotate View"
msgstr ""

msgid "Pan View"
msgstr ""

msgid "Mouse wheel"
msgstr ""

msgid "Zoom View"
msgstr ""

msgid "Shift+A"
msgstr ""

msgid "Shift+R"
msgstr ""

msgid ""
"Auto orients selected objects or all objects. If there are selected "
"objects, it just orients the selected ones. Otherwise, it will orient "
"all objects in the current project."
msgstr ""

msgid "Auto orients all objects on the active plate."
msgstr ""

msgid "Shift+Tab"
msgstr ""

msgid "Collapse/Expand the sidebar"
msgstr ""

msgid "⌘+Any arrow"
msgstr ""

msgid "Movement in camera space"
msgstr ""

msgid "⌥+Left mouse button"
msgstr ""

msgid "Select a part"
msgstr ""

msgid "⌘+Left mouse button"
msgstr ""

msgid "Select multiple objects"
msgstr ""

msgid "Ctrl+Any arrow"
msgstr ""

msgid "Alt+Left mouse button"
msgstr ""

msgid "Ctrl+Left mouse button"
msgstr ""

msgid "Shift+Left mouse button"
msgstr ""

msgid "Select objects by rectangle"
msgstr ""

msgid "Arrow Up"
msgstr ""

msgid "Move selection 10 mm in positive Y direction"
msgstr "Move selection 10mm in positive Y direction"

msgid "Arrow Down"
msgstr ""

msgid "Move selection 10 mm in negative Y direction"
msgstr "Move selection 10mm in negative Y direction"

msgid "Arrow Left"
msgstr ""

msgid "Move selection 10 mm in negative X direction"
msgstr "Move selection 10mm in negative X direction"

msgid "Arrow Right"
msgstr ""

msgid "Move selection 10 mm in positive X direction"
msgstr "Move selection 10mm in positive X direction"

msgid "Shift+Any arrow"
msgstr ""

msgid "Movement step set to 1 mm"
msgstr "Movement step set to 1mm"

msgid "keyboard 1-9: set filament for object/part"
msgstr "Keyboard 1-9: set filament for object/part"

msgid "Camera view - Default"
msgstr ""

msgid "Camera view - Top"
msgstr ""

msgid "Camera view - Bottom"
msgstr ""

msgid "Camera view - Front"
msgstr ""

msgid "Camera view - Behind"
msgstr ""

msgid "Camera Angle - Left side"
msgstr ""

msgid "Camera Angle - Right side"
msgstr ""

msgid "Select all objects"
msgstr ""

msgid "Gizmo move"
msgstr ""

msgid "Gizmo scale"
msgstr ""

msgid "Gizmo rotate"
msgstr ""

msgid "Gizmo cut"
msgstr ""

msgid "Gizmo place face on bed"
msgstr ""

msgid "Gizmo mesh boolean"
msgstr ""

msgid "Gizmo SLA support points"
msgstr ""

msgid "Gizmo FDM paint-on seam"
msgstr ""

msgid "Gizmo text emboss/engrave"
msgstr ""

msgid "Gizmo measure"
msgstr ""

msgid "Gizmo assemble"
msgstr ""

msgid "Gizmo brim ears"
msgstr ""

msgid "Zoom in"
msgstr ""

msgid "Zoom out"
msgstr ""

msgid "Switch between Prepare/Preview"
msgstr ""

msgid "Plater"
msgstr ""

msgid "Move: press to snap by 1mm"
msgstr ""

msgid "⌘+Mouse wheel"
msgstr ""

msgid "Support/Color Painting: adjust pen radius"
msgstr ""

msgid "⌥+Mouse wheel"
msgstr ""

msgid "Support/Color Painting: adjust section position"
msgstr ""

msgid "Ctrl+Mouse wheel"
msgstr ""

msgid "Alt+Mouse wheel"
msgstr ""

msgid "Gizmo"
msgstr ""

msgid "Set extruder number for the objects and parts"
msgstr ""

msgid "Delete objects, parts, modifiers"
msgstr "Delete objects, parts, modifiers"

msgid "Select the object/part and press space to change the name"
msgstr ""

msgid "Mouse click"
msgstr ""

msgid "Select the object/part and mouse click to change the name"
msgstr ""

msgid "Objects List"
msgstr ""

msgid "Vertical slider - Move active thumb Up"
msgstr ""

msgid "Vertical slider - Move active thumb Down"
msgstr ""

msgid "Horizontal slider - Move active thumb Left"
msgstr ""

msgid "Horizontal slider - Move active thumb Right"
msgstr ""

msgid "On/Off one layer mode of the vertical slider"
msgstr ""

msgid "On/Off G-code window"
msgstr ""

msgid "Move slider 5x faster"
msgstr ""

msgid "Shift+Mouse wheel"
msgstr ""

msgid "Horizontal slider - Move to start position"
msgstr ""

msgid "Horizontal slider - Move to last position"
msgstr ""

msgid "Release Note"
msgstr ""

#, c-format, boost-format
msgid "version %s update information:"
msgstr ""

msgid "Network plug-in update"
msgstr ""

msgid ""
"Click OK to update the Network plug-in when Orca Slicer launches next time."
msgstr ""
"Click OK to update the Network plug-in the next time Orca Slicer launches."

#, c-format, boost-format
msgid "A new Network plug-in (%s) is available. Do you want to install it?"
msgstr ""

msgid "New version of Orca Slicer"
msgstr ""

msgid "Skip this Version"
msgstr ""

msgid "Done"
msgstr ""

msgid "resume"
msgstr ""

msgid "Resume Printing"
msgstr ""

msgid "Resume Printing (defects acceptable)"
msgstr ""

msgid "Resume Printing (problem solved)"
msgstr ""

msgid "Stop Printing"
msgstr ""

msgid "Check Assistant"
msgstr ""

msgid "Filament Extruded, Continue"
msgstr ""

msgid "Not Extruded Yet, Retry"
msgstr ""

msgid "Finished, Continue"
msgstr ""

msgid "Load Filament"
msgstr "Load"

msgid "Filament Loaded, Resume"
msgstr ""

msgid "View Liveview"
msgstr ""

msgid "Confirm and Update Nozzle"
msgstr ""

msgid "Connect the printer using IP and access code"
msgstr ""

msgid ""
"Step 1. Please confirm Orca Slicer and your printer are in the same LAN."
msgstr ""

msgid ""
"Step 2. If the IP and Access Code below are different from the actual values "
"on your printer, please correct them."
msgstr ""

msgid ""
"Step 3. Please obtain the device SN from the printer side; it is usually "
"found in the device information on the printer screen."
msgstr ""

msgid "IP"
msgstr ""

msgid "Access Code"
msgstr ""

msgid "Printer model"
msgstr ""

msgid "Printer name"
msgstr ""

msgid "Where to find your printer's IP and Access Code?"
msgstr ""

msgid "Connect"
msgstr ""

msgid "Manual Setup"
msgstr ""

msgid "connecting..."
msgstr ""

msgid "Failed to connect to printer."
msgstr ""

msgid "Failed to publish login request."
msgstr ""

msgid "The printer has already been bound."
msgstr ""

msgid "The printer mode is incorrect, please switch to LAN Only."
msgstr ""

msgid "Connecting to printer... The dialog will close later"
msgstr ""

msgid "Connection failed, please double check IP and Access Code"
msgstr ""

msgid ""
"Connection failed! If your IP and Access Code is correct, \n"
"please move to step 3 for troubleshooting network issues"
msgstr ""

msgid "Model:"
msgstr ""

msgid "Serial:"
msgstr ""

msgid "Version:"
msgstr ""

msgid "Update firmware"
msgstr ""

msgid "Beta version"
msgstr ""

msgid "Latest version"
msgstr ""

msgid "Updating"
msgstr ""

msgid "Update failed"
msgstr ""

msgid "Update successful"
msgstr ""

msgid ""
"Are you sure you want to update? This will take about 10 minutes. Do not "
"turn off the power while the printer is updating."
msgstr ""

msgid ""
"An important update was detected and needs to be run before printing can "
"continue. Do you want to update now? You can also update later from 'Upgrade "
"firmware'."
msgstr ""
"An important update was detected and needs to be run before printing can "
"continue. Do you want to update now? You can also update later from 'Update "
"firmware'."

msgid ""
"The firmware version is abnormal. Repairing and updating are required before "
"printing. Do you want to update now? You can also update later on printer or "
"update next time starting Orca."
msgstr ""
"The firmware version is abnormal. Repairing and updating are required before "
"printing. Do you want to update now? You can also update later on the "
"printer or update next time you start Orca Slicer."

msgid "Extension Board"
msgstr ""

msgid "Saving objects into the 3mf failed."
msgstr ""

msgid "Only Windows 10 is supported."
msgstr ""

msgid "Failed to initialize the WinRT library."
msgstr ""

msgid "Exporting objects"
msgstr ""

msgid "Failed loading objects."
msgstr ""

msgid "Repairing object by Windows service"
msgstr ""

msgid "Repair failed."
msgstr ""

msgid "Loading repaired objects"
msgstr ""

msgid "Exporting 3mf file failed"
msgstr ""

msgid "Import 3mf file failed"
msgstr ""

msgid "Repaired 3mf file does not contain any object"
msgstr "The repaired 3mf file does not contain any objects."

msgid "Repaired 3mf file contains more than one object"
msgstr "The repaired 3mf file contains more than one object."

msgid "Repaired 3mf file does not contain any volume"
msgstr "The repaired 3mf file does not contain any volume."

msgid "Repaired 3mf file contains more than one volume"
msgstr "The repaired 3mf file contains more than one volume."

msgid "Repair finished"
msgstr ""

msgid "Repair canceled"
msgstr ""

#, boost-format
msgid "Copying of file %1% to %2% failed: %3%"
msgstr ""

msgid "Need to check the unsaved changes before configuration updates."
msgstr "Please check any unsaved changes before updating the configuration."

msgid "Configuration package: "
msgstr ""

msgid " updated to "
msgstr ""

msgid "Open G-code file:"
msgstr ""

msgid ""
"One object has empty initial layer and can't be printed. Please Cut the "
"bottom or enable supports."
msgstr ""

#, boost-format
msgid "Object can't be printed for empty layer between %1% and %2%."
msgstr "The object has empty layers between %1% and %2% and can’t be printed."

#, boost-format
msgid "Object: %1%"
msgstr ""

msgid ""
"Maybe parts of the object at these height are too thin, or the object has "
"faulty mesh"
msgstr ""
"Parts of the object at these heights may be too thin or the object may have "
"a faulty mesh."

msgid "No object can be printed. Maybe too small"
msgstr "No object can be printed. It may be too small."

msgid ""
"Your print is very close to the priming regions. Make sure there is no "
"collision."
msgstr ""

msgid ""
"Failed to generate G-code for invalid custom G-code.\n"
"\n"
msgstr ""

msgid "Please check the custom G-code or use the default custom G-code."
msgstr ""

#, boost-format
msgid "Generating G-code: layer %1%"
msgstr ""

msgid "Inner wall"
msgstr ""

msgid "Outer wall"
msgstr ""

msgid "Overhang wall"
msgstr ""

msgid "Sparse infill"
msgstr ""

msgid "Internal solid infill"
msgstr ""

msgid "Top surface"
msgstr ""

msgid "Bottom surface"
msgstr ""

msgid "Internal Bridge"
msgstr ""

msgid "Gap infill"
msgstr ""

msgid "Support interface"
msgstr ""

msgid "Support transition"
msgstr ""

msgid "Multiple"
msgstr ""

#, boost-format
msgid "Failed to calculate line width of %1%. Cannot get value of \"%2%\" "
msgstr "Failed to calculate line width of %1%. Cannot get value of “%2%” "

msgid ""
"Invalid spacing supplied to Flow::with_spacing(), check your layer height "
"and extrusion width"
msgstr ""

msgid "undefined error"
msgstr ""

msgid "too many files"
msgstr ""

msgid "file too large"
msgstr "File too large"

msgid "unsupported method"
msgstr ""

msgid "unsupported encryption"
msgstr ""

msgid "unsupported feature"
msgstr ""

msgid "failed finding central directory"
msgstr ""

msgid "not a ZIP archive"
msgstr ""

msgid "invalid header or corrupted"
msgstr ""

msgid "unsupported multidisk"
msgstr "Saving to RAID is not supported."

msgid "decompression failed"
msgstr ""

msgid "compression failed"
msgstr ""

msgid "unexpected decompressed size"
msgstr ""

msgid "CRC check failed"
msgstr ""

msgid "unsupported central directory size"
msgstr ""

msgid "allocation failed"
msgstr ""

msgid "file open failed"
msgstr ""

msgid "file create failed"
msgstr ""

msgid "file write failed"
msgstr ""

msgid "file read failed"
msgstr ""

msgid "file close failed"
msgstr ""

msgid "file seek failed"
msgstr ""

msgid "file stat failed"
msgstr ""

msgid "invalid parameter"
msgstr ""

msgid "invalid filename"
msgstr ""

msgid "buffer too small"
msgstr "Buffer too small"

msgid "internal error"
msgstr ""

msgid "file not found"
msgstr ""

msgid "archive too large"
msgstr "Archive too large"

msgid "validation failed"
msgstr ""

msgid "write callback failed"
msgstr ""

#, boost-format
msgid ""
"%1% is too close to exclusion area, there may be collisions when printing."
msgstr ""
"%1% is too close to exclusion area. There may be collisions when printing."

#, boost-format
msgid "%1% is too close to others, and collisions may be caused."
msgstr ""

#, boost-format
msgid "%1% is too tall, and collisions will be caused."
msgstr ""

msgid " is too close to others, there may be collisions when printing."
msgstr " is too close to others; there may be collisions when printing."

msgid " is too close to exclusion area, there may be collisions when printing."
msgstr ""

msgid "Prime Tower"
msgstr ""

msgid " is too close to others, and collisions may be caused.\n"
msgstr ""

msgid " is too close to exclusion area, and collisions will be caused.\n"
msgstr " is too close to an exclusion area, and collisions will be caused.\n"

msgid ""
"Cannot print multiple filaments which have large difference of temperature "
"together. Otherwise, the extruder and nozzle may be blocked or damaged "
"during printing"
msgstr ""
"Unable to print multiple filaments which have large temperature differences "
"together. Otherwise, the extruder and nozzle may be blocked or damaged "
"during printing."

msgid "No extrusions under current settings."
msgstr ""

msgid ""
"Smooth mode of timelapse is not supported when \"by object\" sequence is "
"enabled."
msgstr ""

msgid ""
"Please select \"By object\" print sequence to print multiple objects in "
"spiral vase mode."
msgstr ""

msgid ""
"The spiral vase mode does not work when an object contains more than one "
"materials."
msgstr ""
"Spiral (vase) mode does not work when an object contains more than one "
"material."

#, boost-format
msgid ""
"While the object %1% itself fits the build volume, it exceeds the maximum "
"build volume height because of material shrinkage compensation."
msgstr ""

#, boost-format
msgid "The object %1% exceeds the maximum build volume height."
msgstr ""

#, boost-format
msgid ""
"While the object %1% itself fits the build volume, its last layer exceeds "
"the maximum build volume height."
msgstr ""

msgid ""
"You might want to reduce the size of your model or change current print "
"settings and retry."
msgstr ""

msgid "Variable layer height is not supported with Organic supports."
msgstr ""

msgid ""
"Different nozzle diameters and different filament diameters may not work "
"well when the prime tower is enabled. It's very experimental, so please "
"proceed with caution."
msgstr ""

msgid ""
"The Wipe Tower is currently only supported with the relative extruder "
"addressing (use_relative_e_distances=1)."
msgstr ""

msgid ""
"Ooze prevention is only supported with the wipe tower when "
"'single_extruder_multi_material' is off."
msgstr ""

msgid ""
"The prime tower is currently only supported for the Marlin, RepRap/Sprinter, "
"RepRapFirmware and Repetier G-code flavors."
msgstr ""

msgid "The prime tower is not supported in \"By object\" print."
msgstr "A prime tower is not supported in “By object” print."

msgid ""
"The prime tower is not supported when adaptive layer height is on. It "
"requires that all objects have the same layer height."
msgstr ""
"A prime tower is not supported when adaptive layer height is on. It requires "
"that all objects have the same layer height."

msgid "The prime tower requires \"support gap\" to be multiple of layer height"
msgstr ""
"A prime tower requires any “support gap” to be a multiple of layer height."

msgid "The prime tower requires that all objects have the same layer heights"
msgstr "A prime tower requires that all objects have the same layer height."

msgid ""
"The prime tower requires that all objects are printed over the same number "
"of raft layers"
msgstr ""
"A prime tower requires that all objects are printed over the same number of "
"raft layers."

msgid ""
"The prime tower is only supported for multiple objects if they are printed "
"with the same support_top_z_distance"
msgstr ""

msgid ""
"The prime tower requires that all objects are sliced with the same layer "
"heights."
msgstr ""
"A prime tower requires that all objects are sliced with the same layer "
"height."

msgid ""
"The prime tower is only supported if all objects have the same variable "
"layer height"
msgstr ""

msgid ""
"One or more object were assigned an extruder that the printer does not have."
msgstr ""

msgid "Too small line width"
msgstr "Line width too small"

msgid "Too large line width"
msgstr "Line width too large"

msgid ""
"Printing with multiple extruders of differing nozzle diameters. If support "
"is to be printed with the current filament (support_filament == 0 or "
"support_interface_filament == 0), all nozzles have to be of the same "
"diameter."
msgstr ""

msgid ""
"The prime tower requires that support has the same layer height with object."
msgstr ""
"A prime tower requires that support has the same layer height as the object."

msgid ""
"Organic support tree tip diameter must not be smaller than support material "
"extrusion width."
msgstr ""

msgid ""
"Organic support branch diameter must not be smaller than 2x support material "
"extrusion width."
msgstr ""

msgid ""
"Organic support branch diameter must not be smaller than support tree tip "
"diameter."
msgstr ""

msgid ""
"Support enforcers are used but support is not enabled. Please enable support."
msgstr ""

msgid "Layer height cannot exceed nozzle diameter"
msgstr "Layer height cannot exceed nozzle diameter."

msgid ""
"Relative extruder addressing requires resetting the extruder position at "
"each layer to prevent loss of floating point accuracy. Add \"G92 E0\" to "
"layer_gcode."
msgstr ""

msgid ""
"\"G92 E0\" was found in before_layer_gcode, which is incompatible with "
"absolute extruder addressing."
msgstr ""

msgid ""
"\"G92 E0\" was found in layer_gcode, which is incompatible with absolute "
"extruder addressing."
msgstr ""

#, c-format, boost-format
msgid "Plate %d: %s does not support filament %s"
msgstr ""

msgid ""
"Setting the jerk speed too low could lead to artifacts on curved surfaces"
msgstr ""

msgid ""
"The jerk setting exceeds the printer's maximum jerk (machine_max_jerk_x/"
"machine_max_jerk_y).\n"
"Orca will automatically cap the jerk speed to ensure it doesn't surpass the "
"printer's capabilities.\n"
"You can adjust the maximum jerk setting in your printer's configuration to "
"get higher speeds."
msgstr ""

msgid ""
"The acceleration setting exceeds the printer's maximum acceleration "
"(machine_max_acceleration_extruding).\n"
"Orca will automatically cap the acceleration speed to ensure it doesn't "
"surpass the printer's capabilities.\n"
"You can adjust the machine_max_acceleration_extruding value in your "
"printer's configuration to get higher speeds."
msgstr ""

msgid ""
"The travel acceleration setting exceeds the printer's maximum travel "
"acceleration (machine_max_acceleration_travel).\n"
"Orca will automatically cap the travel acceleration speed to ensure it "
"doesn't surpass the printer's capabilities.\n"
"You can adjust the machine_max_acceleration_travel value in your printer's "
"configuration to get higher speeds."
msgstr ""

msgid ""
"Filament shrinkage will not be used because filament shrinkage for the used "
"filaments differs significantly."
msgstr ""

msgid "Generating skirt & brim"
msgstr ""

msgid "Exporting G-code"
msgstr ""

msgid "Generating G-code"
msgstr ""

msgid "Failed processing of the filename_format template."
msgstr "Processing of the filename_format template failed."

msgid "Printer technology"
msgstr ""

msgid "Printable area"
msgstr ""

msgid "Bed exclude area"
msgstr "Excluded bed area"

msgid ""
"Unprintable area in XY plane. For example, X1 Series printers use the front "
"left corner to cut filament during filament change. The area is expressed as "
"polygon by points in following format: \"XxY, XxY, ...\""
msgstr ""

msgid "Bed custom texture"
msgstr ""

msgid "Bed custom model"
msgstr ""

msgid "Elephant foot compensation"
msgstr ""

msgid ""
"Shrink the initial layer on build plate to compensate for elephant foot "
"effect"
msgstr ""
"This shrinks the first layer on the build plate to compensate for elephant "
"foot effect."

msgid "Elephant foot compensation layers"
msgstr ""

msgid ""
"The number of layers on which the elephant foot compensation will be active. "
"The first layer will be shrunk by the elephant foot compensation value, then "
"the next layers will be linearly shrunk less, up to the layer indicated by "
"this value."
msgstr ""

msgid "layers"
msgstr ""

msgid ""
"Slicing height for each layer. Smaller layer height means more accurate and "
"more printing time"
msgstr ""
"This is the height for each layer. Smaller layer heights give greater "
"accuracy but longer printing time."

msgid "Printable height"
msgstr ""

msgid "Maximum printable height which is limited by mechanism of printer"
msgstr ""
"This is the maximum printable height which is limited by the height of the "
"build area."

msgid "Preferred orientation"
msgstr ""

msgid "Automatically orient stls on the Z-axis upon initial import"
msgstr ""

msgid "Printer preset names"
msgstr ""

msgid "Use 3rd-party print host"
msgstr ""

msgid "Allow controlling BambuLab's printer through 3rd party print hosts"
msgstr ""

msgid "Hostname, IP or URL"
msgstr ""

msgid ""
"Orca Slicer can upload G-code files to a printer host. This field should "
"contain the hostname, IP address or URL of the printer host instance. Print "
"host behind HAProxy with basic auth enabled can be accessed by putting the "
"user name and password into the URL in the following format: https://"
"username:password@your-octopi-address/"
msgstr ""

msgid "Device UI"
msgstr ""

msgid ""
"Specify the URL of your device user interface if it's not same as print_host"
msgstr ""

msgid "API Key / Password"
msgstr ""

msgid ""
"Orca Slicer can upload G-code files to a printer host. This field should "
"contain the API Key or the password required for authentication."
msgstr ""

msgid "Name of the printer"
msgstr ""

msgid "HTTPS CA File"
msgstr ""

msgid ""
"Custom CA certificate file can be specified for HTTPS OctoPrint connections, "
"in crt/pem format. If left blank, the default OS CA certificate repository "
"is used."
msgstr ""

msgid "User"
msgstr ""

msgid "Password"
msgstr ""

msgid "Ignore HTTPS certificate revocation checks"
msgstr ""

msgid ""
"Ignore HTTPS certificate revocation checks in case of missing or offline "
"distribution points. One may want to enable this option for self signed "
"certificates if connection fails."
msgstr ""
"Ignore HTTPS certificate revocation checks in the case of missing or offline "
"distribution points. One may want to enable this option for self signed "
"certificates if connection fails."

msgid "Names of presets related to the physical printer"
msgstr ""

msgid "Authorization Type"
msgstr ""

msgid "API key"
msgstr ""

msgid "HTTP digest"
msgstr ""

msgid "Avoid crossing walls"
msgstr ""

msgid ""
"Detour to avoid traveling across walls, which may cause blobs on the surface."
msgstr ""
"This detours to avoid traveling across walls, which may cause blobs on the "
"surface."

msgid "Avoid crossing walls - Max detour length"
msgstr ""

msgid ""
"Maximum detour distance for avoiding crossing wall. Don't detour if the "
"detour distance is larger than this value. Detour length could be specified "
"either as an absolute value or as percentage (for example 50%) of a direct "
"travel path. Zero to disable."
msgstr ""
"Maximum detour distance for avoiding crossing wall: The printer won't detour "
"if the detour distance is larger than this value. Detour length could be "
"specified either as an absolute value or as percentage (for example 50%) of "
"a direct travel path. A value of 0 will disable this."

msgid "mm or %"
msgstr ""

msgid "Other layers"
msgstr ""

msgid ""
"Bed temperature for layers except the initial one. A value of 0 means the "
"filament does not support printing on the Cool Plate."
msgstr ""
"This is the bed temperature for layers except for the first one. A value of "
"0 means the filament does not support printing on the Cool Plate."

msgid "°C"
msgstr ""

msgid ""
"Bed temperature for layers except the initial one. A value of 0 means the "
"filament does not support printing on the Textured Cool Plate."
msgstr ""
"This is the bed temperature for layers except for the first one. A value of "
"0 means the filament does not support printing on the Textured Cool Plate."

msgid ""
"Bed temperature for layers except the initial one. A value of 0 means the "
"filament does not support printing on the Engineering Plate."
msgstr ""
"This is the bed temperature for layers except for the first one. A value of "
"0 means the filament does not support printing on the Engineering Plate."

msgid ""
"Bed temperature for layers except the initial one. A value of 0 means the "
"filament does not support printing on the High Temp Plate."
msgstr ""
"This is the bed temperature for layers except for the first one. A value of "
"0 means the filament does not support printing on the High Temp Plate."

msgid ""
"Bed temperature for layers except the initial one. A value of 0 means the "
"filament does not support printing on the Textured PEI Plate."
msgstr ""
"This is the bed temperature for layers except for the first one. A value of "
"0 means the filament does not support printing on the Textured PEI Plate."

msgid "Initial layer"
msgstr "First layer"

msgid "Initial layer bed temperature"
msgstr "First layer bed temperature"

msgid ""
"Bed temperature of the initial layer. A value of 0 means the filament does "
"not support printing on the Cool Plate SuperTack."
msgstr ""
"This is the bed temperature of the first layer. A value of 0 means the "
"filament does not support printing on the Cool Plate SuperTack."

msgid ""
"Bed temperature of the initial layer. A value of 0 means the filament does "
"not support printing on the Cool Plate."
msgstr ""
"This is the bed temperature of the first layer. A value of 0 means the "
"filament does not support printing on the Cool Plate."

msgid ""
"Bed temperature of the initial layer. A value of 0 means the filament does "
"not support printing on the Textured Cool Plate."
msgstr ""
"This is the bed temperature of the first layer. A value of 0 means the "
"filament does not support printing on the Textured Cool Plate."

msgid ""
"Bed temperature of the initial layer. A value of 0 means the filament does "
"not support printing on the Engineering Plate."
msgstr ""
"This is the bed temperature of the first layer. A value of 0 means the "
"filament does not support printing on the Engineering Plate."

msgid ""
"Bed temperature of the initial layer. A value of 0 means the filament does "
"not support printing on the High Temp Plate."
msgstr ""
"This is the bed temperature of the first layer. A value of 0 means the "
"filament does not support printing on the High Temp Plate."

