- abstract class WipeTower and its descendant WipeTowerPrusaMM were merged into a single (non-abstract) WipeTower class
- all uses of WipeTower::xy struct were replaced by Eigen Vec2f (it is no longer necessary to be independent on libraries that PrusaSlicer uses)
- the WipeTowerPrusaMM.hpp/.cpp will be renamed in the next commit (hopefully it will retain its git history that way)
The priming extrusions were handled separately from the rest of the wipe tower toolchanges. In order to be able to use the logic from previous commit for them (custom toolchange gcodes etc), some unpleasant code shuffling was needed
Each toolchange now emits:
- end filament custom gcode
- toolchange custom gcode; if not provided, a standard Tn command is inserted
- start filament gcode
Hopefully it is now consistent for SE/ME printers with/without the wipe tower
The priming line does not work - will be fixed in the next commit
Missed adding [total_layer_count] to layer_gcode
Revert "Add new [total_layer_count] placeholder everywhere [layer_num] is avalible."
This reverts commit e29e766224a14e1f237908c3e5507ac5586ca5b7.
Revert "Missed adding [total_layer_count] to layer_gcode"
This reverts commit f07907a8acc450e9ae1220c6a9fe4f7c7e6d896c.
Better way to add [total_layer_count]
has been rewritten to be easier to parse.
Old format
; filament used = 19248.8mm (46.3cm3)
; filament used = 57.4
; filament cost = 1.5
; filament used = 8007.6mm (19.3cm3)
; filament used = 23.9
; filament cost = 0.6
; filament used = 0.0mm (0.0cm3)
; filament used = 0.0mm (0.0cm3)
; filament used = 0.0mm (0.0cm3)
; total filament cost = 2.1
New format
; filament used [mm] = 1600.7,1600.7,1600.7,1600.7,1600.7
; filament used [cm3] = 3.9,3.9,3.9,3.9,3.9
; filament used [g] = 4.8,4.8,4.8,4.8,4.8
; filament cost = 1.5,1.5,1.5,1.5,1.5
; total filament used [g] = 24.0
; total filament cost = 7.5
Where the non-printing extruders are filled in with zeros, and
the trailing non-printing extruders are not exported.
; filament used [g]
and
; filament cost
are only printed if non zero (material density and cost are defined)
it's scaled by 10^6 (~20b), with 10^2 (~7b) under the epsilon
also, CLIPPER_OFFSET_SCALE scale the number by 2^17, and clipper disallow the use of the 2 higher bits, so it can't go higher than 45b
* if the object is hollow and has only thin walls loops, the orientation must be enforced on gcode.cpp
* add extra_perimeters as unwanted setting for spiral vase.
* add dense infill as unwanted setting for spiral vase.
from the current Model/ModelObjects.
Fixed a possible race condition in updating Print::m_placeholder_parser
with the proposed filename / filename base.
Improved documentation (source code comments).
This is a fix of a long standing bug, where an extrusion is incorrectly
drawn from the end of the last wipe move. Interestingly enough,
this bug is in Slic3r at least since 1.2.9, but lucky enough
it only occured for single perimeter, no infill prints with wipe after
retract enabled, and only if the two successive slices were discretized
exactly the same, which is quite unlikely.
- add brim_ears setting: bool: set to true to activate this new funtino
- add brim_ears_max_angle : float : max angle for a corner to be assigned a brim ear.
