Add exported config for 20mm box tests.

src/test/inputs/test_cli/20mmbox_config.ini

@@ -0,0 +1,172 @@
+# generated by Slic3r 1.3.1-dev on 2018-11-24 17:57:55
+adaptive_slicing = 0
+adaptive_slicing_quality = 75%
+avoid_crossing_perimeters = 0
+bed_shape = 0x0,270x0,270x264,0x264
+bed_temperature = 62
+before_layer_gcode = 
+between_objects_gcode = 
+bottom_infill_pattern = rectilinear
+bottom_solid_layers = 0
+bridge_acceleration = 5000
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 60
+brim_connections_width = 0
+brim_width = 0
+compatible_printers = "Fletcher 0.35";"Fletcher 0.4";Hexydelta;"Printrcore 0.4"
+complete_objects = 0
+cooling = 1
+default_acceleration = 5000
+disable_fan_first_layers = 10
+dont_support_bridges = 1
+duplicate_distance = 6
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+end_gcode = M104 S0 ; turn off temperature\nG0 X-79  ; home X axis\nG28 Y0; ;home Y axis\nM84     ; disable motors\nM140 S0;
+external_perimeter_extrusion_width = 0.2
+external_perimeter_speed = 50%
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 0.97
+extrusion_width = 0
+fan_always_on = 1
+fan_below_layer_time = 30
+filament_colour = #8200FF
+filament_cost = 17
+filament_density = 1.25
+filament_diameter = 1.75
+filament_max_volumetric_speed = 0
+filament_notes = ""
+filament_settings_id = 
+fill_angle = 45
+fill_density = 0%
+fill_gaps = 1
+fill_pattern = 3dhoneycomb
+first_layer_acceleration = 5000
+first_layer_bed_temperature = 70
+first_layer_extrusion_width = 0.2
+first_layer_height = 0.3
+first_layer_speed = 30
+first_layer_temperature = 230
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = smoothie
+has_heatbed = 1
+host_type = octoprint
+infill_acceleration = 5000
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 60%
+infill_speed = 80
+interface_shells = 0
+interior_brim_width = 0
+label_printed_objects = 0
+layer_gcode = 
+layer_height = 0.3
+match_horizontal_surfaces = 0
+max_fan_speed = 100
+max_layer_height = 0.3
+max_print_speed = 80
+max_volumetric_speed = 0
+min_fan_speed = 50
+min_layer_height = 0.05
+min_print_speed = 20
+min_shell_thickness = 0
+min_skirt_length = 0
+min_top_bottom_shell_thickness = 0
+notes = 
+nozzle_diameter = 0.35
+octoprint_apikey = 
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 450
+perimeter_extruder = 1
+perimeter_extrusion_width = 0.2
+perimeter_speed = 60
+perimeters = 1
+post_process = 
+pressure_advance = 0
+print_host = 
+print_settings_id = 
+printer_notes = 
+printer_settings_id = 
+raft_layers = 0
+regions_overlap = 0
+resolution = 0
+retract_before_travel = 2
+retract_layer_change = 0
+retract_length = 0.75
+retract_length_toolchange = 10
+retract_lift = 0
+retract_lift_above = 0
+retract_lift_below = 0
+retract_restart_extra = 0.05
+retract_restart_extra_toolchange = 0
+retract_speed = 80
+seam_position = aligned
+sequential_print_priority = 0
+serial_port = 
+serial_speed = 250000
+shortcuts = support_material
+skirt_distance = 2
+skirt_height = 1
+skirts = 0
+slowdown_below_layer_time = 60
+small_perimeter_speed = 15
+solid_infill_below_area = 20
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 20
+spiral_vase = 0
+standby_temperature_delta = -5
+start_filament_gcode = "; Filament gcode\n"
+start_gcode = M106 S0\nG90; set to absolute position\nG28.3 X-79 ; -214 for 0,0 center \nG28 Y0\nG28 Z0\nG1 Z10; move the hotend up over where the bed would be.\nG1 Y0\nM190 S60; preheat bed\nM104 S100; preheat nozzle.\nM190 S[first_layer_bed_temperature]; Wait until heatbed hits [first_layer_bed_temperature] \nM109 S[first_layer_temperature]; heat nozzle to [first_layer_temperature]C;\nG4 D10; Wait 10 seconds to settle heatbed\nG1 Y0 X0 Z10; move to origin
+support_material = 0
+support_material_angle = 0
+support_material_buildplate_only = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_extrusion_width = 0
+support_material_interface_layers = 3
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_max_layers = 0
+support_material_pattern = rectilinear-grid
+support_material_pillar_size = 7
+support_material_pillar_spacing = 15
+support_material_spacing = 1
+support_material_speed = 60
+support_material_threshold = 120%
+temperature = 206
+thin_walls = 1
+threads = 16
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_infill_pattern = rectilinear
+top_solid_infill_speed = 15
+top_solid_layers = 0
+travel_speed = 130
+use_firmware_retraction = 1
+use_relative_e_distances = 0
+use_set_and_wait_bed = 0
+use_set_and_wait_extruder = 0
+use_volumetric_e = 1
+vibration_limit = 0
+wipe = 0
+xy_size_compensation = 0
+z_offset = 0
+z_steps_per_mm = 400