msgid ""
"Bed temperature of the initial layer. A value of 0 means the filament does "
"not support printing on the Textured PEI Plate."
msgstr ""
"This is the bed temperature of the first layer. A value of 0 means the "
"filament does not support printing on the Textured PEI Plate."

msgid "Bed types supported by the printer"
msgstr "Plate types supported by the printer"

msgid "Smooth Cool Plate"
msgstr ""

msgid "Smooth High Temp Plate"
msgstr ""

msgid "First layer print sequence"
msgstr ""

msgid "Other layers print sequence"
msgstr ""

msgid "The number of other layers print sequence"
msgstr ""

msgid "Other layers filament sequence"
msgstr ""

msgid "This G-code is inserted at every layer change before lifting z"
msgstr "This G-code is inserted at every layer change before lifting z."

msgid "Bottom shell layers"
msgstr ""

msgid ""
"This is the number of solid layers of bottom shell, including the bottom "
"surface layer. When the thickness calculated by this value is thinner than "
"bottom shell thickness, the bottom shell layers will be increased"
msgstr ""

msgid "Bottom shell thickness"
msgstr ""

msgid ""
"The number of bottom solid layers is increased when slicing if the thickness "
"calculated by bottom shell layers is thinner than this value. This can avoid "
"having too thin shell when layer height is small. 0 means that this setting "
"is disabled and thickness of bottom shell is absolutely determined by bottom "
"shell layers"
msgstr ""
"The number of bottom solid layers is increased when slicing if the thickness "
"calculated by bottom shell layers is thinner than this value. This can avoid "
"having too thin a shell when layer height is small. 0 means that this "
"setting is disabled and the thickness of the bottom shell is determined "
"simply by the number of bottom shell layers."

msgid "Apply gap fill"
msgstr ""

msgid ""
"Enables gap fill for the selected solid surfaces. The minimum gap length "
"that will be filled can be controlled from the filter out tiny gaps option "
"below.\n"
"\n"
"Options:\n"
"1. Everywhere: Applies gap fill to top, bottom and internal solid surfaces "
"for maximum strength\n"
"2. Top and Bottom surfaces: Applies gap fill to top and bottom surfaces "
"only, balancing print speed, reducing potential over extrusion in the solid "
"infill and making sure the top and bottom surfaces have no pin hole gaps\n"
"3. Nowhere: Disables gap fill for all solid infill areas.\n"
"\n"
"Note that if using the classic perimeter generator, gap fill may also be "
"generated between perimeters, if a full width line cannot fit between them. "
"That perimeter gap fill is not controlled by this setting.\n"
"\n"
"If you would like all gap fill, including the classic perimeter generated "
"one, removed, set the filter out tiny gaps value to a large number, like "
"999999.\n"
"\n"
"However this is not advised, as gap fill between perimeters is contributing "
"to the model's strength. For models where excessive gap fill is generated "
"between perimeters, a better option would be to switch to the arachne wall "
"generator and use this option to control whether the cosmetic top and bottom "
"surface gap fill is generated"
msgstr ""

msgid "Everywhere"
msgstr ""

msgid "Top and bottom surfaces"
msgstr ""

msgid "Nowhere"
msgstr ""

msgid "Force cooling for overhangs and bridges"
msgstr ""

msgid ""
"Enable this option to allow adjustment of the part cooling fan speed for "
"specifically for overhangs, internal and external bridges. Setting the fan "
"speed specifically for these features can improve overall print quality and "
"reduce warping."
msgstr ""

msgid "Overhangs and external bridges fan speed"
msgstr ""

msgid ""
"Use this part cooling fan speed when printing bridges or overhang walls with "
"an overhang threshold that exceeds the value set in the 'Overhangs cooling "
"threshold' parameter above. Increasing the cooling specifically for "
"overhangs and bridges can improve the overall print quality of these "
"features.\n"
"\n"
"Please note, this fan speed is clamped on the lower end by the minimum fan "
"speed threshold set above. It is also adjusted upwards up to the maximum fan "
"speed threshold when the minimum layer time threshold is not met."
msgstr ""

msgid "Overhang cooling activation threshold"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"When the overhang exceeds this specified threshold, force the cooling fan to "
"run at the 'Overhang Fan Speed' set below. This threshold is expressed as a "
"percentage, indicating the portion of each line's width that is unsupported "
"by the layer beneath it. Setting this value to 0% forces the cooling fan to "
"run for all outer walls, regardless of the overhang degree."
msgstr ""

msgid "External bridge infill direction"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Bridging angle override. If left to zero, the bridging angle will be "
"calculated automatically. Otherwise the provided angle will be used for "
"external bridges. Use 180°for zero angle."
msgstr ""
"Bridging angle override. 0 means the bridging angle will be calculated "
"automatically. Otherwise the provided angle will be used for external "
"bridges. Use 180° for zero angle."

msgid "Internal bridge infill direction"
msgstr ""

msgid ""
"Internal bridging angle override. If left to zero, the bridging angle will "
"be calculated automatically. Otherwise the provided angle will be used for "
"internal bridges. Use 180°for zero angle.\n"
"\n"
"It is recommended to leave it at 0 unless there is a specific model need not "
"to."
msgstr ""

msgid "External bridge density"
msgstr ""

msgid ""
"Controls the density (spacing) of external bridge lines. 100% means solid "
"bridge. Default is 100%.\n"
"\n"
"Lower density external bridges can help improve reliability as there is more "
"space for air to circulate around the extruded bridge, improving its cooling "
"speed."
msgstr ""

msgid "Internal bridge density"
msgstr ""

msgid ""
"Controls the density (spacing) of internal bridge lines. 100% means solid "
"bridge. Default is 100%.\n"
"\n"
"Lower density internal bridges can help reduce top surface pillowing and "
"improve internal bridge reliability as there is more space for air to "
"circulate around the extruded bridge, improving its cooling speed.\n"
"\n"
"This option works particularly well when combined with the second internal "
"bridge over infill option, further improving internal bridging structure "
"before solid infill is extruded."
msgstr ""

msgid "Bridge flow ratio"
msgstr ""

msgid ""
"Decrease this value slightly (for example 0.9) to reduce the amount of "
"material for bridge, to improve sag.\n"
"\n"
"The actual bridge flow used is calculated by multiplying this value with the "
"filament flow ratio, and if set, the object's flow ratio."
msgstr ""

msgid "Internal bridge flow ratio"
msgstr ""

msgid ""
"This value governs the thickness of the internal bridge layer. This is the "
"first layer over sparse infill. Decrease this value slightly (for example "
"0.9) to improve surface quality over sparse infill.\n"
"\n"
"The actual internal bridge flow used is calculated by multiplying this value "
"with the bridge flow ratio, the filament flow ratio, and if set, the "
"object's flow ratio."
msgstr ""

msgid "Top surface flow ratio"
msgstr ""

msgid ""
"This factor affects the amount of material for top solid infill. You can "
"decrease it slightly to have smooth surface finish.\n"
"\n"
"The actual top surface flow used is calculated by multiplying this value "
"with the filament flow ratio, and if set, the object's flow ratio."
msgstr ""

msgid "Bottom surface flow ratio"
msgstr ""

msgid ""
"This factor affects the amount of material for bottom solid infill.\n"
"\n"
"The actual bottom solid infill flow used is calculated by multiplying this "
"value with the filament flow ratio, and if set, the object's flow ratio."
msgstr ""

msgid "Precise wall"
msgstr ""

msgid ""
"Improve shell precision by adjusting outer wall spacing. This also improves "
"layer consistency."
msgstr ""

msgid "Only one wall on top surfaces"
msgstr ""

msgid ""
"Use only one wall on flat top surface, to give more space to the top infill "
"pattern"
msgstr ""
"Use only one wall on flat top surfaces, to give more space to the top infill "
"pattern"

msgid "One wall threshold"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"If a top surface has to be printed and it's partially covered by another "
"layer, it won't be considered at a top layer where its width is below this "
"value. This can be useful to not let the 'one perimeter on top' trigger on "
"surface that should be covered only by perimeters. This value can be a mm or "
"a % of the perimeter extrusion width.\n"
"Warning: If enabled, artifacts can be created if you have some thin features "
"on the next layer, like letters. Set this setting to 0 to remove these "
"artifacts."
msgstr ""

msgid "Only one wall on first layer"
msgstr ""

msgid ""
"Use only one wall on first layer, to give more space to the bottom infill "
"pattern"
msgstr ""

msgid "Extra perimeters on overhangs"
msgstr ""

msgid ""
"Create additional perimeter paths over steep overhangs and areas where "
"bridges cannot be anchored."
msgstr ""

msgid "Reverse on even"
msgstr ""

msgid "Overhang reversal"
msgstr ""

msgid ""
"Extrude perimeters that have a part over an overhang in the reverse "
"direction on even layers. This alternating pattern can drastically improve "
"steep overhangs.\n"
"\n"
"This setting can also help reduce part warping due to the reduction of "
"stresses in the part walls."
msgstr ""

msgid "Reverse only internal perimeters"
msgstr ""

msgid ""
"Apply the reverse perimeters logic only on internal perimeters.\n"
"\n"
"This setting greatly reduces part stresses as they are now distributed in "
"alternating directions. This should reduce part warping while also "
"maintaining external wall quality. This feature can be very useful for warp "
"prone material, like ABS/ASA, and also for elastic filaments, like TPU and "
"Silk PLA. It can also help reduce warping on floating regions over "
"supports.\n"
"\n"
"For this setting to be the most effective, it is recommended to set the "
"Reverse Threshold to 0 so that all internal walls print in alternating "
"directions on even layers irrespective of their overhang degree."
msgstr ""

msgid "Bridge counterbore holes"
msgstr ""

msgid ""
"This option creates bridges for counterbore holes, allowing them to be "
"printed without support. Available modes include:\n"
"1. None: No bridge is created.\n"
"2. Partially Bridged: Only a part of the unsupported area will be bridged.\n"
"3. Sacrificial Layer: A full sacrificial bridge layer is created."
msgstr ""

msgid "Partially bridged"
msgstr ""

msgid "Sacrificial layer"
msgstr ""

msgid "Reverse threshold"
msgstr ""

msgid "Overhang reversal threshold"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Number of mm the overhang need to be for the reversal to be considered "
"useful. Can be a % of the perimeter width.\n"
"Value 0 enables reversal on every even layers regardless.\n"
"When Detect overhang wall is not enabled, this option is ignored and "
"reversal happens on every even layers regardless."
msgstr ""

msgid "Classic mode"
msgstr ""

msgid "Enable this option to use classic mode"
msgstr ""

msgid "Slow down for overhang"
msgstr "Slow down for overhangs"

msgid "Enable this option to slow printing down for different overhang degree"
msgstr ""
"Enable this option to slow down when printing overhangs. The speeds for "
"different overhang percentages are set below."

msgid "Slow down for curled perimeters"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Enable this option to slow down printing in areas where perimeters may have "
"curled upwards.For example, additional slowdown will be applied when "
"printing overhangs on sharp corners like the front of the Benchy hull, "
"reducing curling which compounds over multiple layers.\n"
"\n"
" It is generally recommended to have this option switched on unless your "
"printer cooling is powerful enough or the print speed slow enough that "
"perimeter curling does not happen. If printing with a high external "
"perimeter speed, this parameter may introduce slight artifacts when slowing "
"down due to the large variance in print speeds. If you notice artifacts, "
"ensure your pressure advance is tuned correctly.\n"
"\n"
"Note: When this option is enabled, overhang perimeters are treated like "
"overhangs, meaning the overhang speed is applied even if the overhanging "
"perimeter is part of a bridge. For example, when the perimeters are 100% "
"overhanging, with no wall supporting them from underneath, the 100% overhang "
"speed will be applied."
msgstr ""

msgid "mm/s or %"
msgstr ""

msgid "External"
msgstr ""

msgid ""
"Speed of the externally visible bridge extrusions.\n"
"\n"
"In addition, if Slow down for curled perimeters is disabled or Classic "
"overhang mode is enabled, it will be the print speed of overhang walls that "
"are supported by less than 13%, whether they are part of a bridge or an "
"overhang."
msgstr ""

msgid "Internal"
msgstr ""

msgid ""
"Speed of internal bridges. If the value is expressed as a percentage, it "
"will be calculated based on the bridge_speed. Default value is 150%."
msgstr ""

msgid "Brim width"
msgstr ""

msgid "Distance from model to the outermost brim line"
msgstr "This is the distance from the model to the outermost brim line."

msgid "Brim type"
msgstr ""

msgid ""
"This controls the generation of the brim at outer and/or inner side of "
"models. Auto means the brim width is analyzed and calculated automatically."
msgstr ""

msgid "Painted"
msgstr ""

msgid "Brim-object gap"
msgstr ""

msgid ""
"A gap between innermost brim line and object can make brim be removed more "
"easily"
msgstr ""
"This creates a gap between the innermost brim line and the object and can "
"make the brim easier to remove."

msgid "Brim ears"
msgstr ""

msgid "Only draw brim over the sharp edges of the model."
msgstr ""

msgid "Brim ear max angle"
msgstr ""

msgid ""
"Maximum angle to let a brim ear appear.\n"
"If set to 0, no brim will be created.\n"
"If set to ~180, brim will be created on everything but straight sections."
msgstr ""

msgid "Brim ear detection radius"
msgstr ""

msgid ""
"The geometry will be decimated before detecting sharp angles. This parameter "
"indicates the minimum length of the deviation for the decimation.\n"
"0 to deactivate"
msgstr ""

msgid "Compatible machine"
msgstr ""

msgid "upward compatible machine"
msgstr ""

msgid "Compatible machine condition"
msgstr ""

msgid ""
"A boolean expression using the configuration values of an active printer "
"profile. If this expression evaluates to true, this profile is considered "
"compatible with the active printer profile."
msgstr ""
"A Boolean expression using the configuration values of an active printer "
"profile. If this expression evaluates to true, this profile is considered "
"compatible with the active printer profile."

msgid "Compatible process profiles"
msgstr ""

msgid "Compatible process profiles condition"
msgstr ""

msgid ""
"A boolean expression using the configuration values of an active print "
"profile. If this expression evaluates to true, this profile is considered "
"compatible with the active print profile."
msgstr ""
"A Boolean expression using the configuration values of an active print "
"profile. If this expression evaluates to true, this profile is considered "
"compatible with the active print profile."

msgid "Print sequence, layer by layer or object by object"
msgstr ""
"This determines the print sequence, allowing you to print layer-by-layer or "
"object-by-object."

msgid "By layer"
msgstr ""

msgid "By object"
msgstr ""

msgid "Intra-layer order"
msgstr ""

msgid "Print order within a single layer"
msgstr ""

msgid "As object list"
msgstr ""

msgid "Slow printing down for better layer cooling"
msgstr ""

msgid ""
"Enable this option to slow printing speed down to make the final layer time "
"not shorter than the layer time threshold in \"Max fan speed threshold\", so "
"that layer can be cooled for longer time. This can improve the cooling "
"quality for needle and small details"
msgstr ""
"Enable this option to slow printing speed down to ensure that the final "
"layer time is not shorter than the layer time threshold in \"Max fan speed "
"threshold\", so that the layer can be cooled for a longer time. This can "
"improve the quality for small details."

msgid "Normal printing"
msgstr ""

msgid ""
"The default acceleration of both normal printing and travel except initial "
"layer"
msgstr ""
"This is the default acceleration for both normal printing and travel after "
"the first layer."

msgid "Default filament profile"
msgstr ""

msgid "Default filament profile when switch to this machine profile"
msgstr "Default filament profile when switching to this machine profile"

msgid "Default process profile"
msgstr ""

msgid "Default process profile when switch to this machine profile"
msgstr "Default process profile when switching to this machine profile"

msgid "Activate air filtration"
msgstr ""

msgid "Activate for better air filtration. G-code command: M106 P3 S(0-255)"
msgstr ""

msgid "Fan speed"
msgstr ""

msgid ""
"Speed of exhaust fan during printing. This speed will override the speed in "
"filament custom G-code."
msgstr ""

msgid "Speed of exhaust fan after printing completes"
msgstr ""

msgid "No cooling for the first"
msgstr ""

msgid ""
"Turn off all cooling fans for the first few layers. This can be used to "
"improve build plate adhesion."
msgstr ""

msgid "Don't support bridges"
msgstr ""

msgid ""
"Don't support the whole bridge area which make support very large. Bridges "
"can usually be printed directly without support if not very long."
msgstr ""
"This disables supporting bridges, which decreases the amount of support "
"required. Bridges can usually be printed directly without support over a "
"reasonable distance."

msgid "Thick external bridges"
msgstr ""

msgid ""
"If enabled, bridges are more reliable, can bridge longer distances, but may "
"look worse. If disabled, bridges look better but are reliable just for "
"shorter bridged distances."
msgstr ""
"If enabled, bridges are more reliable and can bridge longer distances but "
"may look worse. If disabled, bridges look better but are reliable only for "
"shorter distances."

msgid "Thick internal bridges"
msgstr ""

msgid ""
"If enabled, thick internal bridges will be used. It's usually recommended to "
"have this feature turned on. However, consider turning it off if you are "
"using large nozzles."
msgstr ""

msgid "Extra bridge layers (beta)"
msgstr ""

msgid ""
"This option enables the generation of an extra bridge layer over internal "
"and/or external bridges.\n"
"\n"
"Extra bridge layers help improve bridge appearance and reliability, as the "
"solid infill is better supported. This is especially useful in fast "
"printers, where the bridge and solid infill speeds vary greatly. The extra "
"bridge layer results in reduced pillowing on top surfaces, as well as "
"reduced separation of the external bridge layer from its surrounding "
"perimeters.\n"
"\n"
"It is generally recommended to set this to at least 'External bridge only', "
"unless specific issues with the sliced model are found.\n"
"\n"
"Options:\n"
"1. Disabled - does not generate second bridge layers. This is the default "
"and is set for compatibility purposes.\n"
"2. External bridge only - generates second bridge layers for external-facing "
"bridges only. Please note that small bridges that are shorter or narrower "
"than the set number of perimeters will be skipped as they would not benefit "
"from a second bridge layer. If generated, the second bridge layer will be "
"extruded parallel to the first bridge layer to reinforce the bridge "
"strength.\n"
"3. Internal bridge only - generates second bridge layers for internal "
"bridges over sparse infill only. Please note that the internal bridges count "
"towards the top shell layer count of your model. The second internal bridge "
"layer will be extruded as close to perpendicular to the first as possible. "
"If multiple regions in the same island, with varying bridge angles are "
"present, the last region of that island will be selected as the angle "
"reference.\n"
"4. Apply to all - generates second bridge layers for both internal and "
"external-facing bridges\n"
msgstr ""

msgid "Disabled"
msgstr ""

msgid "External bridge only"
msgstr ""

msgid "Internal bridge only"
msgstr ""

msgid "Apply to all"
msgstr ""

msgid "Filter out small internal bridges"
msgstr ""

msgid ""
"This option can help reduce pillowing on top surfaces in heavily slanted or "
"curved models.\n"
"\n"
"By default, small internal bridges are filtered out and the internal solid "
"infill is printed directly over the sparse infill. This works well in most "
"cases, speeding up printing without too much compromise on top surface "
"quality.\n"
"\n"
"However, in heavily slanted or curved models, especially where too low a "
"sparse infill density is used, this may result in curling of the unsupported "
"solid infill, causing pillowing.\n"
"\n"
"Enabling limited filtering or no filtering will print internal bridge layer "
"over slightly unsupported internal solid infill. The options below control "
"the sensitivity of the filtering, i.e. they control where internal bridges "
"are created.\n"
"\n"
"1. Filter - enables this option. This is the default behavior and works well "
"in most cases.\n"
"\n"
"2. Limited filtering - creates internal bridges on heavily slanted surfaces "
"while avoiding unnecessary bridges. This works well for most difficult "
"models.\n"
"\n"
"3. No filtering - creates internal bridges on every potential internal "
"overhang. This option is useful for heavily slanted top surface models; "
"however, in most cases, it creates too many unnecessary bridges."
msgstr ""

msgid "Filter"
msgstr ""

msgid "Limited filtering"
msgstr ""

msgid "No filtering"
msgstr ""

msgid "Max bridge length"
msgstr ""

msgid ""
"Max length of bridges that don't need support. Set it to 0 if you want all "
"bridges to be supported, and set it to a very large value if you don't want "
"any bridges to be supported."
msgstr ""
"This is the maximum length of bridges that don't need support. Set it to 0 "
"if you want all bridges to be supported, and set it to a very large value if "
"you don't want any bridges to be supported."

msgid "End G-code"
msgstr ""

msgid "End G-code when finishing the entire print."
msgstr "Add end G-Code when finishing the entire print."

msgid "Between Object G-code"
msgstr ""

msgid ""
"Insert G-code between objects. This parameter will only come into effect when "
"you print your models object by object."
msgstr ""

msgid "End G-code when finishing the printing of this filament."
msgstr "Add end G-code when finishing the printing of this filament."

msgid "Ensure vertical shell thickness"
msgstr ""

msgid ""
"Add solid infill near sloping surfaces to guarantee the vertical shell "
"thickness (top+bottom solid layers)\n"
"None: No solid infill will be added anywhere. Caution: Use this option "
"carefully if your model has sloped surfaces\n"
"Critical Only: Avoid adding solid infill for walls\n"
"Moderate: Add solid infill for heavily sloping surfaces only\n"
"All: Add solid infill for all suitable sloping surfaces\n"
"Default value is All."
msgstr ""

msgid "Critical Only"
msgstr ""

msgid "Moderate"
msgstr ""

msgid "Top surface pattern"
msgstr ""

msgid "Line pattern of top surface infill"
msgstr "This is the line pattern for top surface infill."

msgid "Concentric"
msgstr ""

msgid "Rectilinear"
msgstr ""

msgid "Monotonic"
msgstr ""

msgid "Monotonic line"
msgstr ""

msgid "Aligned Rectilinear"
msgstr ""

msgid "Hilbert Curve"
msgstr ""

msgid "Archimedean Chords"
msgstr ""

msgid "Octagram Spiral"
msgstr ""

msgid "Bottom surface pattern"
msgstr ""

msgid "Line pattern of bottom surface infill, not bridge infill"
msgstr ""
"This is the line pattern of bottom surface infill, not including bridge "
"infill."

msgid "Internal solid infill pattern"
msgstr ""

msgid ""
"Line pattern of internal solid infill. if the detect narrow internal solid "
"infill be enabled, the concentric pattern will be used for the small area."
msgstr ""

msgid ""
"Line width of outer wall. If expressed as a %, it will be computed over the "
"nozzle diameter."
msgstr ""

msgid ""
"Speed of outer wall which is outermost and visible. It's used to be slower "
"than inner wall speed to get better quality."
msgstr ""
"This is the printing speed for the outer walls of parts. These are generally "
"printed slower than inner walls for higher quality."

msgid "Small perimeters"
msgstr ""

msgid ""
"This separate setting will affect the speed of perimeters having radius <= "
"small_perimeter_threshold (usually holes). If expressed as percentage (for "
"example: 80%) it will be calculated on the outer wall speed setting above. "
"Set to zero for auto."
msgstr ""

msgid "Small perimeters threshold"
msgstr ""

msgid ""
"This sets the threshold for small perimeter length. Default threshold is 0mm"
msgstr ""

msgid "Walls printing order"
msgstr ""

msgid ""
"Print sequence of the internal (inner) and external (outer) walls.\n"
"\n"
"Use Inner/Outer for best overhangs. This is because the overhanging walls "
"can adhere to a neighbouring perimeter while printing. However, this option "
"results in slightly reduced surface quality as the external perimeter is "
"deformed by being squashed to the internal perimeter.\n"
"\n"
"Use Inner/Outer/Inner for the best external surface finish and dimensional "
"accuracy as the external wall is printed undisturbed from an internal "
"perimeter. However, overhang performance will reduce as there is no internal "
"perimeter to print the external wall against. This option requires a minimum "
"of 3 walls to be effective as it prints the internal walls from the 3rd "
"perimeter onwards first, then the external perimeter and, finally, the first "
"internal perimeter. This option is recommended against the Outer/Inner "
"option in most cases.\n"
"\n"
"Use Outer/Inner for the same external wall quality and dimensional accuracy "
"benefits of Inner/Outer/Inner option. However, the z seams will appear less "
"consistent as the first extrusion of a new layer starts on a visible "
"surface.\n"
"\n"
" "
msgstr ""

msgid "Inner/Outer"
msgstr ""

msgid "Outer/Inner"
msgstr ""

msgid "Inner/Outer/Inner"
msgstr ""

msgid "Print infill first"
msgstr ""

msgid ""
"Order of wall/infill. When the tickbox is unchecked the walls are printed "
"first, which works best in most cases.\n"
"\n"
"Printing infill first may help with extreme overhangs as the walls have the "
"neighbouring infill to adhere to. However, the infill will slightly push out "
"the printed walls where it is attached to them, resulting in a worse "
"external surface finish. It can also cause the infill to shine through the "
"external surfaces of the part."
msgstr ""

msgid "Wall loop direction"
msgstr ""

msgid ""
"The direction which the wall loops are extruded when looking down from the "
"top.\n"
"\n"
"By default all walls are extruded in counter-clockwise, unless Reverse on "
"even is enabled. Set this to any option other than Auto will force the wall "
"direction regardless of the Reverse on even.\n"
"\n"
"This option will be disabled if spiral vase mode is enabled."
msgstr ""

msgid "Counter clockwise"
msgstr ""

msgid "Clockwise"
msgstr ""

msgid "Height to rod"
msgstr ""

msgid ""
"Distance of the nozzle tip to the lower rod. Used for collision avoidance in "
"by-object printing."
msgstr ""
"Distance from the nozzle tip to the lower rod. Used for collision avoidance "
"in by-object printing."

msgid "Height to lid"
msgstr ""

msgid ""
"Distance of the nozzle tip to the lid. Used for collision avoidance in by-"
"object printing."
msgstr ""
"Distance from the nozzle tip to the lid. Used for collision avoidance in by-"
"object printing."

msgid ""
"Clearance radius around extruder. Used for collision avoidance in by-object "
"printing."
msgstr ""
"Clearance radius around extruder: used for collision avoidance in by-object "
"printing."

