Remove extraneous options in 20mm box config.

src/test/inputs/test_cli/20mmbox_config.ini

@@ -1,172 +1,38 @@
 # generated by Slic3r 1.3.1-dev on 2018-11-24 17:57:55
-adaptive_slicing = 0
-adaptive_slicing_quality = 75%
-avoid_crossing_perimeters = 0
-bed_shape = 0x0,270x0,270x264,0x264
-bed_temperature = 62
-before_layer_gcode = 
-between_objects_gcode = 
-bottom_infill_pattern = rectilinear
 bottom_solid_layers = 0
-bridge_acceleration = 5000
-bridge_fan_speed = 100
-bridge_flow_ratio = 1
-bridge_speed = 60
-brim_connections_width = 0
 brim_width = 0
-compatible_printers = "Fletcher 0.35";"Fletcher 0.4";Hexydelta;"Printrcore 0.4"
 complete_objects = 0
-cooling = 1
-default_acceleration = 5000
-disable_fan_first_layers = 10
-dont_support_bridges = 1
-duplicate_distance = 6
-end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
-end_gcode = M104 S0 ; turn off temperature\nG0 X-79  ; home X axis\nG28 Y0; ;home Y axis\nM84     ; disable motors\nM140 S0;
 external_perimeter_extrusion_width = 0.2
-external_perimeter_speed = 50%
 external_perimeters_first = 0
 extra_perimeters = 1
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
 extruder_offset = 0x0
 extrusion_axis = E
-extrusion_multiplier = 0.97
 extrusion_width = 0
-fan_always_on = 1
-fan_below_layer_time = 30
-filament_colour = #8200FF
-filament_cost = 17
-filament_density = 1.25
-filament_diameter = 1.75
-filament_max_volumetric_speed = 0
-filament_notes = ""
-filament_settings_id = 
-fill_angle = 45
 fill_density = 0%
 fill_gaps = 1
-fill_pattern = 3dhoneycomb
-first_layer_acceleration = 5000
-first_layer_bed_temperature = 70
 first_layer_extrusion_width = 0.2
 first_layer_height = 0.3
-first_layer_speed = 30
-first_layer_temperature = 230
-gap_fill_speed = 20
-gcode_arcs = 0
-gcode_comments = 0
-gcode_flavor = smoothie
-has_heatbed = 1
-host_type = octoprint
-infill_acceleration = 5000
-infill_every_layers = 1
-infill_extruder = 1
 infill_extrusion_width = 0
-infill_first = 0
-infill_only_where_needed = 0
-infill_overlap = 60%
-infill_speed = 80
 interface_shells = 0
 interior_brim_width = 0
-label_printed_objects = 0
-layer_gcode = 
 layer_height = 0.3
-match_horizontal_surfaces = 0
-max_fan_speed = 100
-max_layer_height = 0.3
-max_print_speed = 80
-max_volumetric_speed = 0
-min_fan_speed = 50
-min_layer_height = 0.05
-min_print_speed = 20
 min_shell_thickness = 0
-min_skirt_length = 0
-min_top_bottom_shell_thickness = 0
-notes = 
-nozzle_diameter = 0.35
-octoprint_apikey = 
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
-output_filename_format = [input_filename_base].gcode
-overhangs = 1
-perimeter_acceleration = 450
-perimeter_extruder = 1
 perimeter_extrusion_width = 0.2
-perimeter_speed = 60
 perimeters = 1
-post_process = 
-pressure_advance = 0
-print_host = 
-print_settings_id = 
-printer_notes = 
-printer_settings_id = 
-raft_layers = 0
-regions_overlap = 0
-resolution = 0
-retract_before_travel = 2
-retract_layer_change = 0
-retract_length = 0.75
-retract_length_toolchange = 10
-retract_lift = 0
-retract_lift_above = 0
-retract_lift_below = 0
-retract_restart_extra = 0.05
-retract_restart_extra_toolchange = 0
-retract_speed = 80
-seam_position = aligned
-sequential_print_priority = 0
-serial_port = 
-serial_speed = 250000
-shortcuts = support_material
-skirt_distance = 2
-skirt_height = 1
 skirts = 0
-slowdown_below_layer_time = 60
-small_perimeter_speed = 15
-solid_infill_below_area = 20
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 0
-solid_infill_speed = 20
-spiral_vase = 0
-standby_temperature_delta = -5
-start_filament_gcode = "; Filament gcode\n"
-start_gcode = M106 S0\nG90; set to absolute position\nG28.3 X-79 ; -214 for 0,0 center \nG28 Y0\nG28 Z0\nG1 Z10; move the hotend up over where the bed would be.\nG1 Y0\nM190 S60; preheat bed\nM104 S100; preheat nozzle.\nM190 S[first_layer_bed_temperature]; Wait until heatbed hits [first_layer_bed_temperature] \nM109 S[first_layer_temperature]; heat nozzle to [first_layer_temperature]C;\nG4 D10; Wait 10 seconds to settle heatbed\nG1 Y0 X0 Z10; move to origin
 support_material = 0
-support_material_angle = 0
-support_material_buildplate_only = 0
-support_material_contact_distance = 0.2
-support_material_enforce_layers = 0
-support_material_extruder = 1
 support_material_extrusion_width = 0
-support_material_interface_extruder = 1
-support_material_interface_extrusion_width = 0
-support_material_interface_layers = 3
-support_material_interface_spacing = 0
-support_material_interface_speed = 100%
-support_material_max_layers = 0
-support_material_pattern = rectilinear-grid
-support_material_pillar_size = 7
-support_material_pillar_spacing = 15
-support_material_spacing = 1
-support_material_speed = 60
-support_material_threshold = 120%
 temperature = 206
 thin_walls = 1
 threads = 16
-toolchange_gcode = 
 top_infill_extrusion_width = 0
 top_infill_pattern = rectilinear
 top_solid_infill_speed = 15
 top_solid_layers = 0
-travel_speed = 130
 use_firmware_retraction = 1
-use_relative_e_distances = 0
-use_set_and_wait_bed = 0
-use_set_and_wait_extruder = 0
 use_volumetric_e = 1
-vibration_limit = 0
 wipe = 0
 xy_size_compensation = 0
 z_offset = 0
-z_steps_per_mm = 400