msgid "Nozzle height"
msgstr ""

msgid "The height of nozzle tip."
msgstr ""

msgid "Bed mesh min"
msgstr ""

msgid ""
"This option sets the min point for the allowed bed mesh area. Due to the "
"probe's XY offset, most printers are unable to probe the entire bed. To "
"ensure the probe point does not go outside the bed area, the minimum and "
"maximum points of the bed mesh should be set appropriately. OrcaSlicer "
"ensures that adaptive_bed_mesh_min/adaptive_bed_mesh_max values do not "
"exceed these min/max points. This information can usually be obtained from "
"your printer manufacturer. The default setting is (-99999, -99999), which "
"means there are no limits, thus allowing probing across the entire bed."
msgstr ""

msgid "Bed mesh max"
msgstr ""

msgid ""
"This option sets the max point for the allowed bed mesh area. Due to the "
"probe's XY offset, most printers are unable to probe the entire bed. To "
"ensure the probe point does not go outside the bed area, the minimum and "
"maximum points of the bed mesh should be set appropriately. OrcaSlicer "
"ensures that adaptive_bed_mesh_min/adaptive_bed_mesh_max values do not "
"exceed these min/max points. This information can usually be obtained from "
"your printer manufacturer. The default setting is (99999, 99999), which "
"means there are no limits, thus allowing probing across the entire bed."
msgstr ""

msgid "Probe point distance"
msgstr ""

msgid ""
"This option sets the preferred distance between probe points (grid size) for "
"the X and Y directions, with the default being 50mm for both X and Y."
msgstr ""

msgid "Mesh margin"
msgstr ""

msgid ""
"This option determines the additional distance by which the adaptive bed "
"mesh area should be expanded in the XY directions."
msgstr ""

msgid "Extruder Color"
msgstr ""

msgid "Only used as a visual help on UI"
msgstr ""

msgid "Extruder offset"
msgstr ""

msgid "Flow ratio"
msgstr ""

msgid ""
"The material may have volumetric change after switching between molten and "
"crystalline states. This setting changes all extrusion flow of this filament "
"in G-code proportionally. The recommended value range is between 0.95 and "
"1.05. You may be able to tune this value to get a nice flat surface if there "
"is slight overflow or underflow."
msgstr ""

msgid ""
"The material may have volumetric change after switching between molten and "
"crystalline states. This setting changes all extrusion flow of this filament "
"in G-code proportionally. The recommended value range is between 0.95 and "
"1.05. You may be able to tune this value to get a nice flat surface if there "
"is slight overflow or underflow.\n"
"\n"
"The final object flow ratio is this value multiplied by the filament flow "
"ratio."
msgstr ""

msgid "Enable pressure advance"
msgstr ""

msgid ""
"Enable pressure advance, auto calibration result will be overwritten once "
"enabled."
msgstr ""

msgid "Pressure advance (Klipper) AKA Linear advance factor (Marlin)."
msgstr ""

msgid "Enable adaptive pressure advance (beta)"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"With increasing print speeds (and hence increasing volumetric flow through "
"the nozzle) and increasing accelerations, it has been observed that the "
"effective PA value typically decreases. This means that a single PA value is "
"not always 100% optimal for all features and a compromise value is usually "
"used that does not cause too much bulging on features with lower flow speed "
"and accelerations while also not causing gaps on faster features.\n"
"\n"
"This feature aims to address this limitation by modeling the response of "
"your printer's extrusion system depending on the volumetric flow speed and "
"acceleration it is printing at. Internally, it generates a fitted model that "
"can extrapolate the needed pressure advance for any given volumetric flow "
"speed and acceleration, which is then emitted to the printer depending on "
"the current print conditions.\n"
"\n"
"When enabled, the pressure advance value above is overridden. However, a "
"reasonable default value above is strongly recommended to act as a fallback "
"and for when tool changing.\n"
"\n"
msgstr ""

msgid "Adaptive pressure advance measurements (beta)"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Add sets of pressure advance (PA) values, the volumetric flow speeds and "
"accelerations they were measured at, separated by a comma. One set of values "
"per line. For example\n"
"0.04,3.96,3000\n"
"0.033,3.96,10000\n"
"0.029,7.91,3000\n"
"0.026,7.91,10000\n"
"\n"
"How to calibrate:\n"
"1. Run the pressure advance test for at least 3 speeds per acceleration "
"value. It is recommended that the test is run for at least the speed of the "
"external perimeters, the speed of the internal perimeters and the fastest "
"feature print speed in your profile (usually its the sparse or solid "
"infill). Then run them for the same speeds for the slowest and fastest print "
"accelerations,and no faster than the recommended maximum acceleration as "
"given by the Klipper input shaper.\n"
"2. Take note of the optimal PA value for each volumetric flow speed and "
"acceleration. You can find the flow number by selecting flow from the color "
"scheme drop down and move the horizontal slider over the PA pattern lines. "
"The number should be visible at the bottom of the page. The ideal PA value "
"should be decreasing the higher the volumetric flow is. If it is not, "
"confirm that your extruder is functioning correctly. The slower and with "
"less acceleration you print, the larger the range of acceptable PA values. "
"If no difference is visible, use the PA value from the faster test.\n"
"3. Enter the triplets of PA values, Flow and Accelerations in the text box "
"here and save your filament profile\n"
"\n"
msgstr ""

msgid "Enable adaptive pressure advance for overhangs (beta)"
msgstr ""

msgid ""
"Enable adaptive PA for overhangs as well as when flow changes within the "
"same feature. This is an experimental option, as if the PA profile is not "
"set accurately, it will cause uniformity issues on the external surfaces "
"before and after overhangs.\n"
msgstr ""

msgid "Pressure advance for bridges"
msgstr ""

msgid ""
"Pressure advance value for bridges. Set to 0 to disable.\n"
"\n"
"A lower PA value when printing bridges helps reduce the appearance of "
"slight under extrusion immediately after bridges. This is caused by the "
"pressure drop in the nozzle when printing in the air and a lower PA helps "
"counteract this."
msgstr ""

msgid ""
"Default line width if other line widths are set to 0. If expressed as a %, "
"it will be computed over the nozzle diameter."
msgstr ""

msgid "Keep fan always on"
msgstr ""

msgid ""
"Enabling this setting means that the part cooling fan will never stop "
"completely and will run at least at minimum speed to reduce the frequency of "
"starting and stopping."
msgstr ""
"Enabling this setting means that part cooling fan will never stop entirely "
"and will instead run at least at minimum speed to reduce the frequency of "
"starting and stopping."

msgid "Don't slow down outer walls"
msgstr ""

msgid ""
"If enabled, this setting will ensure external perimeters are not slowed down "
"to meet the minimum layer time. This is particularly helpful in the below "
"scenarios:\n"
"\n"
" 1. To avoid changes in shine when printing glossy filaments \n"
"2. To avoid changes in external wall speed which may create slight wall "
"artifacts that appear like z banding \n"
"3. To avoid printing at speeds which cause VFAs (fine artifacts) on the "
"external walls\n"
"\n"
msgstr ""

msgid "Layer time"
msgstr ""

msgid ""
"Part cooling fan will be enabled for layers of which estimated time is "
"shorter than this value. Fan speed is interpolated between the minimum and "
"maximum fan speeds according to layer printing time"
msgstr ""
"The part cooling fan will be enabled for layers where the estimated time is "
"shorter than this value. Fan speed is interpolated between the minimum and "
"maximum fan speeds according to layer printing time."

msgid "Default color"
msgstr ""

msgid "Default filament color"
msgstr ""

msgid "Filament notes"
msgstr ""

msgid "You can put your notes regarding the filament here."
msgstr ""

msgid "Required nozzle HRC"
msgstr ""

msgid ""
"Minimum HRC of nozzle required to print the filament. Zero means no checking "
"of nozzle's HRC."
msgstr ""
"Minimum HRC of nozzle required to print the filament. A value of 0 means no "
"checking of the nozzle's HRC."

msgid ""
"This setting stands for how much volume of filament can be melted and "
"extruded per second. Printing speed is limited by max volumetric speed, in "
"case of too high and unreasonable speed setting. Can't be zero"
msgstr ""
"This setting is the volume of filament that can be melted and extruded per "
"second. Printing speed is limited by max volumetric speed, in case of too "
"high and unreasonable speed setting. This value cannot be zero."

msgid "mm³/s"
msgstr ""

msgid "Filament load time"
msgstr ""

msgid ""
"Time to load new filament when switch filament. It's usually applicable for "
"single-extruder multi-material machines. For tool changers or multi-tool "
"machines, it's typically 0. For statistics only"
msgstr ""

msgid "Filament unload time"
msgstr ""

msgid ""
"Time to unload old filament when switch filament. It's usually applicable "
"for single-extruder multi-material machines. For tool changers or multi-tool "
"machines, it's typically 0. For statistics only"
msgstr ""

msgid "Tool change time"
msgstr ""

msgid ""
"Time taken to switch tools. It's usually applicable for tool changers or "
"multi-tool machines. For single-extruder multi-material machines, it's "
"typically 0. For statistics only"
msgstr ""

msgid ""
"Filament diameter is used to calculate extrusion in G-code, so it is "
"important and should be accurate."
msgstr ""
"Filament diameter is used to calculate extrusion variables in G-code, so it "
"is important that this is accurate and precise."

msgid "Pellet flow coefficient"
msgstr ""

msgid ""
"Pellet flow coefficient is empirically derived and allows for volume "
"calculation for pellet printers.\n"
"\n"
"Internally it is converted to filament_diameter. All other volume "
"calculations remain the same.\n"
"\n"
"filament_diameter = sqrt( (4 * pellet_flow_coefficient) / PI )"
msgstr ""

msgid "Shrinkage (XY)"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Enter the shrinkage percentage that the filament will get after cooling (94% "
"if you measure 94mm instead of 100mm). The part will be scaled in xy to "
"compensate. Only the filament used for the perimeter is taken into account.\n"
"Be sure to allow enough space between objects, as this compensation is done "
"after the checks."
msgstr ""

msgid "Shrinkage (Z)"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Enter the shrinkage percentage that the filament will get after cooling (94% "
"if you measure 94mm instead of 100mm). The part will be scaled in Z to "
"compensate."
msgstr ""

msgid "Loading speed"
msgstr ""

msgid "Speed used for loading the filament on the wipe tower."
msgstr ""

msgid "Loading speed at the start"
msgstr ""

msgid "Speed used at the very beginning of loading phase."
msgstr ""

msgid "Unloading speed"
msgstr ""

msgid ""
"Speed used for unloading the filament on the wipe tower (does not affect "
"initial part of unloading just after ramming)."
msgstr ""
"Speed used for unloading the filament on the wipe tower (does not affect "
"initial part of unloading just after ramming)."

msgid "Unloading speed at the start"
msgstr ""

msgid ""
"Speed used for unloading the tip of the filament immediately after ramming."
msgstr ""

msgid "Delay after unloading"
msgstr ""

msgid ""
"Time to wait after the filament is unloaded. May help to get reliable tool "
"changes with flexible materials that may need more time to shrink to "
"original dimensions."
msgstr ""

msgid "Number of cooling moves"
msgstr ""

msgid ""
"Filament is cooled by being moved back and forth in the cooling tubes. "
"Specify desired number of these moves."
msgstr ""

msgid "Stamping loading speed"
msgstr ""

msgid "Speed used for stamping."
msgstr ""

msgid "Stamping distance measured from the center of the cooling tube"
msgstr ""

msgid ""
"If set to non-zero value, filament is moved toward the nozzle between the "
"individual cooling moves (\"stamping\"). This option configures how long "
"this movement should be before the filament is retracted again."
msgstr ""

msgid "Speed of the first cooling move"
msgstr ""

msgid "Cooling moves are gradually accelerating beginning at this speed."
msgstr ""

msgid "Minimal purge on wipe tower"
msgstr ""

msgid ""
"After a tool change, the exact position of the newly loaded filament inside "
"the nozzle may not be known, and the filament pressure is likely not yet "
"stable. Before purging the print head into an infill or a sacrificial "
"object, Orca Slicer will always prime this amount of material into the wipe "
"tower to produce successive infill or sacrificial object extrusions reliably."
msgstr ""

msgid "Speed of the last cooling move"
msgstr ""

msgid "Cooling moves are gradually accelerating towards this speed."
msgstr ""

msgid "Ramming parameters"
msgstr ""

msgid ""
"This string is edited by RammingDialog and contains ramming specific "
"parameters."
msgstr ""

msgid "Enable ramming for multi-tool setups"
msgstr ""

msgid ""
"Perform ramming when using multi-tool printer (i.e. when the 'Single "
"Extruder Multimaterial' in Printer Settings is unchecked). When checked, a "
"small amount of filament is rapidly extruded on the wipe tower just before "
"the tool change. This option is only used when the wipe tower is enabled."
msgstr ""

msgid "Multi-tool ramming volume"
msgstr ""

msgid "The volume to be rammed before the tool change."
msgstr ""

msgid "Multi-tool ramming flow"
msgstr ""

msgid "Flow used for ramming the filament before the tool change."
msgstr ""

msgid "Density"
msgstr ""

msgid "Filament density. For statistics only"
msgstr "Filament density, for statistical purposes only."

msgid "g/cm³"
msgstr ""

msgid "The material type of filament"
msgstr "Filament material type"

msgid "Soluble material"
msgstr ""

msgid ""
"Soluble material is commonly used to print support and support interface"
msgstr ""
"Soluble material is commonly used to print support and support interfaces"

msgid "Support material"
msgstr ""

msgid ""
"Support material is commonly used to print support and support interface"
msgstr ""
"Support material is commonly used to print support and support interfaces."

msgid "Softening temperature"
msgstr ""

msgid ""
"The material softens at this temperature, so when the bed temperature is "
"equal to or greater than this, it's highly recommended to open the front "
"door and/or remove the upper glass to avoid clogging."
msgstr ""
"The material softens at this temperature, so when the bed temperature is "
"equal to or greater than this, it's highly recommended to open the front "
"door and/or remove the upper glass to avoid clogs."

msgid "Price"
msgstr ""

msgid "Filament price. For statistics only"
msgstr "Filament price, for statistical purposes only."

msgid "money/kg"
msgstr ""

msgid "Vendor"
msgstr ""

msgid "Vendor of filament. For show only"
msgstr ""

msgid "(Undefined)"
msgstr ""

msgid "Sparse infill direction"
msgstr ""

msgid ""
"Angle for sparse infill pattern, which controls the start or main direction "
"of line"
msgstr ""
"This is the angle for sparse infill pattern, which controls the start or "
"main direction of lines."

msgid "Solid infill direction"
msgstr ""

msgid ""
"Angle for solid infill pattern, which controls the start or main direction "
"of line"
msgstr ""

msgid "Rotate solid infill direction"
msgstr ""

msgid "Rotate the solid infill direction by 90° for each layer."
msgstr ""

msgid "Sparse infill density"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Density of internal sparse infill, 100% turns all sparse infill into solid "
"infill and internal solid infill pattern will be used"
msgstr ""

msgid "Sparse infill pattern"
msgstr ""

msgid "Line pattern for internal sparse infill"
msgstr "This is the line pattern for internal sparse infill."

msgid "Grid"
msgstr ""

msgid "2D Lattice"
msgstr ""

msgid "Line"
msgstr ""

msgid "Cubic"
msgstr ""

msgid "Tri-hexagon"
msgstr ""

msgid "Gyroid"
msgstr ""

msgid "Honeycomb"
msgstr ""

msgid "Adaptive Cubic"
msgstr ""

msgid "3D Honeycomb"
msgstr ""

msgid "Support Cubic"
msgstr ""

msgid "Lightning"
msgstr ""

msgid "Cross Hatch"
msgstr ""

msgid "Quarter Cubic"
msgstr ""

msgid "Lattice angle 1"
msgstr ""

msgid ""
"The angle of the first set of 2D lattice elements in the Z direction. Zero "
"is vertical."
msgstr ""

msgid "Lattice angle 2"
msgstr ""

msgid ""
"The angle of the second set of 2D lattice elements in the Z direction. Zero "
"is vertical."
msgstr ""

msgid "Sparse infill anchor length"
msgstr ""

msgid ""
"Connect an infill line to an internal perimeter with a short segment of an "
"additional perimeter. If expressed as percentage (example: 15%) it is "
"calculated over infill extrusion width. Orca Slicer tries to connect two "
"close infill lines to a short perimeter segment. If no such perimeter "
"segment shorter than infill_anchor_max is found, the infill line is "
"connected to a perimeter segment at just one side and the length of the "
"perimeter segment taken is limited to this parameter, but no longer than "
"anchor_length_max.\n"
"Set this parameter to zero to disable anchoring perimeters connected to a "
"single infill line."
msgstr ""

msgid "0 (no open anchors)"
msgstr ""

msgid "1000 (unlimited)"
msgstr ""

msgid "Maximum length of the infill anchor"
msgstr ""

msgid ""
"Connect an infill line to an internal perimeter with a short segment of an "
"additional perimeter. If expressed as percentage (example: 15%) it is "
"calculated over infill extrusion width. Orca Slicer tries to connect two "
"close infill lines to a short perimeter segment. If no such perimeter "
"segment shorter than this parameter is found, the infill line is connected "
"to a perimeter segment at just one side and the length of the perimeter "
"segment taken is limited to infill_anchor, but no longer than this "
"parameter.\n"
"If set to 0, the old algorithm for infill connection will be used, it should "
"create the same result as with 1000 & 0."
msgstr ""

msgid "0 (Simple connect)"
msgstr ""

msgid "Acceleration of outer walls"
msgstr ""

msgid "Acceleration of inner walls"
msgstr ""

msgid "Acceleration of travel moves"
msgstr ""

msgid ""
"Acceleration of top surface infill. Using a lower value may improve top "
"surface quality"
msgstr ""
"This is the acceleration of top surface infill. Using a lower value may "
"improve top surface quality."

msgid "Acceleration of outer wall. Using a lower value can improve quality"
msgstr "Acceleration of outer wall: using a lower value can improve quality."

msgid ""
"Acceleration of bridges. If the value is expressed as a percentage (e.g. "
"50%), it will be calculated based on the outer wall acceleration."
msgstr ""

msgid "mm/s² or %"
msgstr ""

msgid ""
"Acceleration of sparse infill. If the value is expressed as a percentage "
"(e.g. 100%), it will be calculated based on the default acceleration."
msgstr ""

msgid ""
"Acceleration of internal solid infill. If the value is expressed as a "
"percentage (e.g. 100%), it will be calculated based on the default "
"acceleration."
msgstr ""

msgid ""
"Acceleration of initial layer. Using a lower value can improve build plate "
"adhesion."
msgstr ""
"This is the printing acceleration for the first layer. Using limited "
"acceleration can improve build plate adhesion."

msgid "Enable accel_to_decel"
msgstr ""

msgid "Klipper's max_accel_to_decel will be adjusted automatically"
msgstr ""

msgid "accel_to_decel"
msgstr ""

#, c-format, boost-format
msgid ""
"Klipper's max_accel_to_decel will be adjusted to this %% of acceleration"
msgstr ""

msgid "Jerk of outer walls"
msgstr ""

msgid "Jerk of inner walls"
msgstr ""

msgid "Jerk for top surface"
msgstr ""

msgid "Jerk for infill"
msgstr ""

msgid "Jerk for initial layer"
msgstr ""

msgid "Jerk for travel"
msgstr ""

msgid ""
"Line width of initial layer. If expressed as a %, it will be computed over "
"the nozzle diameter."
msgstr ""

msgid "Initial layer height"
msgstr "First layer height"

msgid ""
"Height of initial layer. Making initial layer height to be thick slightly "
"can improve build plate adhesion"
msgstr ""
"This is the height of the first layer. Making the first layer height thicker "
"can improve build plate adhesion."

msgid "Speed of initial layer except the solid infill part"
msgstr ""
"This is the speed for the first layer except for solid infill sections."

msgid "Initial layer infill"
msgstr "First layer infill"

msgid "Speed of solid infill part of initial layer"
msgstr "This is the speed for solid infill parts of the first layer."

msgid "Initial layer travel speed"
msgstr ""

msgid "Travel speed of initial layer"
msgstr ""

#, fuzzy
msgid "Number of slow layers"
msgstr "This is the number of top interface layers."

msgid ""
"The first few layers are printed slower than normal. The speed is gradually "
"increased in a linear fashion over the specified number of layers."
msgstr ""

msgid "Initial layer nozzle temperature"
msgstr "First layer nozzle temperature"

msgid "Nozzle temperature for printing initial layer when using this filament"
msgstr "Nozzle temperature for printing the first layer with this filament"

msgid "Full fan speed at layer"
msgstr ""

msgid ""
"Fan speed will be ramped up linearly from zero at layer "
"\"close_fan_the_first_x_layers\" to maximum at layer "
"\"full_fan_speed_layer\". \"full_fan_speed_layer\" will be ignored if lower "
"than \"close_fan_the_first_x_layers\", in which case the fan will be running "
"at maximum allowed speed at layer \"close_fan_the_first_x_layers\" + 1."
msgstr ""

msgid "layer"
msgstr ""

msgid "Support interface fan speed"
msgstr ""

msgid ""
"This part cooling fan speed is applied when printing support interfaces. "
"Setting this parameter to a higher than regular speed reduces the layer "
"binding strength between supports and the supported part, making them easier "
"to separate.\n"
"Set to -1 to disable it.\n"
"This setting is overridden by disable_fan_first_layers."
msgstr ""

msgid "Internal bridges fan speed"
msgstr ""

msgid ""
"The part cooling fan speed used for all internal bridges. Set to -1 to use "
"the overhang fan speed settings instead.\n"
"\n"
"Reducing the internal bridges fan speed, compared to your regular fan speed, "
"can help reduce part warping due to excessive cooling applied over a large "
"surface for a prolonged period of time."
msgstr ""

msgid ""
"Randomly jitter while printing the wall, so that the surface has a rough "
"look. This setting controls the fuzzy position"
msgstr ""
"This setting makes the toolhead randomly jitter while printing walls so that "
"the surface has a rough textured look. This setting controls the fuzzy "
"position."

msgid "Contour"
msgstr ""

msgid "Contour and hole"
msgstr ""

msgid "All walls"
msgstr ""

msgid "Fuzzy skin thickness"
msgstr ""

msgid ""
"The width within which to jitter. It's advised to be below outer wall line "
"width"
msgstr ""
"The width of jittering: it’s recommended to keep this lower than the outer "
"wall line width."

msgid "Fuzzy skin point distance"
msgstr ""

msgid ""
"The average distance between the random points introduced on each line "
"segment"
msgstr ""

msgid "Apply fuzzy skin to first layer"
msgstr ""

msgid "Whether to apply fuzzy skin on the first layer"
msgstr ""

msgid "Fuzzy skin noise type"
msgstr ""

msgid ""
"Noise type to use for fuzzy skin generation.\n"
"Classic: Classic uniform random noise.\n"
"Perlin: Perlin noise, which gives a more consistent texture.\n"
"Billow: Similar to perlin noise, but clumpier.\n"
"Ridged Multifractal: Ridged noise with sharp, jagged features. Creates "
"marble-like textures.\n"
"Voronoi: Divides the surface into voronoi cells, and displaces each one by a "
"random amount. Creates a patchwork texture."
msgstr ""

msgid "Classic"
msgstr ""

msgid "Perlin"
msgstr ""

msgid "Billow"
msgstr ""

msgid "Ridged Multifractal"
msgstr ""

msgid "Voronoi"
msgstr ""

msgid "Fuzzy skin feature size"
msgstr ""

msgid ""
"The base size of the coherent noise features, in mm. Higher values will "
"result in larger features."
msgstr ""

msgid "Fuzzy Skin Noise Octaves"
msgstr ""

msgid ""
"The number of octaves of coherent noise to use. Higher values increase the "
"detail of the noise, but also increase computation time."
msgstr ""

msgid "Fuzzy skin noise persistence"
msgstr ""

msgid ""
"The decay rate for higher octaves of the coherent noise. Lower values will "
"result in smoother noise."
msgstr ""

msgid "Filter out tiny gaps"
msgstr ""

msgid "Layers and Perimeters"
msgstr ""

msgid ""
"Don't print gap fill with a length is smaller than the threshold specified "
"(in mm). This setting applies to top, bottom and solid infill and, if using "
"the classic perimeter generator, to wall gap fill."
msgstr ""

msgid ""
"Speed of gap infill. Gap usually has irregular line width and should be "
"printed more slowly"
msgstr ""
"This is the speed for gap infill. Gaps usually have irregular line width and "
"should be printed more slowly."

msgid "Precise Z height"
msgstr ""

msgid ""
"Enable this to get precise z height of object after slicing. It will get the "
"precise object height by fine-tuning the layer heights of the last few "
"layers. Note that this is an experimental parameter."
msgstr ""

msgid "Arc fitting"
msgstr ""

msgid ""
"Enable this to get a G-code file which has G2 and G3 moves. The fitting "
"tolerance is same as the resolution.\n"
"\n"
"Note: For Klipper machines, this option is recommended to be disabled. "
"Klipper does not benefit from arc commands as these are split again into "
"line segments by the firmware. This results in a reduction in surface "
"quality as line segments are converted to arcs by the slicer and then back "
"to line segments by the firmware."
msgstr ""

msgid "Add line number"
msgstr ""

msgid ""
"Enable this to add line number(Nx) at the beginning of each G-code line."
msgstr ""

msgid "Scan first layer"
msgstr ""

msgid ""
"Enable this to enable the camera on printer to check the quality of first "
"layer"
msgstr ""
"Enable this to allow the camera on the printer to check the quality of the "
"first layer."

msgid "Nozzle type"
msgstr ""

msgid ""
"The metallic material of nozzle. This determines the abrasive resistance of "
"nozzle, and what kind of filament can be printed"
msgstr ""
"The metallic material of the nozzle: This determines the abrasive resistance "
"of the nozzle and what kind of filament can be printed."

msgid "Undefine"
msgstr "Undefined"

msgid "Hardened steel"
msgstr ""

msgid "Stainless steel"
msgstr ""

msgid "Brass"
msgstr ""

msgid "Nozzle HRC"
msgstr ""

msgid ""
"The nozzle's hardness. Zero means no checking for nozzle's hardness during "
"slicing."
msgstr ""
"The nozzle's hardness. Zero means no checking for nozzle hardness during "
"slicing."

msgid "HRC"
msgstr ""

msgid "Printer structure"
msgstr ""

msgid "The physical arrangement and components of a printing device"
msgstr ""

msgid "CoreXY"
msgstr ""

msgid "I3"
msgstr ""

msgid "Hbot"
msgstr ""

msgid "Delta"
msgstr ""

msgid "Best object position"
msgstr ""

msgid "Best auto arranging position in range [0,1] w.r.t. bed shape."
msgstr ""

msgid ""
"Enable this option if machine has auxiliary part cooling fan. G-code "
"command: M106 P2 S(0-255)."
msgstr ""

msgid ""
"Start the fan this number of seconds earlier than its target start time (you "
"can use fractional seconds). It assumes infinite acceleration for this time "
"estimation, and will only take into account G1 and G0 moves (arc fitting is "
"unsupported).\n"
"It won't move fan commands from custom G-code (they act as a sort of "
"'barrier').\n"
"It won't move fan commands into the start G-code if the 'only custom start "
"G-code' is activated.\n"
"Use 0 to deactivate."
msgstr ""

msgid "Only overhangs"
msgstr ""

msgid "Will only take into account the delay for the cooling of overhangs."
msgstr ""

msgid "Fan kick-start time"
msgstr ""

msgid ""
"Emit a max fan speed command for this amount of seconds before reducing to "
"target speed to kick-start the cooling fan.\n"
"This is useful for fans where a low PWM/power may be insufficient to get the "
"fan started spinning from a stop, or to get the fan up to speed faster.\n"
"Set to 0 to deactivate."
msgstr ""

msgid "Time cost"
msgstr ""

msgid "The printer cost per hour"
msgstr ""

msgid "money/h"
msgstr ""

msgid "Support control chamber temperature"
msgstr "Support controlling chamber temperature"

msgid ""
"This option is enabled if machine support controlling chamber temperature\n"
"G-code command: M141 S(0-255)"
msgstr ""

msgid "Support air filtration"
msgstr ""

msgid ""
"Enable this if printer support air filtration\n"
"G-code command: M106 P3 S(0-255)"
msgstr ""

msgid "G-code flavor"
msgstr ""

msgid "What kind of G-code the printer is compatible with."
msgstr ""

msgid "Klipper"
msgstr ""

msgid "Pellet Modded Printer"
msgstr ""

msgid "Enable this option if your printer uses pellets instead of filaments"
msgstr ""

msgid "Support multi bed types"
msgstr ""

msgid "Enable this option if you want to use multiple bed types"
msgstr ""

msgid "Label objects"
msgstr ""

msgid ""
"Enable this to add comments into the G-code labeling print moves with what "
"object they belong to, which is useful for the Octoprint CancelObject "
"plugin. This settings is NOT compatible with Single Extruder Multi Material "
"setup and Wipe into Object / Wipe into Infill."
msgstr ""

msgid "Exclude objects"
msgstr ""

msgid "Enable this option to add EXCLUDE OBJECT command in G-code."
msgstr ""

msgid "Verbose G-code"
msgstr ""

msgid ""
"Enable this to get a commented G-code file, with each line explained by a "
"descriptive text. If you print from SD card, the additional weight of the "
"file could make your firmware slow down."
msgstr ""

msgid "Infill combination"
msgstr ""

msgid ""
"Automatically Combine sparse infill of several layers to print together to "
"reduce time. Wall is still printed with original layer height."
msgstr ""
"Automatically combine sparse infill of several layers to print together in "
"order to reduce time. Walls are still printed with original layer height."

msgid "Infill combination - Max layer height"
msgstr ""

msgid ""
"Maximum layer height for the combined sparse infill.\n"
"\n"
"Set it to 0 or 100% to use the nozzle diameter (for maximum reduction in "
"print time) or a value of ~80% to maximize sparse infill strength.\n"
"\n"
"The number of layers over which infill is combined is derived by dividing "
"this value with the layer height and rounded down to the nearest decimal.\n"
"\n"
"Use either absolute mm values (eg. 0.32mm for a 0.4mm nozzle) or % values "
"(eg 80%). This value must not be larger than the nozzle diameter."
msgstr ""

msgid "Filament to print internal sparse infill."
msgstr "This is the filament for printing internal sparse infill."

msgid ""
"Line width of internal sparse infill. If expressed as a %, it will be "
"computed over the nozzle diameter."
msgstr ""

msgid "Infill/Wall overlap"
msgstr "Infill/wall overlap"

#, no-c-format, no-boost-format
msgid ""
"Infill area is enlarged slightly to overlap with wall for better bonding. "
"The percentage value is relative to line width of sparse infill. Set this "
"value to ~10-15% to minimize potential over extrusion and accumulation of "
"material resulting in rough top surfaces."
msgstr ""
"This allows the infill area to be enlarged slightly to overlap with walls "
"for better bonding. The percentage value is relative to line width of "
"sparse infill. Set this value to ~10-15% to minimize potential over "
"extrusion and accumulation of material resulting in rough top surfaces."

msgid "Top/Bottom solid infill/wall overlap"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Top solid infill area is enlarged slightly to overlap with wall for better "
"bonding and to minimize the appearance of pinholes where the top infill "
"meets the walls. A value of 25-30% is a good starting point, minimizing the "
"appearance of pinholes. The percentage value is relative to line width of "
"sparse infill"
msgstr ""

msgid "Speed of internal sparse infill"
msgstr "This is the speed for internal sparse infill."

msgid "Inherits profile"
msgstr ""

msgid "Name of parent profile"
msgstr ""

msgid "Interface shells"
msgstr ""

msgid ""
"Force the generation of solid shells between adjacent materials/volumes. "
"Useful for multi-extruder prints with translucent materials or manual "
"soluble support material"
msgstr ""

msgid "Maximum width of a segmented region"
msgstr ""

msgid "Maximum width of a segmented region. Zero disables this feature."
msgstr ""
"Maximum width of a segmented region. A value of 0 disables this feature."

msgid "Interlocking depth of a segmented region"
msgstr ""

msgid ""
"Interlocking depth of a segmented region. It will be ignored if "
"\"mmu_segmented_region_max_width\" is zero or if "
"\"mmu_segmented_region_interlocking_depth\" is bigger than "
"\"mmu_segmented_region_max_width\". Zero disables this feature."
msgstr ""

msgid "Use beam interlocking"
msgstr ""

msgid ""
"Generate interlocking beam structure at the locations where different "
"filaments touch. This improves the adhesion between filaments, especially "
"models printed in different materials."
msgstr ""

msgid "Interlocking beam width"
msgstr ""

msgid "The width of the interlocking structure beams."
msgstr ""

msgid "Interlocking direction"
msgstr ""

msgid "Orientation of interlock beams."
msgstr ""

msgid "Interlocking beam layers"
msgstr ""

msgid ""
"The height of the beams of the interlocking structure, measured in number of "
"layers. Less layers is stronger, but more prone to defects."
msgstr ""

msgid "Interlocking depth"
msgstr ""

msgid ""
"The distance from the boundary between filaments to generate interlocking "
"structure, measured in cells. Too few cells will result in poor adhesion."
msgstr ""

msgid "Interlocking boundary avoidance"
msgstr ""

msgid ""
"The distance from the outside of a model where interlocking structures will "
"not be generated, measured in cells."
msgstr ""

msgid "Ironing Type"
msgstr "Ironing type"

msgid ""
"Ironing is using small flow to print on same height of surface again to make "
"flat surface more smooth. This setting controls which layer being ironed"
msgstr ""
"Ironing uses a small flow to print at the same height of a surface to make "
"flat surfaces smoother. This setting controls which layers are being ironed."

msgid "No ironing"
msgstr ""

msgid "Top surfaces"
msgstr "All top surfaces"

msgid "Topmost surface"
msgstr "Topmost surface only"

msgid "All solid layer"
msgstr "All solid layers"

msgid "Ironing Pattern"
msgstr ""

msgid "The pattern that will be used when ironing"
msgstr ""

msgid "Ironing flow"
msgstr ""

msgid ""
"The amount of material to extrude during ironing. Relative to flow of normal "
"layer height. Too high value results in overextrusion on the surface"
msgstr ""
"This is the amount of material to be extruded during ironing. It is relative "
"to the flow of normal layer height. Too high a value will result in "
"overextrusion on the surface."

msgid "Ironing line spacing"
msgstr ""

msgid "The distance between the lines of ironing"
msgstr "This is the distance between the lines used for ironing."

msgid "Ironing inset"
msgstr ""

msgid ""
"The distance to keep from the edges. A value of 0 sets this to half of the "
"nozzle diameter"
msgstr ""

msgid "Ironing speed"
msgstr ""

msgid "Print speed of ironing lines"
msgstr "This is the print speed for ironing lines."

msgid "Ironing angle"
msgstr ""

msgid ""
"The angle ironing is done at. A negative number disables this function and "
"uses the default method."
msgstr ""

msgid "This G-code is inserted at every layer change after the Z lift."
msgstr ""

msgid "Supports silent mode"
msgstr "Silent Mode"

msgid ""
"Whether the machine supports silent mode in which machine use lower "
"acceleration to print"
msgstr ""
"Whether the machine supports silent mode in which machine uses lower "
"acceleration to print more quietly"

msgid "Emit limits to G-code"
msgstr ""

msgid "Machine limits"
msgstr ""

msgid ""
"If enabled, the machine limits will be emitted to G-code file.\n"
"This option will be ignored if the G-code flavor is set to Klipper."
msgstr ""

msgid ""
"This G-code will be used as a code for the pause print. Users can insert "
"pause G-code in the G-code viewer."
msgstr ""

msgid "This G-code will be used as a custom code"
msgstr ""

msgid "Small area flow compensation (beta)"
msgstr ""

msgid "Enable flow compensation for small infill areas"
msgstr ""

msgid "Flow Compensation Model"
msgstr ""

msgid ""
"Flow Compensation Model, used to adjust the flow for small infill areas. The "
"model is expressed as a comma separated pair of values for extrusion length "
"and flow correction factors, one per line, in the following format: "
"\"1.234,5.678\""
msgstr ""

msgid "Maximum speed X"
msgstr ""

msgid "Maximum speed Y"
msgstr ""

msgid "Maximum speed Z"
msgstr ""

msgid "Maximum speed E"
msgstr ""

msgid "Maximum X speed"
msgstr ""

msgid "Maximum Y speed"
msgstr ""

msgid "Maximum Z speed"
msgstr ""

msgid "Maximum E speed"
msgstr ""

msgid "Maximum acceleration X"
msgstr ""

msgid "Maximum acceleration Y"
msgstr ""

msgid "Maximum acceleration Z"
msgstr ""

msgid "Maximum acceleration E"
msgstr ""

msgid "Maximum acceleration of the X axis"
msgstr ""

msgid "Maximum acceleration of the Y axis"
msgstr ""

msgid "Maximum acceleration of the Z axis"
msgstr ""

msgid "Maximum acceleration of the E axis"
msgstr ""

msgid "Maximum jerk X"
msgstr ""

msgid "Maximum jerk Y"
msgstr ""

msgid "Maximum jerk Z"
msgstr ""

msgid "Maximum jerk E"
msgstr ""

msgid "Maximum jerk of the X axis"
msgstr ""

msgid "Maximum jerk of the Y axis"
msgstr ""

msgid "Maximum jerk of the Z axis"
msgstr ""

msgid "Maximum jerk of the E axis"
msgstr ""

msgid "Minimum speed for extruding"
msgstr ""

msgid "Minimum speed for extruding (M205 S)"
msgstr ""

msgid "Minimum travel speed"
msgstr ""

msgid "Minimum travel speed (M205 T)"
msgstr ""

msgid "Maximum acceleration for extruding"
msgstr ""

msgid "Maximum acceleration for extruding (M204 P)"
msgstr ""

msgid "Maximum acceleration for retracting"
msgstr ""

msgid "Maximum acceleration for retracting (M204 R)"
msgstr ""

msgid "Maximum acceleration for travel"
msgstr ""

msgid "Maximum acceleration for travel (M204 T), it only applies to Marlin 2"
msgstr ""

msgid ""
"Part cooling fan speed may be increased when auto cooling is enabled. This "
"is the maximum speed for the part cooling fan."
msgstr ""
"The part cooling fan speed may be increased when auto cooling is enabled. "
"This is the maximum speed for the part cooling fan."

msgid "Max"
msgstr ""

msgid ""
"The highest printable layer height for the extruder. Used to limit the "
"maximum layer height when adaptive layer height is enabled."
msgstr ""
"The highest printable layer height for the extruder. This is used to limit "
"the maximum layer height when adaptive layer height is enabled."

msgid "Extrusion rate smoothing"
msgstr ""

msgid ""
"This parameter smooths out sudden extrusion rate changes that happen when "
"the printer transitions from printing a high flow (high speed/larger width) "
"extrusion to a lower flow (lower speed/smaller width) extrusion and vice "
"versa.\n"
"\n"
"It defines the maximum rate by which the extruded volumetric flow in mm3/sec "
"can change over time. Higher values mean higher extrusion rate changes are "
"allowed, resulting in faster speed transitions.\n"
"\n"
"A value of 0 disables the feature.\n"
"\n"
"For a high speed, high flow direct drive printer (like the Bambu lab or "
"Voron) this value is usually not needed. However it can provide some "
"marginal benefit in certain cases where feature speeds vary greatly. For "
"example, when there are aggressive slowdowns due to overhangs. In these "
"cases a high value of around 300-350mm3/s2 is recommended as this allows "
"for just enough smoothing to assist pressure advance achieve a smoother flow "
"transition.\n"
"\n"
"For slower printers without pressure advance, the value should be set much "
"lower. A value of 10-15mm3/s2 is a good starting point for direct drive "
"extruders and 5-10mm3/s2 for Bowden style.\n"
"\n"
"This feature is known as Pressure Equalizer in Prusa slicer.\n"
"\n"
"Note: this parameter disables arc fitting."
msgstr ""

msgid "mm³/s²"
msgstr ""

msgid "Smoothing segment length"
msgstr ""

msgid ""
"A lower value results in smoother extrusion rate transitions. However, this "
"results in a significantly larger G-code file and more instructions for the "
"printer to process.\n"
"\n"
"Default value of 3 works well for most cases. If your printer is stuttering, "
"increase this value to reduce the number of adjustments made.\n"
"\n"
"Allowed values: 0.5-5"
msgstr ""

msgid "Apply only on external features"
msgstr ""

msgid ""
"Applies extrusion rate smoothing only on external perimeters and overhangs. "
"This can help reduce artefacts due to sharp speed transitions on externally "
"visible overhangs without impacting the print speed of features that will "
"not be visible to the user."
msgstr ""

msgid "Minimum speed for part cooling fan"
msgstr ""

msgid ""
"Speed of auxiliary part cooling fan. Auxiliary fan will run at this speed "
"during printing except the first several layers which is defined by no "
"cooling layers.\n"
"Please enable auxiliary_fan in printer settings to use this feature. G-code "
"command: M106 P2 S(0-255)"
msgstr ""

msgid "Min"
msgstr ""

msgid ""
"The lowest printable layer height for the extruder. Used to limit the "
"minimum layer height when adaptive layer height is enabled."
msgstr ""
"The lowest printable layer height for the extruder. This is used to limit "
"the minimum layer height when adaptive layer height is enabled."

msgid "Min print speed"
msgstr ""

msgid ""
"The minimum print speed to which the printer slows down to maintain the "
"minimum layer time defined above when the slowdown for better layer cooling "
"is enabled."
msgstr ""

msgid "Diameter of nozzle"
msgstr "The diameter of the nozzle"

msgid "Configuration notes"
msgstr ""

msgid ""
"You can put here your personal notes. This text will be added to the G-code "
"header comments."
msgstr ""

msgid "Host Type"
msgstr ""

msgid ""
"Orca Slicer can upload G-code files to a printer host. This field must "
"contain the kind of the host."
msgstr ""

msgid "Nozzle volume"
msgstr ""

msgid "Volume of nozzle between the cutter and the end of nozzle"
msgstr "Volume of nozzle between the filament cutter and the end of the nozzle"

msgid "Cooling tube position"
msgstr ""

msgid "Distance of the center-point of the cooling tube from the extruder tip."
msgstr ""

msgid "Cooling tube length"
msgstr ""

msgid "Length of the cooling tube to limit space for cooling moves inside it."
msgstr ""

msgid "High extruder current on filament swap"
msgstr ""

msgid ""
"It may be beneficial to increase the extruder motor current during the "
"filament exchange sequence to allow for rapid ramming feed rates and to "
"overcome resistance when loading a filament with an ugly shaped tip."
msgstr ""

msgid "Filament parking position"
msgstr ""

msgid ""
"Distance of the extruder tip from the position where the filament is parked "
"when unloaded. This should match the value in printer firmware."
msgstr ""

msgid "Extra loading distance"
msgstr ""

msgid ""
"When set to zero, the distance the filament is moved from parking position "
"during load is exactly the same as it was moved back during unload. When "
"positive, it is loaded further, if negative, the loading move is shorter "
"than unloading."
msgstr ""

msgid "Start end points"
msgstr ""

msgid "The start and end points which is from cutter area to garbage can."
msgstr ""
"The start and end points which are from the cutter area to the excess chute."

msgid "Reduce infill retraction"
msgstr ""

msgid ""
"Don't retract when the travel is in infill area absolutely. That means the "
"oozing can't been seen. This can reduce times of retraction for complex "
"model and save printing time, but make slicing and G-code generating slower"
msgstr ""
"Don't retract when the travel is entirely in an infill area. That means the "
"oozing can't been seen. This can reduce times of retraction for complex "
"model and save printing time, but make slicing and G-code generation slower."

msgid ""
"This option will drop the temperature of the inactive extruders to prevent "
"oozing."
msgstr ""

msgid "Filename format"
msgstr ""

msgid "Users can define the project file name when exporting."
msgstr "Users can decide project file names when exporting."

msgid "Make overhangs printable"
msgstr ""

msgid "Modify the geometry to print overhangs without support material."
msgstr ""

msgid "Make overhangs printable - Maximum angle"
msgstr ""

msgid ""
"Maximum angle of overhangs to allow after making more steep overhangs "
"printable.90° will not change the model at all and allow any overhang, while "
"0 will replace all overhangs with conical material."
msgstr ""

msgid "Make overhangs printable - Hole area"
msgstr ""

msgid ""
"Maximum area of a hole in the base of the model before it's filled by "
"conical material. A value of 0 will fill all the holes in the model base."
msgstr ""

msgid "mm²"
msgstr ""

msgid "Detect overhang wall"
msgstr "Detect overhang walls"

#, c-format, boost-format
msgid ""
"Detect the overhang percentage relative to line width and use different "
"speed to print. For 100%% overhang, bridge speed is used."
msgstr ""
"This detects the overhang percentage relative to line width and uses a "
"different speed to print. For 100%% overhang, bridging speed is used."

msgid "Filament to print walls"
msgstr ""

msgid ""
"Line width of inner wall. If expressed as a %, it will be computed over the "
"nozzle diameter."
msgstr ""

msgid "Speed of inner wall"
msgstr "This is the speed for inner walls."

msgid "Number of walls of every layer"
msgstr "This is the number of walls per layer."

msgid "Alternate extra wall"
msgstr ""

msgid ""
"This setting adds an extra wall to every other layer. This way the infill "
"gets wedged vertically between the walls, resulting in stronger prints.\n"
"\n"
"When this option is enabled, the ensure vertical shell thickness option "
"needs to be disabled.\n"
"\n"
"Using lightning infill together with this option is not recommended as there "
"is limited infill to anchor the extra perimeters to."
msgstr ""

msgid ""
"If you want to process the output G-code through custom scripts, just list "
"their absolute paths here. Separate multiple scripts with a semicolon. "
"Scripts will be passed the absolute path to the G-code file as the first "
"argument, and they can access the Orca Slicer config settings by reading "
"environment variables."
msgstr ""

msgid "Printer type"
msgstr ""

msgid "Type of the printer"
msgstr ""

msgid "Printer notes"
msgstr ""

msgid "You can put your notes regarding the printer here."
msgstr ""

msgid "Printer variant"
msgstr ""

msgid "Raft contact Z distance"
msgstr ""

msgid "Z gap between object and raft. Ignored for soluble interface"
msgstr ""
"This is the Z gap between an object and a raft. It is ignored for soluble "
"interfaces."

msgid "Raft expansion"
msgstr ""

msgid "Expand all raft layers in XY plane"
msgstr "This expands all raft layers in XY plane."

msgid "Initial layer density"
msgstr "First layer density"

msgid "Density of the first raft or support layer"
msgstr "This is the density of the first raft or support layer."

msgid "Initial layer expansion"
msgstr "First layer expansion"

msgid "Expand the first raft or support layer to improve bed plate adhesion"
msgstr "This expands the first raft or support layer to improve bed adhesion."

msgid "Raft layers"
msgstr ""

msgid ""
"Object will be raised by this number of support layers. Use this function to "
"avoid warping when printing ABS."
msgstr ""

msgid ""
"The G-code path is generated after simplifying the contour of models to "
"avoid too many points and G-code lines. Smaller value means higher "
"resolution and more time to slice."
msgstr ""
"The G-code path is generated after simplifying the contour of models to "
"avoid too many points and G-code lines. Smaller values mean higher "
"resolution and more time required to slice."

msgid "Travel distance threshold"
msgstr ""

msgid ""
"Only trigger retraction when the travel distance is longer than this "
"threshold"
msgstr ""
"Only trigger retraction when the travel distance is longer than this "
"threshold."

msgid "Retract amount before wipe"
msgstr ""

msgid ""
"The length of fast retraction before wipe, relative to retraction length"
msgstr ""
"This is the length of fast retraction before a wipe, relative to retraction "
"length."

msgid "Retract when change layer"
msgstr "Retract on layer change"

msgid "Force a retraction when changes layer"
msgstr "This forces a retraction on layer changes."

msgid "Retract on top layer"
msgstr ""

msgid ""
"Force a retraction on top layer. Disabling could prevent clog on very slow "
"patterns with small movements, like Hilbert curve"
msgstr ""

msgid "Retraction Length"
msgstr ""

msgid ""
"Some amount of material in extruder is pulled back to avoid ooze during long "
"travel. Set zero to disable retraction"
msgstr ""
"This is the amount of filament in the extruder that is pulled back to avoid "
"oozing during long travel distances. Set to 0 to disable retraction."

msgid "Long retraction when cut (beta)"
msgstr "Long retraction when cut (beta)"

msgid ""
"Experimental feature: Retracting and cutting off the filament at a longer "
"distance during changes to minimize purge. While this reduces flush "
"significantly, it may also raise the risk of nozzle clogs or other printing "
"problems."
msgstr ""

msgid "Retraction distance when cut"
msgstr ""

msgid ""
"Experimental feature: Retraction length before cutting off during filament "
"change."
msgstr ""

msgid "Z-hop height"
msgstr ""

msgid ""
"Whenever the retraction is done, the nozzle is lifted a little to create "
"clearance between nozzle and the print. It prevents nozzle from hitting the "
"print when travel move. Using spiral lines to lift Z can prevent stringing."
msgstr ""
"Whenever there is a retraction, the nozzle is lifted a little to create "
"clearance between the nozzle and the print. This prevents the nozzle from "
"hitting the print when traveling more. Using spiral lines to lift z can "
"prevent stringing."

msgid "Z-hop lower boundary"
msgstr ""

msgid ""
"Z-hop will only come into effect when Z is above this value and is below the "
"parameter: \"Z-hop upper boundary\"."
msgstr ""

msgid "Z-hop upper boundary"
msgstr ""

msgid ""
"If this value is positive, Z-hop will only come into effect when Z is above "
"the parameter: \"Z-hop lower boundary\" and is below this value."
msgstr ""

msgid "Z-hop type"
msgstr ""

msgid "Slope"
msgstr ""

msgid "Spiral"
msgstr ""

msgid "Traveling angle"
msgstr ""

msgid ""
"Traveling angle for Slope and Spiral Z-hop type. Setting it to 90° results "
"in Normal Lift."
msgstr ""

msgid "Only lift Z above"
msgstr ""

msgid ""
"If you set this to a positive value, Z lift will only take place above the "
"specified absolute Z."
msgstr ""

msgid "Only lift Z below"
msgstr ""

msgid ""
"If you set this to a positive value, Z lift will only take place below the "
"specified absolute Z."
msgstr ""

msgid "On surfaces"
msgstr ""

msgid ""
"Enforce Z-Hop behavior. This setting is impacted by the above settings (Only "
"lift Z above/below)."
msgstr ""

msgid "All Surfaces"
msgstr ""

msgid "Top Only"
msgstr ""

msgid "Bottom Only"
msgstr ""

msgid "Top and Bottom"
msgstr ""

msgid "Extra length on restart"
msgstr ""

msgid ""
"When the retraction is compensated after the travel move, the extruder will "
"push this additional amount of filament. This setting is rarely needed."
msgstr ""

msgid ""
"When the retraction is compensated after changing tool, the extruder will "
"push this additional amount of filament."
msgstr ""

msgid "Retraction Speed"
msgstr "Retraction speed"

msgid "Speed of retractions"
msgstr "This is the speed for retraction."

msgid "De-retraction Speed"
msgstr "Deretraction speed"

msgid ""
"Speed for reloading filament into extruder. Zero means same speed with "
"retraction"
msgstr ""
"The speed for reloading filament into the extruder after a retraction; "
"setting this to 0 means that it will be the same speed as the retraction."

msgid "Use firmware retraction"
msgstr ""

msgid ""
"This experimental setting uses G10 and G11 commands to have the firmware "
"handle the retraction. This is only supported in recent Marlin."
msgstr ""

msgid "Show auto-calibration marks"
msgstr ""

msgid "Disable set remaining print time"
msgstr ""

msgid ""
"Disable generating of the M73: Set remaining print time in the final G-code."
msgstr ""

msgid "Seam position"
msgstr ""

msgid "The start position to print each part of outer wall"
msgstr "This is the starting position for each part of the outer wall."

msgid "Nearest"
msgstr ""

msgid "Aligned"
msgstr ""

msgid "Back"
msgstr ""

msgid "Random"
msgstr ""

msgid "Staggered inner seams"
msgstr ""

msgid ""
"This option causes the inner seams to be shifted backwards based on their "
"depth, forming a zigzag pattern."
msgstr ""

msgid "Seam gap"
msgstr ""

msgid ""
"In order to reduce the visibility of the seam in a closed loop extrusion, "
"the loop is interrupted and shortened by a specified amount.\n"
"This amount can be specified in millimeters or as a percentage of the "
"current extruder diameter. The default value for this parameter is 10%."
msgstr ""

msgid "Scarf joint seam (beta)"
msgstr ""

msgid "Use scarf joint to minimize seam visibility and increase seam strength."
msgstr ""

msgid "Conditional scarf joint"
msgstr ""

msgid ""
"Apply scarf joints only to smooth perimeters where traditional seams do not "
"conceal the seams at sharp corners effectively."
msgstr ""

msgid "Conditional angle threshold"
msgstr ""

msgid ""
"This option sets the threshold angle for applying a conditional scarf joint "
"seam.\n"
"If the maximum angle within the perimeter loop exceeds this value "
"(indicating the absence of sharp corners), a scarf joint seam will be used. "
"The default value is 155°."
msgstr ""

msgid "Conditional overhang threshold"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"This option determines the overhang threshold for the application of scarf "
"joint seams. If the unsupported portion of the perimeter is less than this "
"threshold, scarf joint seams will be applied. The default threshold is set "
"at 40% of the external wall's width. Due to performance considerations, the "
"degree of overhang is estimated."
msgstr ""

msgid "Scarf joint speed"
msgstr ""

msgid ""
"This option sets the printing speed for scarf joints. It is recommended to "
"print scarf joints at a slow speed (less than 100 mm/s). It's also "
"advisable to enable 'Extrusion rate smoothing' if the set speed varies "
"significantly from the speed of the outer or inner walls. If the speed "
"specified here is higher than the speed of the outer or inner walls, the "
"printer will default to the slower of the two speeds. When specified as a "
"percentage (e.g., 80%), the speed is calculated based on the respective "
"outer or inner wall speed. The default value is set to 100%."
msgstr ""

msgid "Scarf joint flow ratio"
msgstr ""

msgid "This factor affects the amount of material for scarf joints."
msgstr ""

msgid "Scarf start height"
msgstr ""

msgid ""
"Start height of the scarf.\n"
"This amount can be specified in millimeters or as a percentage of the "
"current layer height. The default value for this parameter is 0."
msgstr ""

msgid "Scarf around entire wall"
msgstr ""

msgid "The scarf extends to the entire length of the wall."
msgstr ""

msgid "Scarf length"
msgstr ""

msgid ""
"Length of the scarf. Setting this parameter to zero effectively disables the "
"scarf."
msgstr ""

msgid "Scarf steps"
msgstr ""

msgid "Minimum number of segments of each scarf."
msgstr ""

msgid "Scarf joint for inner walls"
msgstr ""

msgid "Use scarf joint for inner walls as well."
msgstr ""

msgid "Role base wipe speed"
msgstr ""

msgid ""
"The wipe speed is determined by the speed of the current extrusion role. e.g. "
"if a wipe action is executed immediately following an outer wall extrusion, "
"the speed of the outer wall extrusion will be utilized for the wipe action."
msgstr ""

msgid "Wipe on loops"
msgstr ""

msgid ""
"To minimize the visibility of the seam in a closed loop extrusion, a small "
"inward movement is executed before the extruder leaves the loop."
msgstr ""

msgid "Wipe before external loop"
msgstr ""

msgid ""
"To minimize visibility of potential overextrusion at the start of an "
"external perimeter when printing with Outer/Inner or Inner/Outer/Inner wall "
"print order, the de-retraction is performed slightly on the inside from the "
"start of the external perimeter. That way any potential over extrusion is "
"hidden from the outside surface.\n"
"\n"
"This is useful when printing with Outer/Inner or Inner/Outer/Inner wall "
"print order as in these modes it is more likely an external perimeter is "
"printed immediately after a de-retraction move."
msgstr ""

msgid "Wipe speed"
msgstr ""

msgid ""
"The wipe speed is determined by the speed setting specified in this "
"configuration. If the value is expressed as a percentage (e.g. 80%), it will "
"be calculated based on the travel speed setting above. The default value for "
"this parameter is 80%."
msgstr ""

msgid "Skirt distance"
msgstr ""

msgid "Distance from skirt to brim or object"
msgstr "This is the distance from the skirt to the brim or the object."

msgid "Skirt start point"
msgstr ""

msgid ""
"Angle from the object center to skirt start point. Zero is the most right "
"position, counter clockwise is positive angle."
msgstr ""

msgid "Skirt height"
msgstr ""

msgid "How many layers of skirt. Usually only one layer"
msgstr "Number of skirt layers: usually only one"

msgid "Single loop draft shield"
msgstr ""

msgid ""
"Limits the draft shield loops to one wall after the first layer. This is "
"useful, on occasion, to conserve filament but may cause the draft shield to "
"warp / crack."
msgstr ""

msgid "Draft shield"
msgstr ""

msgid ""
"A draft shield is useful to protect an ABS or ASA print from warping and "
"detaching from print bed due to wind draft. It is usually needed only with "
"open frame printers, i.e. without an enclosure.\n"
"\n"
"Enabled = skirt is as tall as the highest printed object. Otherwise 'Skirt "
"height' is used.\n"
"Note: With the draft shield active, the skirt will be printed at skirt "
"distance from the object. Therefore, if brims are active it may intersect "
"with them. To avoid this, increase the skirt distance value.\n"
msgstr ""

msgid "Enabled"
msgstr ""

msgid "Skirt type"
msgstr ""

msgid ""
"Combined - single skirt for all objects, Per object - individual object "
"skirt."
msgstr ""

msgid "Combined"
msgstr ""

msgid "Per object"
msgstr ""

msgid "Skirt loops"
msgstr ""

msgid "Number of loops for the skirt. Zero means disabling skirt"
msgstr ""
"This is the number of loops for the skirt. 0 means the skirt is disabled."

msgid "Skirt speed"
msgstr ""

msgid "Speed of skirt, in mm/s. Zero means use default layer extrusion speed."
msgstr ""

msgid "Skirt minimum extrusion length"
msgstr ""

msgid ""
"Minimum filament extrusion length in mm when printing the skirt. Zero means "
"this feature is disabled.\n"
"\n"
"Using a non-zero value is useful if the printer is set up to print without a "
"prime line.\n"
"Final number of loops is not taking into account while arranging or "
"validating objects distance. Increase loop number in such case."
msgstr ""

msgid ""
"The printing speed in exported G-code will be slowed down when the estimated "
"layer time is shorter than this value in order to get better cooling for "
"these layers."
msgstr ""

msgid "Minimum sparse infill threshold"
msgstr ""

msgid ""
"Sparse infill area which is smaller than threshold value is replaced by "
"internal solid infill"
msgstr ""
"Sparse infill areas which are smaller than this threshold value are replaced "
"by internal solid infill."

msgid "Solid infill"
msgstr ""

msgid "Filament to print solid infill"
msgstr ""

msgid ""
"Line width of internal solid infill. If expressed as a %, it will be "
"computed over the nozzle diameter."
msgstr ""

msgid "Speed of internal solid infill, not the top and bottom surface"
msgstr ""
"This is the speed for internal solid infill, not including the top or bottom "
"surface."

msgid ""
"Spiralize smooths out the z moves of the outer contour. And turns a solid "
"model into a single walled print with solid bottom layers. The final "
"generated model has no seam"
msgstr ""
"This enables spiraling, which smooths out the Z moves of the outer contour "
"and turns a solid model into a single walled print with solid bottom layers. "
"The final generated model has no seam."

msgid "Smooth Spiral"
msgstr ""

msgid ""
"Smooth Spiral smooths out X and Y moves as well, resulting in no visible "
"seam at all, even in the XY directions on walls that are not vertical"
msgstr ""

msgid "Max XY Smoothing"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Maximum distance to move points in XY to try to achieve a smooth spiral. If "
"expressed as a %, it will be computed over nozzle diameter"
msgstr ""

msgid "Spiral starting flow ratio"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Sets the starting flow ratio while transitioning from the last bottom layer "
"to the spiral. Normally the spiral transition scales the flow ratio from 0% "
"to 100% during the first loop which can in some cases lead to under "
"extrusion at the start of the spiral."
msgstr ""

msgid "Spiral finishing flow ratio"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Sets the finishing flow ratio while ending the spiral. Normally the spiral "
"transition scales the flow ratio from 100% to 0% during the last loop which "
"can in some cases lead to under extrusion at the end of the spiral."
msgstr ""

msgid ""
"If smooth or traditional mode is selected, a timelapse video will be "
"generated for each print. After each layer is printed, a snapshot is taken "
"with the chamber camera. All of these snapshots are composed into a "
"timelapse video when printing completes. If smooth mode is selected, the "
"toolhead will move to the excess chute after each layer is printed and then "
"take a snapshot. Since the melt filament may leak from the nozzle during the "
"process of taking a snapshot, prime tower is required for smooth mode to wipe "
"nozzle."
msgstr ""
"If smooth or traditional mode is selected, a timelapse video will be "
"generated for each print. After each layer is printed, a snapshot is taken "
"with the chamber camera. All of these snapshots are composed into a "
"timelapse video when printing completes. If smooth mode is selected, the "
"toolhead will move to the excess chute after each layer is printed and then "
"take a snapshot. Since the melt filament may leak from the nozzle during the "
"process of taking a snapshot, a prime tower is required for smooth mode to "
"wipe the nozzle."

msgid "Traditional"
msgstr ""

msgid "Temperature variation"
msgstr ""

#. TRN PrintSettings : "Ooze prevention" > "Temperature variation"
msgid ""
"Temperature difference to be applied when an extruder is not active. The "
"value is not used when 'idle_temperature' in filament settings is set to "
"non-zero value."
msgstr ""

msgid "Preheat time"
msgstr ""

msgid ""
"To reduce the waiting time after tool change, Orca can preheat the next tool "
"while the current tool is still in use. This setting specifies the time in "
"seconds to preheat the next tool. Orca will insert a M104 command to preheat "
"the tool in advance."
msgstr ""

msgid "Preheat steps"
msgstr ""

msgid ""
"Insert multiple preheat commands (e.g. M104.1). Only useful for Prusa XL. For "
"other printers, please set it to 1."
msgstr ""

msgid "Start G-code"
msgstr ""

msgid "Start G-code when starting the entire print."
msgstr "G-code added when starting a print."

msgid "Start G-code when starting the printing of this filament."
msgstr "G-code added when the printer starts using this filament"

msgid "Single Extruder Multi Material"
msgstr ""

msgid "Use single nozzle to print multi filament"
msgstr ""

msgid "Manual Filament Change"
msgstr ""

msgid ""
"Enable this option to omit the custom Change filament G-code only at the "
"beginning of the print. The tool change command (e.g., T0) will be skipped "
"throughout the entire print. This is useful for manual multi-material "
"printing, where we use M600/PAUSE to trigger the manual filament change "
"action."
msgstr ""

msgid "Purge in prime tower"
msgstr ""

msgid "Purge remaining filament into prime tower"
msgstr ""

msgid "Enable filament ramming"
msgstr ""

msgid "No sparse layers (beta)"
msgstr ""

msgid ""
"If enabled, the wipe tower will not be printed on layers with no tool "
"changes. On layers with a tool change, extruder will travel downward to "
"print the wipe tower. User is responsible for ensuring there is no collision "
"with the print."
msgstr ""

msgid "Prime all printing extruders"
msgstr ""

msgid ""
"If enabled, all printing extruders will be primed at the front edge of the "
"print bed at the start of the print."
msgstr ""

msgid "Slice gap closing radius"
msgstr ""

msgid ""
"Cracks smaller than 2x gap closing radius are being filled during the "
"triangle mesh slicing. The gap closing operation may reduce the final print "
"resolution, therefore it is advisable to keep the value reasonably low."
msgstr ""

msgid "Slicing Mode"
msgstr ""

msgid ""
"Use \"Even-odd\" for 3DLabPrint airplane models. Use \"Close holes\" to "
"close all holes in the model."
msgstr ""

msgid "Regular"
msgstr ""

msgid "Even-odd"
msgstr ""

msgid "Close holes"
msgstr ""

msgid "Z offset"
msgstr ""

msgid ""
"This value will be added (or subtracted) from all the Z coordinates in the "
"output G-code. It is used to compensate for bad Z endstop position: for "
"example, if your endstop zero actually leaves the nozzle 0.3mm far from the "
"print bed, set this to -0.3 (or fix your endstop)."
msgstr ""

msgid "Enable support"
msgstr ""

msgid "Enable support generation."
msgstr "This enables support generation."

msgid ""
"Normal (auto) and Tree (auto) are used to generate support automatically. If "
"Normal (manual) or Tree (manual) is selected, only support enforcers are "
"generated."
msgstr ""

msgid "Normal (auto)"
msgstr ""

msgid "Tree (auto)"
msgstr ""

msgid "Normal (manual)"
msgstr ""

msgid "Tree (manual)"
msgstr ""

msgid "Support/object xy distance"
msgstr ""

msgid "XY separation between an object and its support"
msgstr "This controls the XY separation between an object and its support."

msgid "Support/object first layer gap"
msgstr ""

msgid "XY separation between an object and its support at the first layer."
msgstr ""

msgid "Pattern angle"
msgstr ""

msgid "Use this setting to rotate the support pattern on the horizontal plane."
msgstr ""

msgid "On build plate only"
msgstr ""

msgid "Don't create support on model surface, only on build plate"
msgstr "This setting only generates supports that begin on the build plate."

msgid "Support critical regions only"
msgstr ""

msgid ""
"Only create support for critical regions including sharp tail, cantilever, "
"etc."
msgstr ""

msgid "Remove small overhangs"
msgstr ""

msgid "Remove small overhangs that possibly need no supports."
msgstr ""

msgid "Top Z distance"
msgstr ""

msgid "The z gap between the top support interface and object"
msgstr "This determines the Z gap between top support interfaces and objects."

msgid "Bottom Z distance"
msgstr ""

msgid "The z gap between the bottom support interface and object"
msgstr ""

msgid "Support/raft base"
msgstr ""

msgid ""
"Filament to print support base and raft. \"Default\" means no specific "
"filament for support and current filament is used"
msgstr ""
"Filament to print support bases and rafts. \"Default\" means no specific "
"filament for support, and current filament is used"

msgid "Avoid interface filament for base"
msgstr ""

msgid ""
"Avoid using support interface filament to print support base if possible."
msgstr ""

msgid ""
"Line width of support. If expressed as a %, it will be computed over the "
"nozzle diameter."
msgstr ""

msgid "Interface use loop pattern"
msgstr "Loop pattern interface"

msgid ""
"Cover the top contact layer of the supports with loops. Disabled by default."
msgstr ""
"This covers the top contact layer of the supports with loops. It is disabled "
"by default."

msgid "Support/raft interface"
msgstr ""

msgid ""
"Filament to print support interface. \"Default\" means no specific filament "
"for support interface and current filament is used"
msgstr ""
"Filament to print support interfaces. \"Default\" means no specific filament "
"for support interface, and current filament is used"

msgid "Top interface layers"
msgstr ""

msgid "Number of top interface layers"
msgstr "This is the number of top interface layers."

msgid "Bottom interface layers"
msgstr ""

msgid "Number of bottom interface layers"
msgstr ""

msgid "Same as top"
msgstr ""

msgid "Top interface spacing"
msgstr ""

msgid "Spacing of interface lines. Zero means solid interface"
msgstr "This is the spacing of interface lines. 0 means solid interface."

msgid "Bottom interface spacing"
msgstr ""

msgid "Spacing of bottom interface lines. Zero means solid interface"
msgstr ""
"This is the spacing of bottom interface lines. 0 means solid interface."

msgid "Speed of support interface"
msgstr "This is the speed for support interfaces."

msgid "Base pattern"
msgstr ""

msgid "Line pattern of support"
msgstr "This is the line pattern for support."

msgid "Rectilinear grid"
msgstr ""

msgid "Hollow"
msgstr ""

msgid "Interface pattern"
msgstr ""

msgid ""
"Line pattern of support interface. Default pattern for non-soluble support "
"interface is Rectilinear, while default pattern for soluble support "
"interface is Concentric"
msgstr ""
"This is the line pattern for support interfaces. The default pattern for non-"
"soluble support interfaces is Rectilinear while the default pattern for "
"soluble support interfaces is Concentric."

msgid "Rectilinear Interlaced"
msgstr ""

msgid "Base pattern spacing"
msgstr ""

msgid "Spacing between support lines"
msgstr "This determines the spacing between support lines."

msgid "Normal Support expansion"
msgstr "Normal support expansion"

msgid "Expand (+) or shrink (-) the horizontal span of normal support"
msgstr ""

msgid "Speed of support"
msgstr "This is the speed for support."

msgid ""
"Style and shape of the support. For normal support, projecting the supports "
"into a regular grid will create more stable supports (default), while snug "
"support towers will save material and reduce object scarring.\n"
"For tree support, slim and organic style will merge branches more "
"aggressively and save a lot of material (default organic), while hybrid "
"style will create similar structure to normal support under large flat "
"overhangs."
msgstr ""

msgid "Default (Grid/Organic)"
msgstr ""

msgid "Snug"
msgstr ""

msgid "Organic"
msgstr ""

msgid "Tree Slim"
msgstr ""

msgid "Tree Strong"
msgstr ""

msgid "Tree Hybrid"
msgstr ""

msgid "Independent support layer height"
msgstr ""

msgid ""
"Support layer uses layer height independent with object layer. This is to "
"support customizing z-gap and save print time. This option will be invalid "
"when the prime tower is enabled."
msgstr ""

msgid "Threshold angle"
msgstr ""

msgid ""
"Support will be generated for overhangs whose slope angle is below the "
"threshold."
msgstr ""
"Support will be generated for overhangs whose slope angle is below this "
"threshold."

msgid "Threshold overlap"
msgstr ""

msgid ""
"If threshold angle is zero, support will be generated for overhangs whose "
"overlap is below the threshold. The smaller this value is, the steeper the "
"overhang that can be printed without support."
msgstr ""

msgid "Tree support branch angle"
msgstr ""

msgid ""
"This setting determines the maximum overhang angle that the branches of tree "
"support are allowed to make. If the angle is increased, the branches can be "
"printed more horizontally, allowing them to reach farther."
msgstr ""

msgid "Preferred Branch Angle"
msgstr ""

#. TRN PrintSettings: "Organic supports" > "Preferred Branch Angle"
msgid ""
"The preferred angle of the branches, when they do not have to avoid the "
"model. Use a lower angle to make them more vertical and more stable. Use a "
"higher angle for branches to merge faster."
msgstr ""

msgid "Tree support branch distance"
msgstr ""

msgid ""
"This setting determines the distance between neighboring tree support nodes."
msgstr ""

msgid "Branch Density"
msgstr ""

#. TRN PrintSettings: "Organic supports" > "Branch Density"
msgid ""
"Adjusts the density of the support structure used to generate the tips of "
"the branches. A higher value results in better overhangs but the supports "
"are harder to remove, thus it is recommended to enable top support "
"interfaces instead of a high branch density value if dense interfaces are "
"needed."
msgstr ""

msgid "Adaptive layer height"
msgstr ""

msgid ""
"Enabling this option means the height of tree support layer except the "
"first will be automatically calculated "
msgstr ""

msgid "Auto brim width"
msgstr ""

msgid ""
"Enabling this option means the width of the brim for tree support will be "
"automatically calculated"
msgstr ""

msgid "Tree support brim width"
msgstr ""

msgid "Distance from tree branch to the outermost brim line"
msgstr ""

msgid "Tip Diameter"
msgstr ""

#. TRN PrintSettings: "Organic supports" > "Tip Diameter"
msgid "Branch tip diameter for organic supports."
msgstr ""

msgid "Tree support branch diameter"
msgstr ""

msgid "This setting determines the initial diameter of support nodes."
msgstr ""

#. TRN PrintSettings: #lmFIXME
msgid "Branch Diameter Angle"
msgstr ""

#. TRN PrintSettings: "Organic supports" > "Branch Diameter Angle"
msgid ""
"The angle of the branches' diameter as they gradually become thicker towards "
"the bottom. An angle of 0 will cause the branches to have uniform thickness "
"over their length. A bit of an angle can increase stability of the organic "
"support."
msgstr ""

msgid "Support wall loops"
msgstr ""

msgid ""
"This setting specifies the count of support walls in the range of [0,2]. 0 "
"means auto."
msgstr ""

msgid "Tree support with infill"
msgstr ""

msgid ""
"This setting specifies whether to add infill inside large hollows of tree "
"support"
msgstr ""
"This setting specifies whether to add infill inside large hollows of tree "
"support."

msgid "Activate temperature control"
msgstr ""

msgid ""
"Enable this option for automated chamber temperature control. This option "
"activates the emitting of an M191 command before the "
"\"machine_start_gcode\"\n"
" which sets the chamber temperature and waits until it is reached. In "
"addition, it emits an M141 command at the end of the print to turn off the "
"chamber heater, if present.\n"
"\n"
"This option relies on the firmware supporting the M191 and M141 commands "
"either via macros or natively and is usually used when an active chamber "
"heater is installed."
msgstr ""

msgid "Chamber temperature"
msgstr ""

msgid ""
"For high-temperature materials like ABS, ASA, PC, and PA, a higher chamber "
"temperature can help suppress or reduce warping and potentially lead to "
"higher interlayer bonding strength. However, at the same time, a higher "
"chamber temperature will reduce the efficiency of air filtration for ABS and "
"ASA.\n"
"\n"
"For PLA, PETG, TPU, PVA, and other low-temperature materials, this option "
"should be disabled (set to 0) as the chamber temperature should be low to "
"avoid extruder clogging caused by material softening at the heat break.\n"
"\n"
"If enabled, this parameter also sets a G-code variable named "
"chamber_temperature, which can be used to pass the desired chamber "
"temperature to your print start macro, or a heat soak macro like this: "
"PRINT_START (other variables) CHAMBER_TEMP=[chamber_temperature]. This may "
"be useful if your printer does not support M141/M191 commands, or if you "
"desire to handle heat soaking in the print start macro if no active chamber "
"heater is installed."
msgstr ""

msgid "Nozzle temperature for layers after the initial one"
msgstr "Nozzle temperature after the first layer"

msgid "Detect thin wall"
msgstr "Detect thin walls"

msgid ""
"Detect thin wall which can't contain two line width. And use single line to "
"print. Maybe printed not very well, because it's not closed loop"
msgstr ""
"This detects thin walls which can’t contain two lines and uses a single line "
"to print. It may not print as well because it’s not a closed loop."

msgid ""
"This G-code is inserted when filament is changed, including T commands to "
"trigger tool change."
msgstr ""

msgid "This G-code is inserted when the extrusion role is changed."
msgstr ""

msgid ""
"Line width for top surfaces. If expressed as a %, it will be computed over "
"the nozzle diameter."
msgstr ""

msgid "Speed of top surface infill which is solid"
msgstr "This is the speed for solid top surface infill."

msgid "Top shell layers"
msgstr ""

msgid ""
"This is the number of solid layers of top shell, including the top surface "
"layer. When the thickness calculated by this value is thinner than top shell "
"thickness, the top shell layers will be increased"
msgstr ""
"This is the number of solid layers of top shell, including the top surface "
"layer. When the thickness calculated by this value is thinner than the top "
"shell thickness, the top shell layers will be increased"

msgid "Top solid layers"
msgstr ""

msgid "Top shell thickness"
msgstr ""

msgid ""
"The number of top solid layers is increased when slicing if the thickness "
"calculated by top shell layers is thinner than this value. This can avoid "
"having too thin shell when layer height is small. 0 means that this setting "
"is disabled and thickness of top shell is absolutely determined by top shell "
"layers"
msgstr ""
"The number of top solid layers is increased when slicing if the thickness "
"calculated by top shell layers is thinner than this value. This can avoid "
"having too thin a shell when layer height is small. 0 means that this "
"setting is disabled and thickness of top shell is determined simply by the "
"number of top shell layers."

msgid "Speed of travel which is faster and without extrusion"
msgstr "This is the speed at which traveling is done."

msgid "Wipe while retracting"
msgstr ""

msgid ""
"Move nozzle along the last extrusion path when retracting to clean any "
"leaked material on the nozzle. This can minimize blobs when printing a new "
"part after traveling."
msgstr ""
"This moves the nozzle along the last extrusion path when retracting to clean "
"any leaked material on the nozzle. This can minimize blobs when printing a "
"new part after traveling."

msgid "Wipe Distance"
msgstr "Wipe distance"

msgid ""
"Describe how long the nozzle will move along the last path when "
"retracting.\n"
"\n"
"Depending on how long the wipe operation lasts, how fast and long the "
"extruder/filament retraction settings are, a retraction move may be needed "
"to retract the remaining filament.\n"
"\n"
"Setting a value in the retract amount before wipe setting below will perform "
"any excess retraction before the wipe, else it will be performed after."
msgstr ""

msgid ""
"The wiping tower can be used to clean up the residue on the nozzle and "
"stabilize the chamber pressure inside the nozzle, in order to avoid "
"appearance defects when printing objects."
msgstr ""
"The wiping tower can be used to clean up residue on the nozzle and stabilize "
"the chamber pressure inside the nozzle in order to avoid appearance defects "
"when printing objects."

msgid "Purging volumes"
msgstr ""

msgid "Flush multiplier"
msgstr ""

msgid ""
"The actual flushing volumes is equal to the flush multiplier multiplied by "
"the flushing volumes in the table."
msgstr ""
"The actual flushing volumes is equal to the flush multiplier value "
"multiplied by the flushing volumes in the table."

msgid "Prime volume"
msgstr ""

msgid "The volume of material to prime extruder on tower."
msgstr ""
"This is the volume of material to prime the extruder with on the tower."

msgid "Width of prime tower"
msgstr "This is the width of prime towers."

msgid "Wipe tower rotation angle"
msgstr ""

msgid "Wipe tower rotation angle with respect to x-axis."
msgstr ""

msgid "Stabilization cone apex angle"
msgstr ""

msgid ""
"Angle at the apex of the cone that is used to stabilize the wipe tower. "
"Larger angle means wider base."
msgstr ""

msgid "Maximum wipe tower print speed"
msgstr ""

msgid ""
"The maximum print speed when purging in the wipe tower and printing the wipe "
"tower sparse layers. When purging, if the sparse infill speed or calculated "
"speed from the filament max volumetric speed is lower, the lowest will be "
"used instead.\n"
"\n"
"When printing the sparse layers, if the internal perimeter speed or "
"calculated speed from the filament max volumetric speed is lower, the lowest "
"will be used instead.\n"
"\n"
"Increasing this speed may affect the tower's stability as well as increase "
"the force with which the nozzle collides with any blobs that may have formed "
"on the wipe tower.\n"
"\n"
"Before increasing this parameter beyond the default of 90mm/sec, make sure "
"your printer can reliably bridge at the increased speeds and that ooze when "
"tool changing is well controlled.\n"
"\n"
"For the wipe tower external perimeters the internal perimeter speed is used "
"regardless of this setting."
msgstr ""

msgid ""
"The extruder to use when printing perimeter of the wipe tower. Set to 0 to "
"use the one that is available (non-soluble would be preferred)."
msgstr ""

msgid "Purging volumes - load/unload volumes"
msgstr ""

msgid ""
"This vector saves required volumes to change from/to each tool used on the "
"wipe tower. These values are used to simplify creation of the full purging "
"volumes below."
msgstr ""

msgid ""
"Purging after filament change will be done inside objects' infills. This may "
"lower the amount of waste and decrease the print time. If the walls are "
"printed with transparent filament, the mixed color infill will be seen "
"outside. It will not take effect, unless the prime tower is enabled."
msgstr ""
"Purging after filament change will be done inside objects' infills. This may "
"lower the amount of waste and decrease the print time. If the walls are "
"printed with transparent filament, the mixed color infill will be visible. "
"It will not take effect unless the prime tower is enabled."

msgid ""
"Purging after filament change will be done inside objects' support. This may "
"lower the amount of waste and decrease the print time. It will not take "
"effect, unless the prime tower is enabled."
msgstr ""
"Purging after filament change will be done inside objects' support. This may "
"lower the amount of waste and decrease the print time. It will not take "
"effect unless a prime tower is enabled."

msgid ""
"This object will be used to purge the nozzle after a filament change to save "
"filament and decrease the print time. Colors of the objects will be mixed as "
"a result. It will not take effect unless the prime tower is enabled."
msgstr ""

msgid "Maximal bridging distance"
msgstr ""

msgid "Maximal distance between supports on sparse infill sections."
msgstr ""

msgid "Wipe tower purge lines spacing"
msgstr ""

msgid "Spacing of purge lines on the wipe tower."
msgstr ""

msgid "Extra flow for purging"
msgstr ""

msgid ""
"Extra flow used for the purging lines on the wipe tower. This makes the "
"purging lines thicker or narrower than they normally would be. The spacing "
"is adjusted automatically."
msgstr ""

msgid "Idle temperature"
msgstr ""

msgid ""
"Nozzle temperature when the tool is currently not used in multi-tool setups. "
"This is only used when 'Ooze prevention' is active in Print Settings. Set to "
"0 to disable."
msgstr ""

msgid "X-Y hole compensation"
msgstr ""

msgid ""
"Holes in objects will expand or contract in the XY plane by the configured "
"value. Positive values make holes bigger, negative values make holes "
"smaller. This function is used to adjust sizes slightly when the objects "
"have assembling issues."
msgstr ""
"Holes in objects will expand or contract in the XY plane by the set value. "
"Positive values make holes bigger and negative values make holes smaller. "
"This function is used to adjust sizes slightly when objects have assembly "
"issues."

msgid "X-Y contour compensation"
msgstr ""

msgid ""
"Contours of objects will expand or contract in the XY plane by the "
"configured value. Positive values make contours bigger, negative values make "
"contours smaller. This function is used to adjust sizes slightly when the "
"objects have assembling issues."
msgstr ""
"Contours of objects will expand or contract in the XY plane by the set "
"value. Positive values make contours bigger and negative values make "
"contours smaller. This function is used to adjust sizes slightly when "
"objects have assembly issues."

msgid "Convert holes to polyholes"
msgstr ""

msgid ""
"Search for almost-circular holes that span more than one layer and convert "
"the geometry to polyholes. Use the nozzle size and the (biggest) diameter to "
"compute the polyhole.\n"
"See http://hydraraptor.blogspot.com/2011/02/polyholes.html"
msgstr ""

msgid "Polyhole detection margin"
msgstr ""

#, no-c-format, no-boost-format
msgid ""
"Maximum defection of a point to the estimated radius of the circle.\n"
"As cylinders are often exported as triangles of varying size, points may not "
"be on the circle circumference. This setting allows you some leeway to "
"broaden the detection.\n"
"In mm or in % of the radius."
msgstr ""

msgid "Polyhole twist"
msgstr ""

msgid "Rotate the polyhole every layer."
msgstr ""

msgid "G-code thumbnails"
msgstr ""

msgid ""
"Picture sizes to be stored into a .gcode and .sl1 / .sl1s files, in the "
"following format: \"XxY, XxY, ...\""
msgstr ""

msgid "Format of G-code thumbnails"
msgstr ""

msgid ""
"Format of G-code thumbnails: PNG for best quality, JPG for smallest size, "
"QOI for low memory firmware"
msgstr ""

msgid "Use relative E distances"
msgstr ""

msgid ""
"Relative extrusion is recommended when using \"label_objects\" option. Some "
"extruders work better with this option unchecked (absolute extrusion mode). "
"Wipe tower is only compatible with relative mode. It is recommended on most "
"printers. Default is checked."
msgstr ""

msgid ""
"Classic wall generator produces walls with constant extrusion width and for "
"very thin areas is used gap-fill. Arachne engine produces walls with "
"variable extrusion width"
msgstr ""
"The classic wall generator produces walls with constant extrusion width and "
"for very thin areas, gap-fill is used. The Arachne engine produces walls "
"with variable extrusion width."

msgid "Arachne"
msgstr ""

msgid "Wall transition length"
msgstr ""

msgid ""
"When transitioning between different numbers of walls as the part becomes "
"thinner, a certain amount of space is allotted to split or join the wall "
"segments. It's expressed as a percentage over nozzle diameter"
msgstr ""
"When transitioning between different numbers of walls as the part becomes "
"thinner, a certain amount of space is allotted to split or join the wall "
"segments. It's expressed as a percentage over nozzle diameter."

msgid "Wall transitioning filter margin"
msgstr ""

msgid ""
"Prevent transitioning back and forth between one extra wall and one less. "
"This margin extends the range of extrusion widths which follow to [Minimum "
"wall width - margin, 2 * Minimum wall width + margin]. Increasing this "
"margin reduces the number of transitions, which reduces the number of "
"extrusion starts/stops and travel time. However, large extrusion width "
"variation can lead to under- or overextrusion problems. It's expressed as a "
"percentage over nozzle diameter"
msgstr ""

msgid "Wall transitioning threshold angle"
msgstr ""

msgid ""
"When to create transitions between even and odd numbers of walls. A wedge "
"shape with an angle greater than this setting will not have transitions and "
"no walls will be printed in the center to fill the remaining space. Reducing "
"this setting reduces the number and length of these center walls, but may "
"leave gaps or overextrude"
msgstr ""

msgid "Wall distribution count"
msgstr ""

msgid ""
"The number of walls, counted from the center, over which the variation needs "
"to be spread. Lower values mean that the outer walls don't change in width"
msgstr ""

msgid "Minimum feature size"
msgstr ""

msgid ""
"Minimum thickness of thin features. Model features that are thinner than "
"this value will not be printed, while features thicker than this value will "
"be widened to the minimum wall width. It's expressed as a percentage over "
"nozzle diameter."
msgstr ""

msgid "Minimum wall length"
msgstr ""

msgid ""
"Adjust this value to prevent short, unclosed walls from being printed, which "
"could increase print time. Higher values remove more and longer walls.\n"
"\n"
"NOTE: Bottom and top surfaces will not be affected by this value to prevent "
"visual gaps on the outside of the model. Adjust 'One wall threshold' in the "
"Advanced settings below to adjust the sensitivity of what is considered a "
"top-surface. 'One wall threshold' is only visible if this setting is set "
"above the default value of 0.5, or if single-wall top surfaces is enabled."
msgstr ""

msgid "First layer minimum wall width"
msgstr ""

msgid ""
"The minimum wall width that should be used for the first layer is "
"recommended to be set to the same size as the nozzle. This adjustment is "
"expected to enhance adhesion."
msgstr ""

msgid "Minimum wall width"
msgstr ""

msgid ""
"Width of the wall that will replace thin features (according to the Minimum "
"feature size) of the model. If the Minimum wall width is thinner than the "
"thickness of the feature, the wall will become as thick as the feature "
"itself. It's expressed as a percentage over nozzle diameter"
msgstr ""

msgid "Detect narrow internal solid infill"
msgstr ""

msgid ""
"This option will auto-detect narrow internal solid infill areas. If enabled, "
"the concentric pattern will be used for the area to speed up printing. "
"Otherwise, the rectilinear pattern will be used by default."
msgstr ""

msgid "invalid value "
msgstr ""

msgid "Invalid value when spiral vase mode is enabled: "
msgstr ""

msgid "too large line width "
msgstr ""

msgid " not in range "
msgstr ""

msgid "Export 3MF"
msgstr "Export 3mf"

msgid "Export project as 3MF."
msgstr "This exports the project as a 3mf file."

msgid "Export slicing data"
msgstr ""

msgid "Export slicing data to a folder."
msgstr "Export slicing data to a folder"

msgid "Load slicing data"
msgstr ""

msgid "Load cached slicing data from directory"
msgstr ""

msgid "Export STL"
msgstr ""

msgid "Export the objects as single STL."
msgstr ""

msgid "Export multiple STLs"
msgstr ""

msgid "Export the objects as multiple STLs to directory"
msgstr ""

msgid "Slice"
msgstr ""

msgid "Slice the plates: 0-all plates, i-plate i, others-invalid"
msgstr ""

msgid "Show command help."
msgstr "This shows command help."

msgid "UpToDate"
msgstr ""

msgid "Update the configs values of 3mf to latest."
msgstr ""

msgid "downward machines check"
msgstr ""

msgid ""
"check whether current machine downward compatible with the machines in the "
"list"
msgstr ""

msgid "Load default filaments"
msgstr ""

msgid "Load first filament as default for those not loaded"
msgstr ""

msgid "Minimum save"
msgstr ""

msgid "export 3mf with minimum size."
msgstr ""

msgid "mtcpp"
msgstr ""

msgid "max triangle count per plate for slicing."
msgstr "max triangle count per plate for slicing"

msgid "mstpp"
msgstr ""

msgid "max slicing time per plate in seconds."
msgstr "max slicing time per plate in seconds"

msgid "No check"
msgstr ""

msgid "Do not run any validity checks, such as G-code path conflicts check."
msgstr ""

msgid "Normative check"
msgstr ""

msgid "Check the normative items."
msgstr ""

msgid "Output Model Info"
msgstr ""

msgid "Output the model's information."
msgstr "This outputs the model’s information."

msgid "Export Settings"
msgstr ""

msgid "Export settings to a file."
msgstr "This exports settings to a file."

msgid "Send progress to pipe"
msgstr ""

msgid "Send progress to pipe."
msgstr ""

msgid "Arrange Options"
msgstr ""

msgid "Arrange options: 0-disable, 1-enable, others-auto"
msgstr ""

msgid "Repetition count"
msgstr ""

msgid "Repetition count of the whole model."
msgstr ""

msgid "Ensure on bed"
msgstr ""

msgid ""
"Lift the object above the bed when it is partially below. Disabled by default"
msgstr ""

msgid ""
"Arrange the supplied models in a plate and merge them in a single model in "
"order to perform actions once."
msgstr ""

msgid "Convert Unit"
msgstr ""

msgid "Convert the units of model"
msgstr ""

msgid "Orient Options"
msgstr ""

msgid "Orient options: 0-disable, 1-enable, others-auto"
msgstr ""

msgid "Rotation angle around the Z axis in degrees."
msgstr ""

msgid "Rotate around Y"
msgstr ""

msgid "Rotation angle around the Y axis in degrees."
msgstr ""

msgid "Scale the model by a float factor"
msgstr ""

msgid "Load General Settings"
msgstr ""

msgid "Load process/machine settings from the specified file"
msgstr ""

msgid "Load Filament Settings"
msgstr ""

msgid "Load filament settings from the specified file list"
msgstr ""

msgid "Skip Objects"
msgstr ""

msgid "Skip some objects in this print"
msgstr ""

msgid "Clone Objects"
msgstr ""

msgid "Clone objects in the load list"
msgstr ""

msgid "load uptodate process/machine settings when using uptodate"
msgstr ""

msgid ""
"load uptodate process/machine settings from the specified file when using "
"uptodate"
msgstr ""
"load up-to-date process/machine settings from the specified file when using "
"up-to-date"

msgid "load uptodate filament settings when using uptodate"
msgstr ""

msgid ""
"load uptodate filament settings from the specified file when using uptodate"
msgstr ""

msgid ""
"if enabled, check whether current machine downward compatible with the "
"machines in the list"
msgstr ""

msgid "downward machines settings"
msgstr ""

msgid "The machine settings list needs to do downward checking."
msgstr ""

msgid "Load assemble list"
msgstr ""

msgid "Load assemble object list from config file"
msgstr ""

msgid "Data directory"
msgstr ""

msgid ""
"Load and store settings at the given directory. This is useful for "
"maintaining different profiles or including configurations from a network "
"storage."
msgstr ""

msgid "Output directory"
msgstr ""

msgid "Output directory for the exported files."
msgstr "This is the output directory for exported files."

msgid "Debug level"
msgstr ""

msgid ""
"Sets debug logging level. 0:fatal, 1:error, 2:warning, 3:info, 4:debug, "
"5:trace\n"
msgstr ""

msgid "Enable timelapse for print"
msgstr ""

msgid "If enabled, this slicing will be considered using timelapse"
msgstr ""

msgid "Load custom G-code"
msgstr ""

msgid "Load custom G-code from json."
msgstr ""

msgid "Load filament ids"
msgstr ""

msgid "Load filament ids for each object"
msgstr ""

msgid "Allow multiple colors on one plate"
msgstr ""

msgid "If enabled, Arrange will allow multiple colors on one plate."
msgstr ""

msgid "Allow rotation when arranging"
msgstr ""

msgid "If enabled, Arrange will allow rotation when placing objects."
msgstr ""

msgid "Avoid extrusion calibrate region when arranging"
msgstr ""

msgid ""
"If enabled, Arrange will avoid extrusion calibrate region when placing "
"objects."
msgstr ""

msgid "Skip modified G-code in 3mf"
msgstr ""

msgid "Skip the modified G-code in 3mf from Printer or filament Presets."
msgstr ""

msgid "MakerLab name"
msgstr ""

msgid "MakerLab name to generate this 3mf"
msgstr ""

msgid "MakerLab version"
msgstr ""

msgid "MakerLab version to generate this 3mf"
msgstr ""

msgid "metadata name list"
msgstr ""

msgid "metadata name list added into 3mf"
msgstr ""

msgid "metadata value list"
msgstr ""

msgid "metadata value list added into 3mf"
msgstr ""

msgid "Allow 3mf with newer version to be sliced"
msgstr ""

msgid "Current Z-hop"
msgstr ""

msgid "Contains Z-hop present at the beginning of the custom G-code block."
msgstr ""

msgid ""
"Position of the extruder at the beginning of the custom G-code block. If the "
"custom G-code travels somewhere else, it should write to this variable so "
"OrcaSlicer knows where it travels from when it gets control back."
msgstr ""

msgid ""
"Retraction state at the beginning of the custom G-code block. If the custom "
"G-code moves the extruder axis, it should write to this variable so "
"OrcaSlicer de-retracts correctly when it gets control back."
msgstr ""

msgid "Extra de-retraction"
msgstr ""

msgid "Currently planned extra extruder priming after de-retraction."
msgstr ""

msgid "Absolute E position"
msgstr ""

msgid ""
"Current position of the extruder axis. Only used with absolute extruder "
"addressing."
msgstr ""

msgid "Current extruder"
msgstr ""

msgid "Zero-based index of currently used extruder."
msgstr ""

msgid "Current object index"
msgstr ""

msgid ""
"Specific for sequential printing. Zero-based index of currently printed "
"object."
msgstr ""

msgid "Has wipe tower"
msgstr ""

msgid "Whether or not wipe tower is being generated in the print."
msgstr ""

msgid "Initial extruder"
msgstr ""

msgid ""
"Zero-based index of the first extruder used in the print. Same as "
"initial_tool."
msgstr ""

msgid "Initial tool"
msgstr ""

msgid ""
"Zero-based index of the first extruder used in the print. Same as "
"initial_extruder."
msgstr ""

msgid "Is extruder used?"
msgstr ""

msgid ""
"Vector of booleans stating whether a given extruder is used in the print."
msgstr ""

msgid "Has single extruder MM priming"
msgstr ""

msgid "Are the extra multi-material priming regions used in this print?"
msgstr ""

msgid "Volume per extruder"
msgstr ""

msgid "Total filament volume extruded per extruder during the entire print."
msgstr ""

msgid "Total tool changes"
msgstr ""

msgid "Number of tool changes during the print."
msgstr ""

msgid "Total volume"
msgstr ""

msgid "Total volume of filament used during the entire print."
msgstr ""

msgid "Weight per extruder"
msgstr ""

msgid ""
"Weight per extruder extruded during the entire print. Calculated from "
"filament_density value in Filament Settings."
msgstr ""

msgid "Total weight"
msgstr ""

msgid ""
"Total weight of the print. Calculated from filament_density value in "
"Filament Settings."
msgstr ""

msgid "Total layer count"
msgstr ""

msgid "Number of layers in the entire print."
msgstr ""

msgid "Number of objects"
msgstr ""

msgid "Total number of objects in the print."
msgstr ""

msgid "Number of instances"
msgstr ""

msgid "Total number of object instances in the print, summed over all objects."
msgstr ""

msgid "Scale per object"
msgstr ""

msgid ""
"Contains a string with the information about what scaling was applied to the "
"individual objects. Indexing of the objects is zero-based (first object has "
"index 0).\n"
"Example: 'x:100% y:50% z:100'."
msgstr ""

msgid "Input filename without extension"
msgstr ""

msgid "Source filename of the first object, without extension."
msgstr ""

msgid ""
"The vector has two elements: x and y coordinate of the point. Values in mm."
msgstr ""

msgid ""
"The vector has two elements: x and y dimension of the bounding box. Values "
"in mm."
msgstr ""

msgid "First layer convex hull"
msgstr ""

msgid ""
"Vector of points of the first layer convex hull. Each element has the "
"following format:'[x, y]' (x and y are floating-point numbers in mm)."
msgstr ""

msgid "Bottom-left corner of first layer bounding box"
msgstr ""

msgid "Top-right corner of first layer bounding box"
msgstr ""

msgid "Size of the first layer bounding box"
msgstr ""

msgid "Bottom-left corner of print bed bounding box"
msgstr ""

msgid "Top-right corner of print bed bounding box"
msgstr ""

msgid "Size of the print bed bounding box"
msgstr ""

msgid "Timestamp"
msgstr ""

msgid "String containing current time in yyyyMMdd-hhmmss format."
msgstr ""

msgid "Day"
msgstr ""

msgid "Hour"
msgstr ""

msgid "Minute"
msgstr ""

msgid "Print preset name"
msgstr ""

msgid "Name of the print preset used for slicing."
msgstr ""

msgid "Filament preset name"
msgstr ""

msgid ""
"Names of the filament presets used for slicing. The variable is a vector "
"containing one name for each extruder."
msgstr ""

msgid "Printer preset name"
msgstr ""

msgid "Name of the printer preset used for slicing."
msgstr ""

msgid "Physical printer name"
msgstr ""

msgid "Name of the physical printer used for slicing."
msgstr ""

msgid "Number of extruders"
msgstr ""

msgid ""
"Total number of extruders, regardless of whether they are used in the "
"current print."
msgstr ""

msgid "Layer number"
msgstr ""

msgid "Index of the current layer. One-based (i.e. first layer is number 1)."
msgstr ""

msgid "Layer z"
msgstr ""

msgid ""
"Height of the current layer above the print bed, measured to the top of the "
"layer."
msgstr ""

msgid "Maximal layer z"
msgstr ""

msgid "Height of the last layer above the print bed."
msgstr ""

msgid "Filament extruder ID"
msgstr ""

msgid "The current extruder ID. The same as current_extruder."
msgstr ""

msgid "Error in zip archive"
msgstr ""

msgid "Generating walls"
msgstr ""

msgid "Generating infill regions"
msgstr ""

msgid "Generating infill toolpath"
msgstr ""

msgid "Detect overhangs for auto-lift"
msgstr ""

msgid "Checking support necessity"
msgstr ""

msgid "floating regions"
msgstr ""

msgid "floating cantilever"
msgstr ""

msgid "large overhangs"
msgstr ""

#, c-format, boost-format
msgid ""
"It seems object %s has %s. Please re-orient the object or enable support "
"generation."
msgstr ""

msgid "Generating support"
msgstr ""

msgid "Optimizing toolpath"
msgstr ""

msgid "Slicing mesh"
msgstr ""

msgid ""
"No layers were detected. You might want to repair your STL file(s) or check "
"their size or thickness and retry.\n"
msgstr ""

msgid ""
"An object's XY size compensation will not be used because it is also color-"
"painted.\n"
"XY Size compensation cannot be combined with color-painting."
msgstr ""

msgid "Support: generate contact points"
msgstr ""

msgid ""
"Unknown file format. Input file must have .stl, .obj, .amf(.xml) extension."
msgstr ""
"Unknown file format: input file must have .stl, .obj, or .amf(.xml) "
"extension."

msgid "Loading of a model file failed."
msgstr "Loading of model file failed."

msgid "The supplied file couldn't be read because it's empty"
msgstr "The supplied file couldn't be read because it's empty."

msgid "Unknown file format. Input file must have .3mf or .zip.amf extension."
msgstr "Unknown file format: input file must have .3mf or .zip.amf extension."

msgid "load_obj: failed to parse"
msgstr ""

msgid "load mtl in obj: failed to parse"
msgstr ""

msgid "The file contains polygons with more than 4 vertices."
msgstr ""

msgid "The file contains polygons with less than 2 vertices."
msgstr ""

msgid "The file contains invalid vertex index."
msgstr ""

msgid "This OBJ file couldn't be read because it's empty."
msgstr ""

msgid "Flow Rate Calibration"
msgstr ""

msgid "Max Volumetric Speed Calibration"
msgstr ""

msgid "Manage Result"
msgstr ""

msgid "Manual Calibration"
msgstr ""

msgid "Result can be read by human eyes."
msgstr ""

msgid "Auto-Calibration"
msgstr ""

msgid "We would use Lidar to read the calibration result"
msgstr ""

msgid "Prev"
msgstr ""

msgid "Recalibration"
msgstr ""

msgid "Calibrate"
msgstr ""

msgid "Finish"
msgstr ""

msgid "How to use calibration result?"
msgstr "How can I use calibration results?"

msgid ""
"You could change the Flow Dynamics Calibration Factor in material editing"
msgstr ""

msgid ""
"The current firmware version of the printer does not support calibration.\n"
"Please upgrade the printer firmware."
msgstr ""

msgid "Calibration not supported"
msgstr ""

msgid "Error desc"
msgstr ""

msgid "Extra info"
msgstr ""

msgid "Flow Dynamics"
msgstr ""

msgid "Flow Rate"
msgstr ""

msgid "Max Volumetric Speed"
msgstr ""

#, c-format, boost-format
msgid ""
"Please input valid values:\n"
"Start value: >= %.1f\n"
"End value: <= %.1f\n"
"End value: > Start value\n"
"Value step: >= %.3f)"
msgstr ""

msgid "The name cannot be empty."
msgstr ""

#, c-format, boost-format
msgid "The selected preset: %s was not found."
msgstr ""

msgid "The name cannot be the same as the system preset name."
msgstr ""

msgid "The name is the same as another existing preset name"
msgstr ""

msgid "create new preset failed."
msgstr ""

msgid ""
"Are you sure to cancel the current calibration and return to the home page?"
msgstr ""

msgid "No Printer Connected!"
msgstr ""

msgid "Printer is not connected yet."
msgstr ""

msgid "Please select filament to calibrate."
msgstr ""

msgid "The input value size must be 3."
msgstr ""

msgid ""
"This machine type can only hold 16 history results per nozzle. You can "
"delete the existing historical results and then start calibration. Or you "
"can continue the calibration, but you cannot create new calibration "
"historical results.\n"
"Do you still want to continue the calibration?"
msgstr ""
"This machine type can only hold 16 historical results per nozzle. You can "
"delete the existing historical results and then start calibration. Or you "
"can continue the calibration, but you cannot create new calibration "
"historical results.\n"
"Do you still want to continue the calibration?"

msgid "Connecting to printer..."
msgstr ""

msgid "The failed test result has been dropped."
msgstr ""

msgid "Flow Dynamics Calibration result has been saved to the printer"
msgstr ""

#, c-format, boost-format
msgid ""
"There is already a historical calibration result with the same name: %s. "
"Only one of the results with the same name is saved. Are you sure you want "
"to override the historical result?"
msgstr ""
"There is already a previous calibration result with the same name: %s. Only "
"one result with a name is saved. Are you sure you want to overwrite the "
"previous result?"

#, c-format, boost-format
msgid ""
"This machine type can only hold %d history results per nozzle. This result "
"will not be saved."
msgstr ""
"This machine type can only hold %d historical results per nozzle. This "
"result will not be saved."

msgid "Internal Error"
msgstr ""

msgid "Please select at least one filament for calibration"
msgstr ""

msgid "Flow rate calibration result has been saved to preset"
msgstr ""

msgid "Max volumetric speed calibration result has been saved to preset"
msgstr ""

msgid "When do you need Flow Dynamics Calibration"
msgstr ""

msgid ""
"We now have added the auto-calibration for different filaments, which is "
"fully automated and the result will be saved into the printer for future "
"use. You only need to do the calibration in the following limited cases:\n"
"1. If you introduce a new filament of different brands/models or the "
"filament is damp;\n"
"2. If the nozzle is worn out or replaced with a new one;\n"
"3. If the max volumetric speed or print temperature is changed in the "
"filament setting."
msgstr ""

msgid "About this calibration"
msgstr ""

msgid ""
"Please find the details of Flow Dynamics Calibration from our wiki.\n"
"\n"
"Usually the calibration is unnecessary. When you start a single color/"
"material print, with the \"flow dynamics calibration\" option checked in the "
"print start menu, the printer will follow the old way, calibrate the "
"filament before the print; When you start a multi color/material print, the "
"printer will use the default compensation parameter for the filament during "
"every filament switch which will have a good result in most cases.\n"
"\n"
"Please note that there are a few cases that can make the calibration results "
"unreliable, such as insufficient adhesion on the build plate. Improving "
"adhesion can be achieved by washing the build plate or applying glue. For "
"more information on this topic, please refer to our Wiki.\n"
"\n"
"The calibration results have about 10 percent jitter in our test, which may "
"cause the result not exactly the same in each calibration. We are still "
"investigating the root cause to do improvements with new updates."
msgstr ""

msgid "When to use Flow Rate Calibration"
msgstr ""

msgid ""
"After using Flow Dynamics Calibration, there might still be some extrusion "
"issues, such as:\n"
"1. Over-Extrusion: Excess material on your printed object, forming blobs or "
"zits, or the layers seem thicker than expected and not uniform.\n"
"2. Under-Extrusion: Very thin layers, weak infill strength, or gaps in the "
"top layer of the model, even when printing slowly.\n"
"3. Poor Surface Quality: The surface of your prints seems rough or uneven.\n"
"4. Weak Structural Integrity: Prints break easily or don't seem as sturdy as "
"they should be."
msgstr ""

msgid ""
"In addition, Flow Rate Calibration is crucial for foaming materials like LW-"
"PLA used in RC planes. These materials expand greatly when heated, and "
"calibration provides a useful reference flow rate."
msgstr ""

msgid ""
"Flow Rate Calibration measures the ratio of expected to actual extrusion "
"volumes. The default setting works well in Bambu Lab printers and official "
"filaments as they were pre-calibrated and fine-tuned. For a regular "
"filament, you usually won't need to perform a Flow Rate Calibration unless "
"you still see the listed defects after you have done other calibrations. For "
"more details, please check out the wiki article."
msgstr ""

msgid ""
"Auto Flow Rate Calibration utilizes Bambu Lab's Micro-Lidar technology, "
"directly measuring the calibration patterns. However, please be advised that "
"the efficacy and accuracy of this method may be compromised with specific "
"types of materials. Particularly, filaments that are transparent or semi-"
"transparent, sparkling-particled, or have a high-reflective finish may not "
"be suitable for this calibration and can produce less-than-desirable "
"results.\n"
"\n"
"The calibration results may vary between each calibration or filament. We "
"are still improving the accuracy and compatibility of this calibration "
"through firmware updates over time.\n"
"\n"
"Caution: Flow Rate Calibration is an advanced process, to be attempted only "
"by those who fully understand its purpose and implications. Incorrect usage "
"can lead to sub-par prints or printer damage. Please make sure to carefully "
"read and understand the process before doing it."
msgstr ""
"Auto Flow Rate Calibration utilizes Bambu Lab's Micro-Lidar technology, "
"directly measuring the calibration patterns. However, please be advised that "
"the efficacy and accuracy of this method may be compromised with specific "
"types of materials. Particularly, filaments that are transparent or semi-"
"transparent, have sparkles, or have a highly-reflective finish may not be "
"suitable for this calibration and can produce less-than-desirable results.\n"
"\n"
"The calibration results may vary between each calibration or filament. We "
"are still improving the accuracy and compatibility of this calibration "
"through firmware updates over time.\n"
"\n"
"Caution: Flow Rate Calibration is an advanced process, to be attempted only "
"by those who fully understand its purpose and implications. Incorrect usage "
"can lead to sub-par prints or printer damage. Please make sure to carefully "
"read and understand the process before doing it."

msgid "When you need Max Volumetric Speed Calibration"
msgstr ""

msgid "Over-extrusion or under extrusion"
msgstr ""

msgid "Max Volumetric Speed calibration is recommended when you print with:"
msgstr ""

msgid "material with significant thermal shrinkage/expansion, such as..."
msgstr ""

msgid "materials with inaccurate filament diameter"
msgstr ""

msgid "We found the best Flow Dynamics Calibration Factor"
msgstr ""

msgid ""
"Part of the calibration failed! You may clean the plate and retry. The "
"failed test result would be dropped."
msgstr ""

msgid ""
"*We recommend you to add brand, materia, type, and even humidity level in "
"the Name"
msgstr ""

msgid "Failed"
msgstr ""

msgid "Please enter the name you want to save to printer."
msgstr ""

msgid "The name cannot exceed 40 characters."
msgstr ""

msgid ""
"Only one of the results with the same name will be saved. Are you sure you "
"want to overwrite the other results?"
msgstr ""
"Only one of the results with the same name will be saved. Are you sure you "
"want to replace the other results?"

msgid "Please find the best line on your plate"
msgstr ""

msgid "Please find the corner with perfect degree of extrusion"
msgstr "Please find the corner with the perfect degree of extrusion"

msgid "Input Value"
msgstr ""

msgid "Save to Filament Preset"
msgstr ""

msgid "Preset"
msgstr ""

msgid "Record Factor"
msgstr ""

msgid "We found the best flow ratio for you"
msgstr ""

msgid "Flow Ratio"
msgstr ""

msgid "Please input a valid value (0.0 < flow ratio < 2.0)"
msgstr ""

msgid "Please enter the name of the preset you want to save."
msgstr ""

msgid "Calibration1"
msgstr ""

msgid "Calibration2"
msgstr ""

msgid "Please find the best object on your plate"
msgstr ""

msgid "Fill in the value above the block with smoothest top surface"
msgstr ""

msgid "Skip Calibration2"
msgstr ""

#, c-format, boost-format
msgid "flow ratio : %s "
msgstr ""

msgid "Please choose a block with smoothest top surface"
msgstr ""

msgid "Please choose a block with smoothest top surface."
msgstr ""

msgid "Please input a valid value (0 <= Max Volumetric Speed <= 60)"
msgstr ""

msgid "Calibration Type"
msgstr ""

msgid "Complete Calibration"
msgstr ""

msgid "Fine Calibration based on flow ratio"
msgstr ""

msgid "Title"
msgstr ""

msgid ""
"A test model will be printed. Please clear the build plate and place it back "
"to the hot bed before calibration."
msgstr ""

msgid "Printing Parameters"
msgstr ""

msgid "Plate Type"
msgstr ""

msgid "filament position"
msgstr ""

msgid "External Spool"
msgstr ""

msgid "Filament For Calibration"
msgstr ""

msgid ""
"Tips for calibration material: \n"
"- Materials that can share same hot bed temperature\n"
"- Different filament brand and family (Brand = Bambu, Family = Basic, Matte)"
msgstr ""

msgid "Pattern"
msgstr ""

msgid "Method"
msgstr ""

#, c-format, boost-format
msgid "%s is not compatible with %s"
msgstr ""

msgid "TPU is not supported for Flow Dynamics Auto-Calibration."
msgstr ""

msgid "Connecting to printer"
msgstr ""

msgid "From k Value"
msgstr ""

msgid "To k Value"
msgstr ""

msgid "Step value"
msgstr ""

msgid "The nozzle diameter has been synchronized from the printer Settings"
msgstr ""

msgid "From Volumetric Speed"
msgstr ""

msgid "To Volumetric Speed"
msgstr ""

msgid "Flow Dynamics Calibration Result"
msgstr ""

msgid "New"
msgstr ""

msgid "No History Result"
msgstr ""

msgid "Success to get history result"
msgstr ""

msgid "Refreshing the historical Flow Dynamics Calibration records"
msgstr "Refreshing the previous Flow Dynamics Calibration records"

msgid "Action"
msgstr ""

#, c-format, boost-format
msgid "This machine type can only hold %d history results per nozzle."
msgstr "This machine type can only hold %d historical results per nozzle."

msgid "Edit Flow Dynamics Calibration"
msgstr ""

msgid "New Flow Dynamic Calibration"
msgstr ""

msgid "Ok"
msgstr ""

msgid "The filament must be selected."
msgstr ""

msgid "Network lookup"
msgstr ""

msgid "Address"
msgstr ""

msgid "Hostname"
msgstr ""

msgid "Service name"
msgstr ""

msgid "OctoPrint version"
msgstr ""

msgid "Searching for devices"
msgstr ""

msgid "Finished"
msgstr ""

msgid "Multiple resolved IP addresses"
msgstr ""

#, boost-format
msgid ""
"There are several IP addresses resolving to hostname %1%.\n"
"Please select one that should be used."
msgstr ""

msgid "PA Calibration"
msgstr ""

msgid "DDE"
msgstr ""

msgid "Bowden"
msgstr ""

msgid "Extruder type"
msgstr ""

msgid "PA Tower"
msgstr ""

msgid "PA Line"
msgstr ""

msgid "PA Pattern"
msgstr ""

msgid "Start PA: "
msgstr ""

msgid "End PA: "
msgstr ""

msgid "PA step: "
msgstr ""

msgid "Accelerations: "
msgstr ""

msgid "Speeds: "
msgstr ""

msgid "Print numbers"
msgstr ""

msgid "Comma-separated list of printing accelerations"
msgstr ""

msgid "Comma-separated list of printing speeds"
msgstr ""

msgid ""
"Please input valid values:\n"
"Start PA: >= 0.0\n"
"End PA: > Start PA\n"
"PA step: >= 0.001)"
msgstr ""

msgid "Temperature calibration"
msgstr ""

msgid "PLA"
msgstr ""

msgid "ABS/ASA"
msgstr ""

msgid "PETG"
msgstr ""

msgid "PCTG"
msgstr ""

msgid "TPU"
msgstr ""

msgid "PA-CF"
msgstr ""

msgid "PET-CF"
msgstr ""

msgid "Filament type"
msgstr ""

msgid "Start temp: "
msgstr ""

msgid "End temp: "
msgstr ""

msgid "Temp step: "
msgstr ""

msgid ""
"Please input valid values:\n"
"Start temp: <= 350\n"
"End temp: >= 170\n"
"Start temp > End temp + 5)"
msgstr ""

msgid "Max volumetric speed test"
msgstr ""

msgid "Start volumetric speed: "
msgstr ""

msgid "End volumetric speed: "
msgstr ""

msgid "step: "
msgstr ""

msgid ""
"Please input valid values:\n"
"start > 0 \n"
"step >= 0\n"
"end > start + step)"
msgstr ""

msgid "VFA test"
msgstr ""

msgid "Start speed: "
msgstr ""

msgid "End speed: "
msgstr ""

msgid ""
"Please input valid values:\n"
"start > 10 \n"
"step >= 0\n"
"end > start + step)"
msgstr ""

msgid "Start retraction length: "
msgstr ""

msgid "End retraction length: "
msgstr ""

msgid "mm/mm"
msgstr ""

msgid "Send G-code to printer host"
msgstr ""

msgid "Upload to Printer Host with the following filename:"
msgstr ""

msgid "Use forward slashes ( / ) as a directory separator if needed."
msgstr ""

msgid "Upload to storage"
msgstr ""

msgid "Switch to Device tab after upload."
msgstr ""

#, c-format, boost-format
msgid "Upload filename doesn't end with \"%s\". Do you wish to continue?"
msgstr ""

msgid "Upload"
msgstr ""

msgid "Print host upload queue"
msgstr ""

msgid "ID"
msgstr ""

msgid "Progress"
msgstr ""

msgid "Host"
msgstr ""

msgctxt "OfFile"
msgid "Size"
msgstr ""

msgid "Filename"
msgstr ""

msgid "Cancel selected"
msgstr ""

msgid "Show error message"
msgstr ""

msgid "Queued"
msgstr ""

msgid "Uploading"
msgstr ""

msgid "Cancelling"
msgstr ""

msgid "Error uploading to print host"
msgstr ""

msgid ""
"The selected bed type does not match the file. Please confirm before "
"starting the print."
msgstr ""

msgid "Time-lapse"
msgstr ""

msgid "Heated Bed Leveling"
msgstr ""

msgid "Textured Build Plate (Side A)"
msgstr ""

msgid "Smooth Build Plate (Side B)"
msgstr ""

msgid "Unable to perform boolean operation on selected parts"
msgstr ""

msgid "Mesh Boolean"
msgstr ""

msgid "Union"
msgstr ""

msgid "Difference"
msgstr ""

msgid "Intersection"
msgstr ""

msgid "Source Volume"
msgstr ""

msgid "Tool Volume"
msgstr ""

msgid "Subtract from"
msgstr ""

msgid "Subtract with"
msgstr ""

msgid "selected"
msgstr ""

msgid "Part 1"
msgstr ""

msgid "Part 2"
msgstr ""

msgid "Delete input"
msgstr ""

msgid "Network Test"
msgstr ""

msgid "Start Test Multi-Thread"
msgstr ""

msgid "Start Test Single-Thread"
msgstr ""

msgid "Export Log"
msgstr ""

msgid "OrcaSlicer Version:"
msgstr ""

msgid "System Version:"
msgstr ""

msgid "DNS Server:"
msgstr ""

msgid "Test OrcaSlicer (GitHub)"
msgstr ""

msgid "Test OrcaSlicer (GitHub):"
msgstr ""

msgid "Test bing.com"
msgstr ""

msgid "Test bing.com:"
msgstr ""

msgid "Log Info"
msgstr ""

msgid "Select filament preset"
msgstr ""

msgid "Create Filament"
msgstr ""

msgid "Create Based on Current Filament"
msgstr ""

msgid "Copy Current Filament Preset "
msgstr ""

msgid "Basic Information"
msgstr ""

msgid "Add Filament Preset under this filament"
msgstr ""

msgid "We could create the filament presets for your following printer:"
msgstr ""

msgid "Select Vendor"
msgstr ""

msgid "Input Custom Vendor"
msgstr ""

msgid "Can't find vendor I want"
msgstr ""

msgid "Select Type"
msgstr ""

msgid "Select Filament Preset"
msgstr ""

msgid "Serial"
msgstr ""

msgid "e.g. Basic, Matte, Silk, Marble"
msgstr ""

msgid "Filament Preset"
msgstr ""

msgid "Create"
msgstr ""

msgid "Vendor is not selected, please reselect vendor."
msgstr "Vendor is not selected; please reselect vendor."

msgid "Custom vendor is not input, please input custom vendor."
msgstr "Custom vendor missing; please input custom vendor."

msgid ""
"\"Bambu\" or \"Generic\" cannot be used as a Vendor for custom filaments."
msgstr ""

msgid "Filament type is not selected, please reselect type."
msgstr ""

msgid "Filament serial is not entered, please enter serial."
msgstr "Filament serial missing; please input serial."

msgid ""
"There may be escape characters in the vendor or serial input of filament. "
"Please delete and re-enter."
msgstr ""
"There may be disallowed characters in the vendor or serial input of the "
"filament. Please delete and re-enter."

msgid "All inputs in the custom vendor or serial are spaces. Please re-enter."
msgstr ""

msgid "The vendor cannot be a number. Please re-enter."
msgstr "The vendor cannot be a number; please re-enter."

msgid ""
"You have not selected a printer or preset yet. Please select at least one."
msgstr ""

#, c-format, boost-format
msgid ""
"The Filament name %s you created already exists.\n"
"If you continue creating, the preset created will be displayed with its full "
"name. Do you want to continue?"
msgstr ""
"The Filament name %s you created already exists.\n"
"If you continue, the preset created will be displayed with its full name. Do "
"you want to continue?"

msgid "Some existing presets have failed to be created, as follows:\n"
msgstr ""

msgid ""
"\n"
"Do you want to rewrite it?"
msgstr ""

msgid ""
"We would rename the presets as \"Vendor Type Serial @printer you "
"selected\".\n"
"To add preset for more printers, please go to printer selection"
msgstr ""

msgid "Create Printer/Nozzle"
msgstr ""

msgid "Create Printer"
msgstr ""

msgid "Create Nozzle for Existing Printer"
msgstr ""

msgid "Create from Template"
msgstr ""

msgid "Create Based on Current Printer"
msgstr ""

msgid "Import Preset"
msgstr ""

msgid "Create Type"
msgstr ""

msgid "The model was not found, please reselect vendor."
msgstr "The model was not found; please reselect vendor."

msgid "Select Model"
msgstr ""

msgid "Select Printer"
msgstr ""

msgid "Input Custom Model"
msgstr ""

msgid "Can't find my printer model"
msgstr ""

msgid "Rectangle"
msgstr ""

msgid "Printable Space"
msgstr ""

msgid "Hot Bed STL"
msgstr ""

msgid "Load stl"
msgstr ""

msgid "Hot Bed SVG"
msgstr ""

msgid "Load svg"
msgstr ""

msgid "Max Print Height"
msgstr ""

#, c-format, boost-format
msgid "The file exceeds %d MB, please import again."
msgstr ""

msgid "Exception in obtaining file size, please import again."
msgstr ""

msgid "Preset path was not found, please reselect vendor."
msgstr "Preset path was not found; please reselect vendor."

msgid "The printer model was not found, please reselect."
msgstr ""

msgid "The nozzle diameter was not found, please reselect."
msgstr "The nozzle diameter was not found; please reselect."

msgid "The printer preset was not found, please reselect."
msgstr "The printer preset was not found; please reselect."

msgid "Printer Preset"
msgstr ""

msgid "Filament Preset Template"
msgstr ""

msgid "Deselect All"
msgstr ""

msgid "Process Preset Template"
msgstr ""

msgid "Back Page 1"
msgstr ""

msgid ""
"You have not yet chosen which printer preset to create based on. Please "
"choose the vendor and model of the printer"
msgstr ""

msgid ""
"You have entered an illegal input in the printable area section on the first "
"page. Please check before creating it."
msgstr ""
"You have entered a disallowed character in the printable area section on the "
"first page. Please use only numbers."

msgid "The custom printer or model is not entered, please enter it."
msgstr "The custom printer or model missing; please input."

msgid ""
"The printer preset you created already has a preset with the same name. Do "
"you want to overwrite it?\n"
"\tYes: Overwrite the printer preset with the same name, and filament and "
"process presets with the same preset name will be recreated \n"
"and filament and process presets without the same preset name will be "
"reserve.\n"
"\tCancel: Do not create a preset, return to the creation interface."
msgstr ""
"The printer preset you created already has a preset with the same name. Do "
"you want to overwrite it?\n"
"\tYes: Overwrite the printer preset with the same name, and filament and "
"process presets with the same preset name will be recreated \n"
"and filament and process presets without the same preset name will be "
"reserved.\n"
"\tCancel: Do not create a preset; return to the creation interface."

msgid "You need to select at least one filament preset."
msgstr ""

msgid "You need to select at least one process preset."
msgstr ""

msgid "Create filament presets failed. As follows:\n"
msgstr ""

msgid "Create process presets failed. As follows:\n"
msgstr ""

msgid "Vendor was not found, please reselect."
msgstr "Vendor was not found; please reselect."

msgid "Current vendor has no models, please reselect."
msgstr ""

msgid ""
"You have not selected the vendor and model or entered the custom vendor and "
"model."
msgstr ""
"You have not selected the vendor and model or input the custom vendor and "
"model."

msgid ""
"There may be escape characters in the custom printer vendor or model. Please "
"delete and re-enter."
msgstr ""

msgid ""
"All inputs in the custom printer vendor or model are spaces. Please re-enter."
msgstr ""

msgid "Please check bed printable shape and origin input."
msgstr ""

msgid ""
"You have not yet selected the printer to replace the nozzle, please choose."
msgstr ""
"You have not yet selected the printer to replace the nozzle for; please "
"choose a printer."

msgid "Printer Created Successfully"
msgstr ""

msgid "Filament Created Successfully"
msgstr ""

msgid "Printer Created"
msgstr ""

msgid "Please go to printer settings to edit your presets"
msgstr ""

msgid "Filament Created"
msgstr ""

msgid ""
"Please go to filament setting to edit your presets if you need.\n"
"Please note that nozzle temperature, hot bed temperature, and maximum "
"volumetric speed has a significant impact on printing quality. Please set "
"them carefully."
msgstr ""
"Please go to filament settings to edit your presets if you need to.\n"
"Please note that nozzle temperature, hot bed temperature, and maximum "
"volumetric speed each have a significant impact on printing quality. Please "
"set them carefully."

msgid ""
"\n"
"\n"
"Orca has detected that your user presets synchronization function is not "
"enabled, which may result in unsuccessful Filament settings on the Device "
"page.\n"
"Click \"Sync user presets\" to enable the synchronization function."
msgstr ""

msgid "Printer Setting"
msgstr ""

msgid "Printer config bundle(.orca_printer)"
msgstr ""

msgid "Filament bundle(.orca_filament)"
msgstr ""

msgid "Printer presets(.zip)"
msgstr ""

msgid "Filament presets(.zip)"
msgstr ""

msgid "Process presets(.zip)"
msgstr ""

msgid "initialize fail"
msgstr ""

msgid "add file fail"
msgstr ""

msgid "add bundle structure file fail"
msgstr ""

msgid "finalize fail"
msgstr ""

msgid "open zip written fail"
msgstr ""

msgid "Export successful"
msgstr ""

#, c-format, boost-format
msgid ""
"The '%s' folder already exists in the current directory. Do you want to "
"clear it and rebuild it.\n"
"If not, a time suffix will be added, and you can modify the name after "
"creation."
msgstr ""
"The '%s' folder already exists in the current directory. Do you want to "
"clear it and rebuild it?\n"
"If not, a time suffix will be added, and you can modify the name after "
"creation."

msgid ""
"Printer and all the filament&&process presets that belongs to the printer.\n"
"Can be shared with others."
msgstr ""

msgid ""
"User's filament preset set.\n"
"Can be shared with others."
msgstr ""

msgid ""
"Only display printer names with changes to printer, filament, and process "
"presets."
msgstr ""
"Only display printers with changes to printer, filament, and process presets "
"are displayed."

msgid "Only display the filament names with changes to filament presets."
msgstr ""

msgid ""
"Only printer names with user printer presets will be displayed, and each "
"preset you choose will be exported as a zip."
msgstr ""

msgid ""
"Only the filament names with user filament presets will be displayed, \n"
"and all user filament presets in each filament name you select will be "
"exported as a zip."
msgstr ""

msgid ""
"Only printer names with changed process presets will be displayed, \n"
"and all user process presets in each printer name you select will be "
"exported as a zip."
msgstr ""

msgid "Please select at least one printer or filament."
msgstr ""

msgid "Please select a type you want to export"
msgstr "Please select a preset type you want to export"

msgid "Failed to create temporary folder, please try Export Configs again."
msgstr ""

msgid "Edit Filament"
msgstr ""

msgid "Filament presets under this filament"
msgstr ""

msgid ""
"Note: If the only preset under this filament is deleted, the filament will "
"be deleted after exiting the dialog."
msgstr ""

msgid "Presets inherited by other presets cannot be deleted"
msgstr ""

msgid "The following presets inherits this preset."
msgid_plural "The following preset inherits this preset."
msgstr[0] ""
msgstr[1] ""

msgid "Delete Preset"
msgstr ""

msgid "Are you sure to delete the selected preset?"
msgstr ""

msgid "Delete preset"
msgstr ""

msgid "+ Add Preset"
msgstr ""

msgid "Delete Filament"
msgstr ""

msgid ""
"All the filament presets belong to this filament would be deleted.\n"
"If you are using this filament on your printer, please reset the filament "
"information for that slot."
msgstr ""

msgid "Delete filament"
msgstr ""

msgid "Add Preset"
msgstr ""

msgid "Add preset for new printer"
msgstr ""

msgid "Copy preset from filament"
msgstr ""

msgid "The filament choice not find filament preset, please reselect it"
msgstr ""

msgid "[Delete Required]"
msgstr ""

msgid "Edit Preset"
msgstr ""

msgid "For more information, please check out Wiki"
msgstr "For more information, please check out our Wiki"

msgid "Collapse"
msgstr ""

msgid "Daily Tips"
msgstr ""

#, c-format, boost-format
msgid "nozzle memorized: %.1f %s"
msgstr ""

msgid ""
"Your nozzle diameter in preset is not consistent with memorized nozzle "
"diameter. Did you change your nozzle lately?"
msgstr ""
"Your nozzle diameter in preset is not consistent with the saved nozzle "
"diameter. Have you changed your nozzle?"

#, c-format, boost-format
msgid "*Printing %s material with %s may cause nozzle damage"
msgstr ""

msgid "Need select printer"
msgstr ""

msgid "The start, end or step is not valid value."
msgstr ""

msgid ""
"Unable to calibrate: maybe because the set calibration value range is too "
"large, or the step is too small"
msgstr ""

#, fuzzy
msgid "Physical Printer"
msgstr "Printer"

msgid "Print Host upload"
msgstr ""

msgid "Test"
msgstr ""

msgid "Could not get a valid Printer Host reference"
msgstr ""

msgid "Success!"
msgstr ""

msgid "Are you sure to log out?"
msgstr ""

msgid "Refresh Printers"
msgstr ""

msgid "View print host webui in Device tab"
msgstr ""

msgid "Replace the BambuLab's device tab with print host webui"
msgstr ""

msgid ""
"HTTPS CA file is optional. It is only needed if you use HTTPS with a self-"
"signed certificate."
msgstr ""

msgid "Certificate files (*.crt, *.pem)|*.crt;*.pem|All files|*.*"
msgstr ""

msgid "Open CA certificate file"
msgstr ""

#, c-format, boost-format
msgid ""
"On this system, %s uses HTTPS certificates from the system Certificate Store "
"or Keychain."
msgstr ""

msgid ""
"To use a custom CA file, please import your CA file into Certificate Store / "
"Keychain."
msgstr ""

msgid "Login/Test"
msgstr ""

msgid "Connection to printers connected via the print host failed."
msgstr ""

#, c-format, boost-format
msgid "Mismatched type of print host: %s"
msgstr ""

msgid "Connection to AstroBox is working correctly."
msgstr ""

msgid "Could not connect to AstroBox"
msgstr ""

msgid "Note: AstroBox version 1.1.0 or higher is required."
msgstr ""

msgid "Connection to Duet is working correctly."
msgstr ""

msgid "Could not connect to Duet"
msgstr ""

msgid "Unknown error occurred"
msgstr ""

msgid "Wrong password"
msgstr ""

msgid "Could not get resources to create a new connection"
msgstr ""

msgid "Upload not enabled on FlashAir card."
msgstr ""

msgid "Connection to FlashAir is working correctly and upload is enabled."
msgstr ""

msgid "Could not connect to FlashAir"
msgstr ""

msgid ""
"Note: FlashAir with firmware 2.00.02 or newer and activated upload function "
"is required."
msgstr ""

msgid "Connection to MKS is working correctly."
msgstr ""

msgid "Could not connect to MKS"
msgstr ""

msgid "Connection to OctoPrint is working correctly."
msgstr ""

msgid "Could not connect to OctoPrint"
msgstr ""

msgid "Note: OctoPrint version 1.1.0 or higher is required."
msgstr ""

msgid "Connection to Prusa SL1 / SL1S is working correctly."
msgstr ""

msgid "Could not connect to Prusa SLA"
msgstr ""

msgid "Connection to PrusaLink is working correctly."
msgstr ""

msgid "Could not connect to PrusaLink"
msgstr ""

msgid "Storages found"
msgstr ""

#. TRN %1% = storage path
#, boost-format
msgid "%1% : read only"
msgstr ""

#. TRN %1% = storage path
#, boost-format
msgid "%1% : no free space"
msgstr ""

#. TRN %1% = host
#, boost-format
msgid "Upload has failed. There is no suitable storage found at %1%."
msgstr ""

msgid "Connection to Prusa Connect is working correctly."
msgstr ""

msgid "Could not connect to Prusa Connect"
msgstr ""

msgid "Connection to Repetier is working correctly."
msgstr ""

msgid "Could not connect to Repetier"
msgstr ""

msgid "Note: Repetier version 0.90.0 or higher is required."
msgstr ""

#, boost-format
msgid ""
"HTTP status: %1%\n"
"Message body: \"%2%\""
msgstr ""

#, boost-format
msgid ""
"Parsing of host response failed.\n"
"Message body: \"%1%\"\n"
"Error: \"%2%\""
msgstr ""

#, boost-format
msgid ""
"Enumeration of host printers failed.\n"
"Message body: \"%1%\"\n"
"Error: \"%2%\""
msgstr ""

msgid ""
"It has a small layer height. This results in almost negligible layer lines "
"and high print quality. It is suitable for most printing cases."
msgstr ""

msgid ""
"Compared with the default profile of a 0.2 mm nozzle, it has lower speeds "
"and acceleration, and the sparse infill pattern is Gyroid. This results in "
"much higher print quality but a much longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.2 mm nozzle, it has a slightly "
"bigger layer height. This results in almost negligible layer lines and "
"slightly shorter print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.2 mm nozzle, it has a bigger layer "
"height. This results in slightly visible layer lines but shorter print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer "
"height. This results in almost invisible layer lines and higher print "
"quality but shorter print time."
msgstr ""
"Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer "
"height. This results in almost invisible layer lines and higher print "
"quality but longer print time."

msgid ""
"Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer "
"lines, lower speeds and acceleration, and the sparse infill pattern is "
"Gyroid. This results in almost invisible layer lines and much higher print "
"quality but much longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer "
"height. This results in minimal layer lines and higher print quality but "
"shorter print time."
msgstr ""
"Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer "
"height. This results in minimal layer lines and higher print quality but "
"longer print time."

msgid ""
"Compared with the default profile of a 0.2 mm nozzle, it has a smaller layer "
"lines, lower speeds and acceleration, and the sparse infill pattern is "
"Gyroid. This results in minimal layer lines and much higher print quality "
"but much longer print time."
msgstr ""

msgid ""
"It has a normal layer height. This results in average layer lines and print "
"quality. It is suitable for most printing cases."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has more wall loops "
"and a higher sparse infill density. This results in higher print strength "
"but more filament consumption and longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer "
"height. This results in more apparent layer lines and lower print quality, "
"but slightly shorter print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has a bigger layer "
"height. This results in more apparent layer lines and lower print quality, "
"but shorter print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer "
"height. This results in less apparent layer lines and higher print quality "
"but longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer "
"height, lower speeds and acceleration, and the sparse infill pattern is "
"Gyroid. This results in less apparent layer lines and much higher print "
"quality but much longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer "
"height. This results in almost negligible layer lines and higher print "
"quality but longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer "
"height, lower speeds and acceleration, and the sparse infill pattern is "
"Gyroid. This results in almost negligible layer lines and much higher print "
"quality but much longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.4 mm nozzle, it has a smaller layer "
"height. This results in almost negligible layer lines and longer print time."
msgstr ""

msgid ""
"It has a big layer height. This results in apparent layer lines and ordinary "
"print quality and print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.6 mm nozzle, it has more wall loops "
"and a higher sparse infill density. This results in higher print strength "
"but more filament consumption and longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer "
"height. This results in more apparent layer lines and lower print quality, "
"but shorter print time in some cases."
msgstr ""

msgid ""
"Compared with the default profile of a 0.6 mm nozzle, it has a bigger layer "
"height. This results in much more apparent layer lines and much lower print "
"quality, but shorter print time in some cases."
msgstr ""

msgid ""
"Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer "
"height. This results in less apparent layer lines and slight higher print "
"quality but longer print time."
msgstr ""

msgid ""
"Compared with the default profile of a 0.6 mm nozzle, it has a smaller layer "
"height. This results in less apparent layer lines and higher print quality "
"but longer print time."
msgstr ""

msgid ""
"It has a very big layer height. This results in very apparent layer lines, "
"low print quality and general print time."
msgstr ""
"It has a very big layer height. This results in very apparent layer lines, "
"low print quality and shorter print time."

msgid ""
"Compared with the default profile of a 0.8 mm nozzle, it has a bigger layer "
"height. This results in very apparent layer lines and much lower print "
"quality but shorter print time in some cases."
msgstr ""

msgid ""
"Compared with the default profile of a 0.8 mm nozzle, it has a much bigger "
"layer height. This results in extremely apparent layer lines and much lower "
"print quality but much shorter print time in some cases."
msgstr ""

msgid ""
"Compared with the default profile of a 0.8 mm nozzle, it has a slightly "
"smaller layer height. This results in slightly less but still apparent layer "
"lines and slightly higher print quality but longer print time in some cases."
msgstr ""

msgid ""
"Compared with the default profile of a 0.8 mm nozzle, it has a smaller layer "
"height. This results in less but still apparent layer lines and slightly "
"higher print quality but longer print time in some cases."
msgstr ""

msgid "Connected to Obico successfully!"
msgstr ""

msgid "Could not connect to Obico"
msgstr ""

msgid "Connected to SimplyPrint successfully!"
msgstr ""

msgid "Could not connect to SimplyPrint"
msgstr ""

msgid "Internal error"
msgstr ""

msgid "Unknown error"
msgstr ""

msgid "SimplyPrint account not linked. Go to Connect options to set it up."
msgstr ""

msgid "Connection to Flashforge is working correctly."
msgstr ""

msgid "Could not connect to Flashforge"
msgstr ""

msgid "The provided state is not correct."
msgstr ""

msgid "Please give the required permissions when authorizing this application."
msgstr ""

msgid "Something unexpected happened when trying to log in, please try again."
msgstr ""

msgid "User canceled."
msgstr ""

msgid "Head diameter"
msgstr ""

msgid "Max angle"
msgstr ""

msgid "Detection radius"
msgstr ""

msgid "Remove selected points"
msgstr ""

msgid "Remove all"
msgstr ""

msgid "Auto-generate points"
msgstr ""

msgid "Add a brim ear"
msgstr ""

msgid "Delete a brim ear"
msgstr ""

msgid "Adjust section view"
msgstr ""

msgid ""
"Warning: The brim type is not set to \"painted\", the brim ears will not "
"take effect!"
msgstr ""

msgid "Set the brim type to \"painted\""
msgstr ""

msgid " invalid brim ears"
msgstr ""

msgid "Brim Ears"
msgstr ""

msgid "Please select single object."
msgstr ""

#: resources/data/hints.ini: [hint:Precise wall]
msgid ""
"Precise wall\n"
"Did you know that turning on precise wall can improve precision and layer "
"consistency?"
msgstr ""

#: resources/data/hints.ini: [hint:Sandwich mode]
msgid ""
"Sandwich mode\n"
"Did you know that you can use sandwich mode (inner-outer-inner) to improve "
"precision and layer consistency if your model doesn't have very steep "
"overhangs?"
msgstr ""

#: resources/data/hints.ini: [hint:Chamber temperature]
msgid ""
"Chamber temperature\n"
"Did you know that OrcaSlicer supports chamber temperature?"
msgstr ""

#: resources/data/hints.ini: [hint:Calibration]
msgid ""
"Calibration\n"
"Did you know that calibrating your printer can do wonders? Check out our "
"beloved calibration solution in OrcaSlicer."
msgstr ""

#: resources/data/hints.ini: [hint:Auxiliary fan]
msgid ""
"Auxiliary fan\n"
"Did you know that OrcaSlicer supports Auxiliary part cooling fan?"
msgstr ""

#: resources/data/hints.ini: [hint:Air filtration]
msgid ""
"Air filtration/Exhaust Fan\n"
"Did you know that OrcaSlicer can support Air filtration/Exhaust Fan?"
msgstr ""

#: resources/data/hints.ini: [hint:G-code window]
msgid ""
"G-code window\n"
"You can turn on/off the G-code window by pressing the <b>C</b> key."
msgstr ""

#: resources/data/hints.ini: [hint:Switch workspaces]
msgid ""
"Switch workspaces\n"
"You can switch between <b>Prepare</b> and <b>Preview</b> workspaces by "
"pressing the <b>Tab</b> key."
msgstr ""

#: resources/data/hints.ini: [hint:How to use keyboard shortcuts]
msgid ""
"How to use keyboard shortcuts\n"
"Did you know that Orca Slicer offers a wide range of keyboard shortcuts and "
"3D scene operations."
msgstr ""

#: resources/data/hints.ini: [hint:Reverse on odd]
msgid ""
"Reverse on odd\n"
"Did you know that <b>Reverse on odd</b> feature can significantly improve "
"the surface quality of your overhangs?"
msgstr ""

#: resources/data/hints.ini: [hint:Cut Tool]
msgid ""
"Cut Tool\n"
"Did you know that you can cut a model at any angle and position with the "
"cutting tool?"
msgstr ""

#: resources/data/hints.ini: [hint:Fix Model]
msgid ""
"Fix Model\n"
"Did you know that you can fix a corrupted 3D model to avoid a lot of slicing "
"problems on the Windows system?"
msgstr ""

#: resources/data/hints.ini: [hint:Timelapse]
msgid ""
"Timelapse\n"
"Did you know that you can generate a timelapse video during each print?"
msgstr ""

#: resources/data/hints.ini: [hint:Auto-Arrange]
msgid ""
"Auto-Arrange\n"
"Did you know that you can auto-arrange all objects in your project?"
msgstr ""
"Auto-Arrange\n"
"Did you know that you can auto-arrange all the objects in your project?"

#: resources/data/hints.ini: [hint:Auto-Orient]
msgid ""
"Auto-Orient\n"
"Did you know that you can rotate objects to an optimal orientation for "
"printing by a simple click?"
msgstr ""
"Auto-Orient\n"
"Did you know that you can rotate objects to an optimal orientation for "
"printing with a simple click?"

#: resources/data/hints.ini: [hint:Lay on Face]
msgid ""
"Lay on Face\n"
"Did you know that you can quickly orient a model so that one of its faces "
"sits on the print bed? Select the \"Place on face\" function or press the "
"<b>F</b> key."
msgstr ""

#: resources/data/hints.ini: [hint:Object List]
msgid ""
"Object List\n"
"Did you know that you can view all objects/parts in a list and change "
"settings for each object/part?"
msgstr ""

#: resources/data/hints.ini: [hint:Search Functionality]
msgid ""
"Search Functionality\n"
"Did you know that you use the Search tool to quickly find a specific Orca "
"Slicer setting?"
msgstr ""

#: resources/data/hints.ini: [hint:Simplify Model]
msgid ""
"Simplify Model\n"
"Did you know that you can reduce the number of triangles in a mesh using the "
"Simplify mesh feature? Right-click the model and select Simplify model."
msgstr ""

#: resources/data/hints.ini: [hint:Slicing Parameter Table]
msgid ""
"Slicing Parameter Table\n"
"Did you know that you can view all objects/parts on a table and change "
"settings for each object/part?"
msgstr ""

#: resources/data/hints.ini: [hint:Split to Objects/Parts]
msgid ""
"Split to Objects/Parts\n"
"Did you know that you can split a big object into small ones for easy "
"colorizing or printing?"
msgstr ""

#: resources/data/hints.ini: [hint:Subtract a Part]
msgid ""
"Subtract a Part\n"
"Did you know that you can subtract one mesh from another using the Negative "
"part modifier? That way you can, for example, create easily resizable holes "
"directly in Orca Slicer."
msgstr ""

#: resources/data/hints.ini: [hint:STEP]
msgid ""
"STEP\n"
"Did you know that you can improve your print quality by slicing a STEP file "
"instead of an STL?\n"
"Orca Slicer supports slicing STEP files, providing smoother results than a "
"lower resolution STL. Give it a try!"
msgstr ""

#: resources/data/hints.ini: [hint:Z seam location]
msgid ""
"Z seam location\n"
"Did you know that you can customize the location of the Z seam, and even "
"paint it on your print, to have it in a less visible location? This improves "
"the overall look of your model. Check it out!"
msgstr ""

#: resources/data/hints.ini: [hint:Fine-tuning for flow rate]
msgid ""
"Fine-tuning for flow rate\n"
"Did you know that flow rate can be fine-tuned for even better-looking "
"prints? Depending on the material, you can improve the overall finish of the "
"printed model by doing some fine-tuning."
msgstr ""

#: resources/data/hints.ini: [hint:Split your prints into plates]
msgid ""
"Split your prints into plates\n"
"Did you know that you can split a model that has a lot of parts into "
"individual plates ready to print? This will simplify the process of keeping "
"track of all the parts."
msgstr ""

#: resources/data/hints.ini: [hint:Speed up your print with Adaptive Layer
#: Height]
msgid ""
"Speed up your print with Adaptive Layer Height\n"
"Did you know that you can print a model even faster, by using the Adaptive "
"Layer Height option? Check it out!"
msgstr ""
"Speed up your print with Adaptive Layer Height\n"
"Did you know that you can print a model even faster by using the Adaptive "
"Layer Height option? Check it out!"

#: resources/data/hints.ini: [hint:Support painting]
msgid ""
"Support painting\n"
"Did you know that you can paint the location of your supports? This feature "
"makes it easy to place the support material only on the sections of the "
"model that actually need it."
msgstr ""

#: resources/data/hints.ini: [hint:Different types of supports]
msgid ""
"Different types of supports\n"
"Did you know that you can choose from multiple types of supports? Tree "
"supports work great for organic models, while saving filament and improving "
"print speed. Check them out!"
msgstr ""
"Different types of supports\n"
"Did you know that you can choose from multiple types of supports? Tree "
"supports work great for organic models while saving filament and improving "
"print speed. Check them out!"

#: resources/data/hints.ini: [hint:Printing Silk Filament]
msgid ""
"Printing Silk Filament\n"
"Did you know that Silk filament needs special consideration to print it "
"successfully? Higher temperature and lower speed are always recommended for "
"the best results."
msgstr ""
"Printing Silk Filament\n"
"Did you know that Silk filament needs special consideration to print "
"successfully? A higher temperature and lower speed are always recommended "
"for the best results."

#: resources/data/hints.ini: [hint:Brim for better adhesion]
msgid ""
"Brim for better adhesion\n"
"Did you know that when printed models have a small contact interface with "
"the printing surface, it's recommended to use a brim?"
msgstr ""

#: resources/data/hints.ini: [hint:Set parameters for multiple objects]
msgid ""
"Set parameters for multiple objects\n"
"Did you know that you can set slicing parameters for all selected objects at "
"one time?"
msgstr ""
"Set parameters for multiple objects\n"
"Did you know that you can set slicing parameters for all selected objects at "
"once?"

#: resources/data/hints.ini: [hint:Stack objects]
msgid ""
"Stack objects\n"
"Did you know that you can stack objects as a whole one?"
msgstr ""

#: resources/data/hints.ini: [hint:Flush into support/objects/infill]
msgid ""
"Flush into support/objects/infill\n"
"Did you know that you can save the wasted filament by flushing them into "
"support/objects/infill during filament change?"
msgstr ""
"Flush into support/objects/infill\n"
"Did you know that you can reduce wasted filament by flushing it into support/"
"objects/infill during filament changes?"

#: resources/data/hints.ini: [hint:Improve strength]
msgid ""
"Improve strength\n"
"Did you know that you can use more wall loops and higher sparse infill "
"density to improve the strength of the model?"
msgstr ""

#: resources/data/hints.ini: [hint:When need to print with the printer door
#: opened]
msgid ""
"When need to print with the printer door opened\n"
"Did you know that opening the printer door can reduce the probability of "
"extruder/hotend clogging when printing lower temperature filament with a "
"higher enclosure temperature. More info about this in the Wiki."
msgstr ""
"When do you need to print with the printer door opened?\n"
"Did you know that opening the printer door can reduce the probability of "
"extruder/hotend clogging when printing lower temperature filament with a "
"higher enclosure temperature? There is more info about this in the Wiki."

#: resources/data/hints.ini: [hint:Avoid warping]
msgid ""
"Avoid warping\n"
"Did you know that when printing materials that are prone to warping such as "
"ABS, appropriately increasing the heatbed temperature can reduce the "
"probability of warping."
msgstr ""
"Avoid warping\n"
"Did you know that when printing materials that are prone to warping such as "
"ABS, appropriately increasing the heatbed temperature can reduce the "
"probability of warping?"

#, c-format, boost-format
#~ msgid "Connect failed [%d]!"
#~ msgstr "Connection failed [%d]!"

#~ msgid "Initialize failed (Device connection not ready)!"
#~ msgstr "Initialization failed (Device connection not ready)!"

#, c-format, boost-format
#~ msgid "Initialize failed (%s)!"
#~ msgstr "Initialization failed (%s)!"

#~ msgid ""
#~ "Step 1, please confirm Orca Slicer and your printer are in the same LAN."
#~ msgstr ""
#~ "Step 1, please confirm that Orca Slicer and your printer are on the same "
#~ "LAN."

#~ msgid "Force cooling for overhang and bridge"
#~ msgstr "Force cooling for overhangs and bridges"

#~ msgid ""
#~ "Enable this option to optimize part cooling fan speed for overhang and "
#~ "bridge to get better cooling"
#~ msgstr ""
#~ "Enable this option to optimize the part cooling fan speed for overhangs "
#~ "and bridges to get better cooling"

#~ msgid "Fan speed for overhang"
#~ msgstr "Fan speed for overhangs"

#~ msgid ""
#~ "Force part cooling fan to be this speed when printing bridge or overhang "
#~ "wall which has large overhang degree. Forcing cooling for overhang and "
#~ "bridge can get better quality for these part"
#~ msgstr ""
#~ "Force part cooling fan to be this speed when printing bridges or overhang "
#~ "walls which have a large overhang degree. Forcing cooling for overhangs "
#~ "and bridges can achieve better quality for these parts."

#, c-format
#~ msgid ""
#~ "Force cooling fan to be specific speed when overhang degree of printed "
#~ "part exceeds this value. Expressed as percentage which indicates how much "
#~ "width of the line without support from lower layer. 0% means forcing "
#~ "cooling for all outer wall no matter how much overhang degree"
#~ msgstr ""
#~ "Force cooling fan to be a specific speed when overhang degree of printed "
#~ "part exceeds this value. This is expressed as a percentage which "
#~ "indicates how much width of the line without support from lower layer. "
#~ "0% means forcing cooling for all outer wall no matter the overhang degree."

#~ msgid ""
#~ "While printing by Object, the extruder may collide skirt.\n"
#~ "Thus, reset the skirt layer to 1 to avoid that."
#~ msgstr ""
#~ "While printing by object, the extruder may collide with a skirt.\n"
#~ "Thus, reset the skirt layer to 1 to avoid collisions."

#~ msgid ""
#~ "Decrease this value slightly (for example 0.9) to reduce the amount of "
#~ "material for bridge, to improve sag"
#~ msgstr ""
#~ "Decrease this value slightly (for example 0.9) to reduce the amount of "
#~ "material extruded for bridges to avoid sagging."

#~ msgid "Speed of bridge and completely overhang wall"
#~ msgstr "This is the speed for bridges and 100% overhang walls."

#~ msgid "Time to load new filament when switch filament. For statistics only"
#~ msgstr ""
#~ "Time to load new filament when switching filament, for statistical "
#~ "purposes only."

#~ msgid ""
#~ "Time to unload old filament when switch filament. For statistics only"
#~ msgstr ""
#~ "Time to unload old filament when switching filament, for statistical "
#~ "purposes only."

#~ msgid ""
#~ "Higher chamber temperature can help suppress or reduce warping and "
#~ "potentially lead to higher interlayer bonding strength for high "
#~ "temperature materials like ABS, ASA, PC, PA and so on. At the same time, "
#~ "the air filtration of ABS and ASA will get worse. While for PLA, PETG, "
#~ "TPU, PVA and other low temperature materials,the actual chamber "
#~ "temperature should not be high to avoid cloggings, so 0 which stands for "
#~ "turning off is highly recommended"
#~ msgstr ""
#~ "Higher chamber temperature can help suppress or reduce warping and "
#~ "potentially lead to higher interlayer bonding strength for high "
#~ "temperature materials like ABS, ASA, PC, PA and so on. At the same time, "
#~ "the air filtration of ABS and ASA will get worse. While for PLA, PETG, "
#~ "TPU, PVA and other low temperature materials, the actual chamber "
#~ "temperature should not be high to avoid clogs, so 0 (turned off) is "
#~ "highly recommended."

#~ msgid "Printer local connection failed, please try again."
#~ msgstr "Printer local connection failed; please try again."

#~ msgid ""
#~ "Please find the details of Flow Dynamics Calibration from our wiki.\n"
#~ "\n"
#~ "Usually the calibration is unnecessary. When you start a single color/"
#~ "material print, with the \"flow dynamics calibration\" option checked in "
#~ "the print start menu, the printer will follow the old way, calibrate the "
#~ "filament before the print; When you start a multi color/material print, "
#~ "the printer will use the default compensation parameter for the filament "
#~ "during every filament switch which will have a good result in most "
#~ "cases.\n"
#~ "\n"
#~ "Please note there are a few cases that will make the calibration result "
#~ "not reliable: using a texture plate to do the calibration; the build "
#~ "plate does not have good adhesion (please wash the build plate or apply "
#~ "gluestick!) ...You can find more from our wiki.\n"
#~ "\n"
#~ "The calibration results have about 10 percent jitter in our test, which "
#~ "may cause the result not exactly the same in each calibration. We are "
#~ "still investigating the root cause to do improvements with new updates."
#~ msgstr ""
#~ "Please find the details of Flow Dynamics Calibration from our wiki.\n"
#~ "\n"
#~ "Usually the calibration is unnecessary. When you start a single color/"
#~ "material print, with the \"flow dynamics calibration\" option checked in "
#~ "the print start menu, the printer will follow the old way, calibrate the "
#~ "filament before the print; When you start a multi color/material print, "
#~ "the printer will use the default compensation parameter for the filament "
#~ "during every filament switch which will have a good result in most "
#~ "cases.\n"
#~ "\n"
#~ "Please note there are a few cases that will make the calibration result "
#~ "not reliable: using a texture plate to do the calibration; the build "
#~ "plate does not have good adhesion (please wash the build plate or apply "
#~ "gluestick!) ...You can find more from our wiki.\n"
#~ "\n"
#~ "The calibration results have about 10 percent jitter in our test, which "
#~ "may cause the result not exactly the same in each calibration. We are "
#~ "still investigating the root cause to do improvements with new updates."

#~ msgid "Please find the cornor with perfect degree of extrusion"
#~ msgstr "Please find the corner with the perfect degree of extrusion"

#~ msgid ""
#~ "Enable this to get a G-code file which has G2 and G3 moves. And the "
#~ "fitting tolerance is same with resolution"
#~ msgstr ""
#~ "Enable this to get a G-code file with G2 and G3 moves. The fitting "
#~ "tolerance is the same as the resolution."

#~ msgid "Unload Filament"
#~ msgstr "Unload"

#~ msgid ""
#~ "Green means that AMS humidity is normal, orange represent humidity is "
#~ "high, red represent humidity is too high.(Hygrometer: lower the better.)"
#~ msgstr ""
#~ "Green means that AMS humidity is normal, orange means that humidity is "
#~ "high, and red means that humidity is too high. (Hygrometer: the lower, "
#~ "the better.)"

#~ msgid ""
#~ "A desiccant status lower than two bars indicates that desiccant may be "
#~ "inactive. Please change the desiccant.(The bars: higher the better.)"
#~ msgstr ""
#~ "A desiccant status lower than two bars indicates that desiccant may be "
#~ "inactive. Please change the desiccant. (The higher, the better.)"

#, boost-format
#~ msgid "Succeed to export G-code to %1%"
#~ msgstr "Success! G-code exported to %1%"

#~ msgid "Initialize failed (No Device)!"
#~ msgstr "Initialization failed (No Device)!"

#~ msgid "Initialize failed (No Camera Device)!"
#~ msgstr "Initialization failed (No Camera Device)!"

#~ msgid ""
#~ "Printer is busy downloading, please wait for the download to finish."
#~ msgstr ""
#~ "Printer is busy downloading; please wait for the download to finish."

#~ msgid "Initialize failed (Not accessible in LAN-only mode)!"
#~ msgstr "Initialization failed (Not accessible in LAN-only mode)!"

#~ msgid "Initialize failed (Missing LAN ip of printer)!"
#~ msgstr "Initialization failed (Missing LAN IP of printer)!"

#, c-format, boost-format
#~ msgid "Load failed [%d]!"
#~ msgstr "Loading failed [%d]!"

#~ msgid "Failed to fetching model informations from printer."
#~ msgstr "Failed to fetch model information from printer."

#~ msgid "Failed to parse model informations."
#~ msgstr "Failed to parse model information"

#, boost-format
#~ msgid ""
#~ "You have changed some settings of preset \"%1%\".\n"
#~ "Would you like to keep these changed settings (new value) after switching "
#~ "preset?"
#~ msgstr ""
#~ "You have changed some settings of preset \"%1%\".\n"
#~ "Would you like to keep these changed settings (new value) after switching "
#~ "presets?"

#~ msgid ""
#~ "You have changed some preset settings.\n"
#~ "Would you like to keep these changed settings (new value) after switching "
#~ "preset?"
#~ msgstr ""
#~ "You have changed some preset settings.\n"
#~ "Would you like to keep these changed settings (new value) after switching "
#~ "presets?"

#~ msgid "connectors is out of object"
#~ msgstr "Connectors must be on object surface."

#~ msgid ""
#~ "Invalid state.\n"
#~ "No one part is selected for keep after cut"
#~ msgstr ""
#~ "Invalid state.\n"
#~ "No one part is selected to keep after cut"

#~ msgid "Error! Unable to create thread!"
#~ msgstr "Error. Unable to create thread."

#~ msgid ""
#~ "Discribe how long the nozzle will move along the last path when retracting"
#~ msgstr ""
#~ "This describes how long the nozzle will move along the last path while "
#~ "retracting."

#~ msgid ""
#~ "Switch to rectilinear pattern?\n"
#~ "Yes - switch to rectilinear pattern automaticlly\n"
#~ "No  - reset density to default non 100% value automaticlly"
#~ msgstr ""
#~ "Switch to rectilinear pattern?\n"
#~ "Yes - Switch to rectilinear pattern automatically\n"
#~ "No  - Reset density to default non 100% value automatically"

#, c-format
#~ msgid "Density of internal sparse infill, 100% means solid throughout"
#~ msgstr ""
#~ "This is the density of internal sparse infill. 100% means that the object "
#~ "will be solid throughout."

#~ msgid "This setting specify the count of walls around tree support"
#~ msgstr "This setting specifies the wall count around tree support."

#~ msgid "Export all objects as STL"
#~ msgstr "Export All Objects as STL"

#~ msgid "The 3mf is not compatible, load geometry data only!"
#~ msgstr "The 3mf is not compatible, loading geometry data only!"

#, c-format, boost-format
#~ msgid "%s is not supported by AMS."
#~ msgstr "%s is not supported by the AMS."

#~ msgid "Don't remind me of this version again"
#~ msgstr "Don't remind me about this version again."

#~ msgid "Print sequence of inner wall, outer wall and infill. "
#~ msgstr "This is the print sequence of inner walls, outer walls, and infill."

#~ msgid "The minimum printing speed when slow down for cooling"
#~ msgstr "The minimum printing speed when slowing down for cooling."

#~ msgid ""
#~ "Material becomes soft at this temperature. Thus the heatbed cannot be "
#~ "hotter than this tempature"
#~ msgstr ""
#~ "Material becomes soft at this temperature. Thus, the heat bed cannot be "
#~ "hotter than this temperature."

#~ msgid ""
#~ "Speed of auxiliary part cooling fan. Auxiliary fan will run at this speed "
#~ "during printing except the first several layers which is defined by no "
#~ "cooling layers"
#~ msgstr ""
#~ "This is the speed of auxiliary part cooling fan. The auxiliary fan will "
#~ "run at this speed during printing except for during the first several "
#~ "layers which may be set to have no part cooling."

#, c-format, boost-format
#~ msgid ""
#~ "Bed temperature of other layer is lower than bed temperature of initial "
#~ "layer for more than %d degrees Celsius.\n"
#~ "This may cause model broken free from build plate during printing"
#~ msgstr ""
#~ "The bed temperature of other layers is lower than the bed temperature of "
#~ "the first layer by more than %d degrees Celsius.\n"
#~ "This may cause models to break free from the build plate during printing."

#~ msgid ""
#~ "Bed temperature is higher than vitrification temperature of this "
#~ "filament.\n"
#~ "This may cause nozzle blocked and printing failure\n"
#~ "Please keep the printer open during the printing process to ensure air "
#~ "circulation or reduce the temperature of the hot bed"
#~ msgstr ""
#~ "Bed temperature is higher than vitrification temperature of this "
#~ "filament.\n"
#~ "This may cause nozzle blockage and print failure.\n"
#~ "Please keep the printer open during the printing process to ensure air "
#~ "circulation or reduce the temperature of the hot bed."

#~ msgid ""
#~ "Bed temperature when high temperature plate is installed. A value of 0 "
#~ "means the filament does not support printing on the High Temp Plate"
#~ msgstr ""
#~ "This is the bed temperature when the high temperature plate is installed. "
#~ "A value of 0 means the filament does not support printing on the High "
#~ "Temp Plate."

#~ msgid ""
#~ "Style and shape of the support. For normal support, projecting the "
#~ "supports into a regular grid will create more stable supports (default), "
#~ "while snug support towers will save material and reduce object scarring.\n"
#~ "For tree support, slim style will merge branches more aggressively and "
#~ "save a lot of material (default), while hybrid style will create similar "
#~ "structure to normal support under large flat overhangs."
#~ msgstr ""
#~ "Style and shape of the support. For normal support, projecting the "
#~ "supports into a regular grid will create more stable supports (default), "
#~ "while snug support towers will save material and reduce object scarring.\n"
#~ "For tree support, slim style will merge branches more aggressively and "
#~ "save a lot of material (default), while hybrid style will create similar "
#~ "structure to normal support under large flat overhangs."

#~ msgid ""
#~ "Do not recommend bed temperature of other layer to be lower than initial "
#~ "layer for more than this threshold. Too low bed temperature of other "
#~ "layer may cause the model broken free from build plate"
#~ msgstr ""
#~ "It is not recommend for bed temperature of other layers to be lower than "
#~ "the first layer by more than this threshold. Too low bed temperature of "
#~ "other layer may cause the model to break free from the build plate."